Download
1 / 65
660 likes | 801 Vues
Solar Model Cars. By Bill Kuhl http://www.scienceguy.org. Background.
E N D
Solar Model Cars By Bill Kuhl http://www.scienceguy.org
Background Looking for more science projects on the Internet, I ran across ran across the Junior Solar Sprint Competition. I have been interested in alternative energy for a long time, so I decided I would build a solar powered model car. EverythingHobby had two Tamiya solar panels and one motor. I purchased the motor and the ½ volt 1200 mah panel to start with thinking both panels were the same. I later purchased the other panel which was 1.5 volts 400 mah, this would be good for experimenting with trade-offs between voltage and amperage.
For my next car I purchased the panel and motor specified for the Junior Solar Sprint Competition, in my first tests of running this car pictured above, the speed is at a jogging speed. This car was also an experiment in using bamboo to stiffen the thin plywood chassis. I also purchased a 10-pack of kit cars from Pitsco because the price is below $10 a car and I thought this would be good for a class this summer. The solar cell is rather tiny so I used lower gearing to get the car to move, but it will work fine in bright sun. The model solar cars appear to be a good activity to learn about harnessing sunlight, electricity, electric motors, gearing, and construction ideas.
The first car I built from Tamiya components I found in local hobby shop.
The second car built using solar panel and motor specified in Junior Solar Sprint rules.
Sun Zoon Lite car kit was the third car I built which is an inexpensive kit.
Applications for Photovoltaic Solar Power This large solar panel seen at the Minnesota State Fair was available for rent.
Traffic signals sometimes use solar panel to charge battery power.
Demonstrating Small Electric Motors This demonstration electric motor leaves everything exposed to show how motor operates.
Commutator and windings seen in Speed 400, a typical brushed electric motor. Note: When looking for a motor for solar power, it helps to look at the start-up current requirements as some motors require more electricity to start than others.
This Tamiya panel of the same physical size but is 1 ½ volts and 400 mah.
No load voltage of 1 ½ volt panels reads 1.71 volts in bright sun.
Lightweight wheels used for indoor radio control model airplanes, I selected the wheels on the left for my car.
At this point motor was only sitting on top of the chassis, I will shim the motor to get good mesh between gears.
View of chassis with car turned upside down, Popsicle sticks were used to stiffen rear of car where motor is mounted.
I used a spur gear from a RC car. The gear is glued to the side of the wheel.
Tamiya panel came with a swivel mount that gave me ideato replicate this for larger panel on second solar car.
Shimming the motor gave space between gears and it ran smoother.
Building Second Solar Model Car Junior Solar Sprint - specifies a certain solar panel and motor which I purchased from Solar World.
Specified solar panel produces 3 volts @ 3 watts, dimensions are 4 ½” x 13”
Motor comes with solar panel and it is the only motor allowed. The motor can not be modified in anyway either.
The Accessory bag from Solar World includes 2 shafts, 4 wheels/tires, and 3 spur gear sizes.
Bamboo skewers were used to strengthen the chassis of the car.
As with my first solar car, I used brass eyelets sandwiched between balsa. These eyelets were the kind used with medium size radio control servos.
Chassis turned upside down before I put layer of balsa on top of eyelets which completes the balsa sandwich.
Motor running, gears must mesh easily for good performance. The correct gearing is a trade off between quick enough acceleration and top speed. Small gear on motor shaft is the “pinion” and large gear is the “spur” gear.
Solar panel in the horizontal position, adjusting the panel to match the angle of the sun will make a big difference in performance.
Ping pong ball used for swivel. Straps were made plastic in a cottage cheese container.
The underside of rear half of car shows reinforcement done with plywood and bamboo.
After seeing the pivot on the Tamiya panel, I built my own swivel joint using a ping pong ball.
Platform for panel made from Popsicle sticks and thin plywood. Velcro fastens the panel to the platform, the panel could easily be switched to another car. I like to design everything to be flexible if possible.
Pitsco SunZoon Lite I ordered the 10 pack of solar cars from Pitsco which are very reasonably priced. The car goes together easily but needs very bright sun to move the car.
