1 / 26

SPECIALTY POLYMER COATINGS, INC. Single Coat 100% Solids Tank Linings

SPECIALTY POLYMER COATINGS, INC. Single Coat 100% Solids Tank Linings. Tank Linings with 100% Solids. Excellent abrasion Quicker turn around (3-5 times) No VOC limitations / restrictions No solvent entrapment No inter-coat adhesion issues Higher DFT achievable.

fynn
Télécharger la présentation

SPECIALTY POLYMER COATINGS, INC. Single Coat 100% Solids Tank Linings

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. SPECIALTY POLYMER COATINGS, INC. Single Coat 100% Solids Tank Linings

  2. Tank Linings with 100% Solids • Excellent abrasion • Quicker turn around (3-5 times) • No VOC limitations / restrictions • No solvent entrapment • No inter-coat adhesion issues • Higher DFT achievable

  3. Typical uses for 100% Solids linings in storage vessels • Lining of floor and walls • Hydro Carbon tanks usually lined 1 –1.5m (3.5-5.5 feet) up wall • Chemical service tanks/vessels often entire internal surface • Secondary containment

  4. 100%Solids Linings • Petro-Chemical • Sewage / Wastewater H2S • Potable Water • Acids / Alkyds • Pulp & Paper

  5. Surface Preparation • Surface Preparation is Key!! • NACE #2 / SSPC SP10 Near White Metal – typical minimum • NACE #1 / SSPC SP5 White Metal Best (difficult on existing metal) • 2.5mil-5mil anchor profile recommend

  6. SSPC SP10 Near White Metal Grit Blast

  7. Sharp welds ground smooth prior to blasting

  8. 100% Solids Excellent at covering welds and seams jeep free

  9. Sharp angles difficult to coat / Stripe coating recommended

  10. Stripe coating of welds

  11. Advantages • Better Chemical resistance • Higher abrasion values • Higher adhesion to grit-blasted steel • Higher immersion temperatures • Less expense / single coat application • Thicker films possible (longer life) • Quick curing / faster turn-around

  12. Disadvantages • Plural Component equipment can be complicated, Experienced applicators a must! • Re-Coat times are shorter than solvinated • Off ratio application = expensive coating removal

  13. Variable ratio plural component equipment

  14. Fixed Ratio Plural Component Equipment

  15. 100% Solids linings for concrete • Again Surface Preparation is Key!!! • Grit blasting recommended to remove any loose concrete, providing a clean new substrate to increase adhesion • Bug holes need to be filled (often twice) • A moisture tolerant epoxy primer best for concrete • Green concrete needs to be cured for 26 days for best results

  16. Freshly blasted concrete

  17. Filling of bug holes

  18. Bug holes after primer • Often more bug holes are present after the primer has been applied • A second application is often required for best results

  19. Final application of 100% Solids NSF Epoxy

  20. Special Considerations • De-Humidification may be required to hold the grit blast on steel substrates • Cold climates may require insulation on the tank exterior to prevent condensation • Heating often required to cure out coatings in cold weather

  21. Ensuring Longevity / Quality • Choose and experienced qualified contractor • Research the lining/coating choice for the environment & contents • Have a NACE/SSPC qualified coating inspector present the entire job! • Ensure your contractor has experience with the lining/coating for your job • * If one bid is greatly lower than the rest there is a reason why!

  22. Jerry Holton11225 State Route 90Locke, NY 13092Office: 315-497-1528Cell: 315-283-3906 Thank you, Any Questions?

More Related