1 / 47

Basic Cooling Water Treatment principles

Basic Cooling Water Treatment principles. John Cowpar Area Manager GE Water and Process Technologies. USING WATER. POTENTIAL PROBLEMS. CORROSION DEPOSITION - Fouling Biofouling Scaling . Scale Formation .

irish
Télécharger la présentation

Basic Cooling Water Treatment principles

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Basic Cooling Water Treatment principles John Cowpar Area Manager GE Water and Process Technologies

  2. USING WATER

  3. POTENTIAL PROBLEMS • CORROSION • DEPOSITION - Fouling Biofouling Scaling

  4. Scale Formation • Results in loss of heat transfer efficiency • Increased running costs • Danger of under deposit corrosion • Increased maintenance costs • Danger of bacteria • Health implications

  5. Corrosion • Destruction of plant • increased maintenance costs • Fouling • loss of efficiency due to increased pumping costs • loss of heat transfer efficiency • Increased Biological Nutrients • fouling and health implications

  6. Fouling • Loss of heat transfer efficiency • increase in running costs • Under deposit corrosion • increase in maintenance requirements • Increased biological nutrients • health implications • Blockages in system • increased operating costs and downtime

  7. Objectives of Water Treatment • MINIMISE SCALE • MINIMISE CORROSION • MINIMISE FOULING • MINIMISE BIOFOULING • MAXIMUM SAFETY • MAXIMUM EFFICIENCY • NON-POLLUTING

  8. WHAT CAUSES OUR PROBLEMS?

  9. DISSOLVED SOLIDS • e.g. CALCIUM • MAGNESIUM • SODIUM • CHLORIDE • BICARBONATE • SULPHATE • SILICA • IRON

  10. DISSOLVED GASES • e.g. OXYGEN • CARBON DIOXIDE • NITROGEN • SULPHUR DIOXIDE

  11. SUSPENDED MATTER • DUST/DIRT • CONTAMINANTS e.g. OIL • BIOLOGICAL e.g. ALGAE, FUNGI, BACTERIA

  12. TYPICAL WATER ANALYSIS CHART

  13. Water Analysis Result • pH 7.7 • Colour 3.00 HAZEN • Turbidity 9.00 F.T.U. • Solids - Suspended 5 mg/l • Chloride as Cl 44 mg/l • Alkalinity as CaC03 144 mg/l • Ammoniacal Nitrogen as N 0.140 ug/l • Iron (Total) as Fe 311 ug/l • Manganese (Total) as Mn 65 ug/l • Nitrate as N 4.0 mg/l • Total Hardness as CaC03 207 mg/l • Sulphate as S04 62.3 mg/l • Silica - Reactive as Si02 6.9 mg/l • Sulphide as S 0.015 mg.l • Carbon Dioxide - Free 2.50 mg.l • Solids - Total Diss. at 180C 347 mg/l • D.O. Concentration (Field Det.) 10.7 mg/l • Coliforms <10 /100ml • E. Coli <10 /100ml • Faecal Streptococci <1 /100ml • Sulphite Red. Clostridia 300 /20ml

  14. Hardness • Hardness is due to calcium and magnesium salts dissolved in water • All hardness salts are less soluble in hot water than in cold water (they show inverse solubility) • Different hardness salts have different levels of solubility • Hardness is normally reported as calcium carbonate

  15. EVAPORATION WINDAGE MAKE UP M = E + W + B BLEED

  16. Useful Equations E=R/100 x Temp Drop(degF)/10 W=R x 0.2/100 ( Forced Draught) W=R x 0.6/100 (Natural Draught) B=E/(C-1) -W M=E + B + W

  17. SCALE FORMATION SCALE CAN BE CONTROLLED BY: • PRE-TREATMENT • CHEMICALS • CONCENTRATION FACTOR

  18. CORROSION • Iron ore is found in nature and requires a large input of energy to convert it into steel. • Steel corrodes in order to get back to its natural (lower energy) state • Corrosion is an electrochemical process

  19. CORROSION CAN BE CONTROLLED BY: • REMOVAL OF OXYGEN ? • ADDITION OF CHEMICALS • CONTROL OF pH

  20. Biofouling

  21. What is Biofouling caused by? • FUNGI • ALGAE • BACTERIA

  22. FOULING/BIOFOULING • Can be controlled by • Filtration • Control of Concentration Factor (bleed) • Dispersants • Biocides

  23. Open Cooling • When evaporation occurs, the heat of evaporation is used to drive off the vapour • The loss of this energy results in a cooling effect in the water • Pure water is evaporated (gases may also be lost) • Dissolved solids remain in the water

  24. Cooling Water WATER DROPLET COOLS BY: EVAPORATION RADIATION CONVECTION

  25. Control of Concentration • The number of times the solids build in the system water is termed the concentration factor (CF). • CF is controlled by bleed • to increase CF - decrease bleed • to decrease CF - increase bleed

