1 / 10

G.8275.x telecom time profiles

Joint IEEE-SA and ITU Workshop on Ethernet. G.8275.x telecom time profiles. Sébastien Jobert R&D expert, Orange sebastien.jobert@orange.com. Why defining time profiles in ITU-T?. New mobile applications requiring very accurate phase/time sync:

ambersmiley
Télécharger la présentation

G.8275.x telecom time profiles

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Joint IEEE-SA and ITU Workshop on Ethernet G.8275.x telecom time profiles Sébastien Jobert R&D expert, Orange sebastien.jobert@orange.com

  2. Why defining time profiles in ITU-T? • New mobile applications requiring very accurate phase/time sync: • TDD, LTE-A CoMP, MBSFN, location-based services, … • Cost/vulnerabilities of GNSS systems • Distribution of time sync by the network requested by the operators • Specific telecom requirements led to define PTP telecom profiles in ITU-T

  3. Time sync is critical for MBSFN & CoMP Phase/time reference Phase/time reference µs accuracy µs accuracy • MBSFN or LTE-A CoMP implies that the same content (or synchronized data) is delivered at the same moment by neighbor base stations (to avoid radio inteferences) • If the phase alignment is not good enough, the interferences cannot be handled by cyclic prefix

  4. Architectures & migrations

  5. PTP messages and clocks in G.8275.1 • PTP messages used in the profile: • Sync, Follow_Up, Announce, Delay_Req, and Delay_Resp; Signaling and Management messages are FFS • PTP types of clock used in the profile: • T-GM: master-only Ordinary Clock or master-only Boundary Clock • T-BC: Boundary Clock • T-TSC: slave-only Ordinary Clock • Transparent Clocks for future versions

  6. PTP modes used in G.8275.1 • Two-way mode only • One-step & two-step clocks supported • Ethernet multicast mapping (Annex F) • non-forwardable multicast address01-80-C2-00-00-0E and forwardable multicast address 01-1B-19-00-00-00 • IP mapping is under study • Message rates: 16 pps for Sync and Delay_req, 8 pps for Announce • Combination with SyncE is possible

  7. Alternate BMCA in G.8275.1 • Two modes are possible: • Fully automatic topology setup (similar to IEEE1588v1 BMCA) • Semi-automatic topology setup (in line with G.781 principles – use of Quality Levels and local priorities) • G.8275.1 allows having multiple masters active at the same time • Some PTP attributes unused (Priority1)

  8. Insights to G.8275.2 • G.8275.2 planned to cover “partial timing support” scenarios • Important use case: use of leased lines without synchronization time service Figure from G.8275

  9. PTP modes envisaged in G.8275.2 • Two-way mode • IP mapping has been agreed • Message rates: likely to be higher than in G.8275.1 • Packet selection will be performed in the T-BC and T-TSC, in order to filter traffic load-related PDV and asymmetry • BMCA topic has not yet been discussed • Transparent Clocks may be considered

  10. Conclusion • G.8275.x time PTP telecom profiles are designed to support the needs of current and future mobile technologies • G.8275.1 (full timing suport) will be finalized soon, G.8275.2 (partial timing support) is just starting

More Related