1 / 27

Reducing the Time to Market for New BMC Applications

Part Design and Rapid Prototyping for BMC. Reducing the Time to Market for New BMC Applications. Part Design Guidelines for BMCs. Design Considerations for BMCs. Design to optimize inherent properties of material Use structure as-opposed to mass wherever possible

jafari
Télécharger la présentation

Reducing the Time to Market for New BMC Applications

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Part Design and Rapid Prototyping for BMC Reducing the Time to Market for New BMC Applications

  2. Part Design Guidelines for BMCs

  3. Design Considerations for BMCs • Design to optimize inherent properties of material • Use structure as-opposed to mass wherever possible • Keep “Line-of-draw” in mind to minimize reduce or eliminate undercuts and/or trapped steel conditions in mold • Add molding draft based on line-of draw to insure minimum wall sections are maintained

  4. Wall Stock for BMCs • Maintain nominal wall stock as consistently as possible. • Use structure wherever possible to increase directional strength and/or combine part features

  5. Wall Stock for BMCs Wall Stock Recommendations: • Minimum recommended wall stock 2mm • Thicker nominal walls required for larger parts with extended flow lengths • Wall stock for small parts can be as low as .5mm • Dependent on part configuration and material selection

  6. Wall Stock for BMCs Parts with Varying Wall Stock Parts with significant variances in wall stock can be successfully molded in BMC. • Avoid multiple thick-to-thin transitions • Avoid thin-to thick gate placement • Minimize or eliminate wall stock variations near dimensionally critical features

  7. Molding Draft Draft: Angle or taper added to vertical surfaces on a part to allow for release from mold during ejection. • Line-of-draw draft angle required on all vertical part surfaces • Minimum recommended draft 1-degree P/S • The more draft the better! • Add draft where possible to small vertical walls • Linear distance vs. angular draft • Draft vs. tolerances ( + draft / - draft)

  8. Molding Draft No-draft Requirements • Can be successfully molded on BMC • Eliminates secondary machining • Commonly used for bearing bores & brush-box applications. • Use only where necessary • Minimal length-of-draw • Ejector pins surfaces adjacent to feature

  9. Undercut Features in BMC Part Designs • Common in today’s BMC part designs • Complex shapes not a problem • Multiple undercuts common • Tooling technology capable • Linear or rotary (unscrewing) • Avoid “trapped steel” conditions • Consolidate multiple undercuts where possible into same line-of-draw

  10. Fillet Radii Blend intersections with fillet radii wherever possible. • Increases part strength • Improves material flow • Mold construction benefits • Mold integrity / maintenance benefits

  11. Molded In Inserts • Injection, transfer or compression process capable • Configuration dependent • Large inserts my require pre-heating Commonly utilized in automotive and electrical switch-gear applications

  12. Mounting Hardware for BMCs BMCs are hardware-friendly materials that are capable of accepting a number of common types of mounting hardware

  13. Mounting Hardware for BMCs Self-Tapping Screws • Widely used method of mounting to BMC • BT-style thread cutting screws recommended • Thread-forming screws not recommended • High torque values • Excellent torque retention

  14. Mounting Hardware for BMCs Mounting Boss Sizing for Self-Tapping Screws • Wall stock (not boss diameter) to be a minimum of 1 1/2-times the screw diameter • Thread engagement to be a minimum of 2 1/2-times the screw diameter • Pilot hole to be .002” P/S larger than root-diameter of screw • Minimal draft in mounting holes • Blind holes to be 25% deeper than installed screw engagement

  15. Mounting Hardware for BMCs Rivets • Commonly used to attach non-stressed components onto BMC parts • Used in assembly of household circuit breaker housings • Refer to hardware manufacturers recommendations for mounting geometry

  16. Mounting Hardware for BMCs Insert-Molded & Secondary-Installed Threaded Inserts Commonly used in BMC applications where service or installation requires multiple assembly / disassembly • Insert-molded • Secondary installation • Excellent retention in BMCs Refer to hardware manufacturers specifications for hole sizing & application-specific information

  17. Snap Features in BMC Part Designs Given the range of flex modulus achievable in BMCs, snap details are possible provided that they can be designed with an interference that can operate within the flex-range of the material grade selected. Feel free to contact BMCI’s Technical Group if you have a proposed snap design and would like to review it for feasibility in BMC.

  18. Direct Conversion from Metal Design • Common in BMC • Configuration dependent • May require design modifications to accommodate molding of features previously formed by secondary machining operations • Significant savings potential associated with elimination of costly secondary machining operations

  19. Direct Conversion from Metal Design Vacuum Gearbox Housing • Direct conversion from metal • Eliminated nine-(9) secondary machining operations • Implementing as running change • Minimal design changes • Annual volume 600K • Annual savings : $690K

  20. Part Consolidation Through Conversion

  21. Part Consolidation Through Conversion • Incorporation of multiple part features into one design • Part count reduction • Lower assembly tooling costs • Reduced assembly labor • Elimination of secondary machining operations • Overall lower assembly cost

  22. Surface Finishes & Appearance Treatments As Molded Finishes • High gloss • Satin • Textured • Colors • Faux finishes (as molded) • Paintable • Platable

  23. Rapid Prototyping for BMC Materials From Art to Part

  24. Rapid Prototyping for BMC Materials Overview: The ability to quickly provide customers with prototype parts in our materials has proven to be both a valuable sales tool, and an effective method of shrinking product development lead times. Since BMC thermosets do not lend themselves to traditional “Rapid Prototyping” processes such as SLA (Stereo Lithography) of SLS (Selective Laser Sintering), we have developed our own prototyping process for providing net-shapes to our customers for evaluation.

  25. Rapid Prototyping for BMC Materials Process: Our process first involves the pre-molding of plaques, or blocks of the BMC formulation selected for the application. These “Billets” of material are then laminated together using epoxy adhesives, or parent resin to form a “Blank” that is roughly the size and shape of the part. Lastly, the blank is 3D machined in our mold shop from the customer part file to produce a net-shape prototype part. We have used this process to produce parts as small as a plumbing fitting, and as large as a stove top frame.

  26. Rapid Prototyping for BMC Materials BMCI In-House Tooling / Prototyping • Part / product design assistance • Mold design • Prototype / production tooling • Prototype part construction • Tooling conversion for BMC materials

  27. Rapid Prototyping for BMC Materials BMCI In-House Tooling / Prototyping Contact Information: Mark Bieberstein Technical Sales Engineer (630) 377-1065 (630) 377-7395 Mark_B@Bulkmolding.com

More Related