1 / 7

HBD HV status and plans

HBD HV status and plans. Itzhak Tserruya Special meeting, BNL January 29, 2007. Resistive Chain. Outside HBD. = 2.2M . Inside HBD. 28 HV segments in each GEM. R2=20M . Top GEM. = 10M . Middle GEM. Bottom GEM. Normal operation: HV= 3720V V GEM = 500V I = 150A

greenlaw
Télécharger la présentation

HBD HV status and plans

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. HBD HV status and plans Itzhak Tserruya Special meeting, BNL January 29, 2007

  2. Resistive Chain Outside HBD =2.2M Inside HBD 28 HV segments in each GEM R2=20M Top GEM =10M Middle GEM Bottom GEM • Normal operation: HV= 3720V VGEM = 500V I = 150A • Dead short in one GEM: I increases by 1.56%

  3. Status as of Jan. 26, 2007

  4. Status as of Jan. 26, 2007 • There are problems in 24 GEMs (out of 72): • 15 top • 5 middle • 4 bottom • Out of them: • 9 have a dead (or almost dead) short and the 10M has been replaced by a 20. • 9 draw high current with an almost ohmic behavior. The current ranges from 3 – 15A at about ~500V reflecting a GEM impedance of 16 – 140M. • 2 draw low current (410 and 777nA) at ~500V reflecting a very high GEM impedance (0.6 and 1.3 G). • 4 seem to have multi-strip problems and the 10M has been removed.

  5. GEM test history • All GEMs were subject to the following tests: a) in open air & clean room (WI): • ohmic test before and after framing • 100 V test after soldering the 20M resistors b) Inside test box (WI): • 520 V in CF4 • 480-500V in Ar/CO2 during the single GEM gain mapping. c) Inside glove box (SUNY): • 550 V in pure N2 • ~350 V in Ar/CO2 during the final triple GEM gain mapping. c) After installation and prior of closing the HBD (SUNY): • 100V test and capacitance test

  6. Diagnostics • There is no reason to believe that there was something wrong on the GEMs up to installation inside the HBD. • There is no reason to believe in some damaging chemistry between the CF4 and the CsI. We have accumulated experience (integral of several months of operation CF4 & CsI) and we never observed a problem. • The observations are consistent with dust inside the detector and/or some physical damage of the GEMs most likely during the transportation from SUNY to BNL. • Time may help sharpening this diagnostic or we may need to open the detector.

  7. How to proceed The big question is: • Can we operate the HBD in the present conditions? To answer this question we should first answer the two following questions: - Is the status in CF4 the same as in N2? - Is the status stable with time? Proposal: • Change to CF4 • Raise the global voltage on all modules to app. 3500 V where we should see cosmic rays. If the detectors are stable over a few days: a) replace the 10M resistor in the 9 GEMs that draw current to restore the 500V across the GEM b) leave the 2 GEMs with very high impedance w/o change. The gain in these modules can be restored by slightly raising the global HV. c) leave the GEMs with multi-strip problems w/o resistor.

More Related