  26. Bleed Control • Effect of too much or too little bleed: • Too much bleed :- • low concentration factor • waste of water • waste of treatment • Too little bleed:- • high concentration factor • danger of scale and fouling • increased nutrient in system • danger of biofouling

  27. x While increasing concentration factor reduces water use, it also increases nutrients in the system water, encouraging growth of bacteria and slimes. Therefore, we normally run most cooling systems between 2 and 5 Water Use x x x x x 1 2 3 4 5 6 Concentration Factor

  28. Non-biological Fouling • Treated by addition of dispersants • dispersants (antifoulants) coat the particles and so keep them apart • The dispersed particles are then removed from the system water • either with the bleed or via a side stream filter

  29. Non-biological Foulants • Silt • Rust • Process contamination • all removed by dispersant/bleed • Oil • Grease • a different chemical is required but the principle is the same

  30. MICROBIOLOGY

  31. Microbiology in Industrial Cooling Systems • Problematic Microorganisms • The Biofouling Process • Water Treatment Biocides • Biocide Programming • Monitoring and Control

  32. FUNGI • Although yeast and some aquatic fungi are normally unicellular, most fungi are filamentous organisms • Fungi form solid structures which can reach a considerable size • Some wood destroying fungi exist, associated with deterioration of tower timber • Fungi require presence of organic energy source • Exist at between 5 to 38 C and pH 2 to 9 with an optimum of 5 to 6

  33. ALGAE • Classified as plants as they grow by photosynthesis • Range in size from unicellular microscopic organisms to plants that can be up tp 50m in length Single cells Multi cellular

  34. ALGAE • Algae cannot survive in the absence of air, water or sunlight • Basic difference is that algae utilise CO2 and water using sunlight as the energy source to assimilate food • Large quantities of polysaccharides (slime) can be produced during algal metabolism • Plug screens, restrict flow and accelerate corrosion • Provide excellent food source • Exist between 5 to 65 C and pH 4 to 9

  35. BACTERIA • Universally distributed in nature • Great variety of micro organisms • Multiply by cell division • Slime formation • Pseudomonas (utilise hydrocarbon contaminants) • Sulphur bacteria - anaerobic sulphate reducing bacteria • Nitrogen cycle bacteria

  36. FACTORS CONTRIBUTING TOMICROBIAL GROWTH • Rate of incoming contamination • Amount of nutrient present • pH • Temperature • Sunlight • Availability of oxygen/carbon dioxide • Water velocities

  37. THE BIOFOULING PROCESS • Bacteria prefer to colonise surfaces • enables production of biofilm which acts to protect and entrap food sources • Planktonic bacteria • free swimming in bulk water • Sessile bacteria • attached to surfaces

  38. EFFECTS OF BIOFOULING • Fouling of: tower, distribution pipework, heat exchangers • Reduction in heat transfer efficiency • Lost production • Under deposit corrosion • Inactivation/interference with inhibitors

  39. WATER TREATMENT BIOCIDES • Oxidising Biocides • Have the ability to oxidise organic matter eg. protein groups • Non-Oxidising Biocides • Prevent normal cell metabolism in any of the following ways : • Alter permeability of cell wall • Destroy protein groups • Precipitate protein • Block metabolic enzyme reactions

  40. OXIDISING BIOCIDES • Sodium Hypochlorite • Hypobromous Acid • Chlorine dioxide • Ozone • Hydrogen Peroxide

  41. Oxidising Biocides • Rapid kill • Cost effective • Tolerant of contamination • e.g. Bromine, Chlorine Dioxide • Minimal environmental impact • e.g. Bromine, Ozone, Peroxide, Chlorine Dioxide • Ineffective against SRB’s • Low residual toxicity • Counts approaching potable water standards possible

  42. Non Oxidising Biocides • Screen water • Select alternating biocide to prevent resistant strains from developing • Effective against SRB’s • Can protect system long after dosing. • Contain biodispersant • Higher dosage for kill possible • Environmentally some have rapid breakdown e.g. DBNPA

  43. BIODISPERSANTS • Improves penetration of biocide within bacterial slime • Disperse released bacteria and biofilm into bulk water for removal by blowdown • Reduces ability for bacteria to attach to system surface • Improves performance of both non oxidising and particularly oxidising biocides

  44. Physical Methods • Ultra Violet and Ultra Filtration • Only Effective At Point Of Use • Cannot Kill Sessile Organisms • Offer No Protection To Isolated Parts Of System (Static Areas) • Environmentally Acceptable.

  45. Control of Concentration • The number of times the solids build in the system water is termed the concentration factor (CF). • CF is controlled by bleed • to increase CF - decrease bleed • to decrease CF - increase bleed

More Related