1 / 24

3.082 Final Presentation May 13, 2004 Brie Frame • Sandra Gonzalez • Angela Tong • Chenny Zhu

3.082 Final Presentation May 13, 2004 Brie Frame • Sandra Gonzalez • Angela Tong • Chenny Zhu. Objective. Design and fabricate a heat therapy device for lower back pain. Increases Circulation. Decreases pain signal transmissions. Heat Therapy.

falala
Télécharger la présentation

3.082 Final Presentation May 13, 2004 Brie Frame • Sandra Gonzalez • Angela Tong • Chenny Zhu

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. 3.082 Final Presentation May 13, 2004 Brie Frame • Sandra Gonzalez • Angela Tong • Chenny Zhu

  2. Objective • Design and fabricate a heat therapy device for lower back pain.

  3. Increases Circulation Decreases pain signal transmissions Heat Therapy Creates tension in muscles and soft tissue surrounding spine Reduces tension Strain or over-exert back Restricts proper circulation Pain signals sent to brain

  4. Design Priorities • Long-term reusability • Portability • Heat distribution • Flexibility and comfort • Long-lasting heat • Light weight

  5. Potential Portable Heat Therapy Designs • Chemical • Employ Phase Change Material (PCM) • Freezes at room temperature  releases heat • Electric • Uses battery only • Hybrid • PCM melted by battery http://www.hotsnapz.com/

  6. Energy Densities

  7. Electrical Superiority Best Worst

  8. Final Design Schematic Front View Heating Pack Circuit Insulation On/Off Switch Side View Battery Towards Body Cotton RTV Silicone Wire RTV Silicone Insulation Cotton Towards Outside

  9. Voltage Cut-off Circuit • Prevents over-discharging of battery • 7.4V > V > 6 V On • V < 6 V Off

  10. Thermostat Circuit • Switches heating pad on and off based on temperature • Hysteresis • Turns on 38°C • Turns off 42°C

  11. Constructing the Circuit • Design circuit • Assemble components on breadboard • Test circuit • Solder circuit

  12. Testing the Circuit • Voltage Cut-off Circuit • Ensure circuit is opened at < 6V • Thermostat Circuit • Fine tune Set-point temperature • Connect circuits together

  13. Battery • Design Limitations • Voltage cut-off circuit needed • 7.4V • 1300 mAh – limits heating cycle • Need special charger

  14. Battery Charger • Purpose • Prevents over-charging • Requirements • 12V DC power supply • Charge time > 1 hour • Charge Time • 12V, 800mA power supply • 1.6 hours

  15. Heat Lost to Environment Environment Insulatoin RTV Siliconccce Heating Wire Cotton

  16. Heat Flux to Body RTV RTV T = Temperature (°C) L = Length (m) k = Thermal Conductivity (W/mK) A = Surface Area Body RTV Silicone Heating Wire Cotton

  17. Heating Element • High Resistance Wire • NiCr 80/20 • 30 Gauge (0.010 in. diameter) • Resistance = 6.5 Ω/ft • Heat  Power (P = V2/R ) • Length = 26 inches • Resistance = 14 Ω • Current = 500 mA • Power = 3.5W

  18. H2O CH3OH (liquid polymer compound) (rigid, rubbery silicone) RTV Silicone • RTV = Room Temperature Vulcanization (cures in absence of heat) • Flexible, thermally conductive (0.83 W/mK), and flame retardant • Property retention at temperatures of -55°C to 200°C • Moisture from the air activates cross-linking agents • Reactions produce non-acidic byproducts

  19. Insulation and Outer Layer • Solid Silicone Rubber (Insulation) • Produced by COHRlastic • Low Thermal Conductivity 0.0037 W/mK • Flexible • Cotton (Outer Layer) • Comfort • Low cost http://www.tapecase.com/tc/rubber.asp

  20. Final Design Charge Time = 75 minutes Heat Time = 130 minutes Weight = 260g

  21. Safety Concerns • Must use in dry environment • Battery • Only use charger provided • Watch battery while charging • Charge Battery in non-flammable area • Don’t short the battery

  22. Cost Analysis

  23. Future Work • Longer lasting • Use battery with larger Ahr • Decrease size of chip • Surface mount chip • Convenient battery charger • Build simple to use charger • Attach car adapter

  24. Acknowledgements • 3.082 Teaching Staff • David Bono • Hao Wang • Yet-Ming Chiang • Course 6 lab • Course 6 friends

More Related