1 / 20

Coal System

Coal System. Combustion optimization Coal G3 Online measurement of the coal mass flow between the mill and the burner Real time!. Example Pipe Arrangement. Receiver. Transmitter. A. w. o. l. f. s. s. a. m. In case of roping: cover full cross section.

jasia
Télécharger la présentation

Coal System

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Coal System Combustion optimization Coal G3 Online measurement of the coal mass flow between the mill and the burner Real time!

  2. Example Pipe Arrangement

  3. Receiver Transmitter A w o l f s s a m In case of roping: cover full cross section Easy installation: The sensors are mounted through easy drill and tap holes (14x1 mm) MECONTROLCoalMeasurement Principle „density“ Microwave measurement: 2 sensors in one pipe are used to measure the coal concentration over the FULL cross sectional area of the pipe.

  4. Signal Sensor 1 Coal Dust Pipe “Signature” Signal Sensor 2 Sensor 2 Sensor 1 X(t) Y(t)=X(t-T) S=const. T=-26 ms Optimum of correlation “Correlation” correlation Time T Example S=54 cm T=26 ms w=20,8 m/s (average velocity of the particles !) MECONTROL CoalMeasurement Principle „velocity“ Velocity W=S/T

  5. Measurement Cabinet Microwave Board D-HF Amplifier VCO MW-Output Time basis Processor MW-Input Data output Power input Temp.input RS 232 MECONTROL Coal Measurement Cabinet

  6. G3-Sensor Temperature measurement sensor MECONTROL Coal Sensor installation

  7. NEW MECONTROL COAL G3 System

  8. 1 h high time resulution plot of mass flow and velocity

  9. Mill shut down sequence over 4:40 h time window

  10. Derived mill parameters t1 t2 Mill response time can be derived, Impact on load changes, Indication for mill wear and coal grindability

  11. Mill Quality monitoring: Low standard deviation of concentrations and velocities Variation of velocity 1s: 0.7 m/s (2.1 ft/sec) Variation of coal loading 1s: 50 g/m

  12. MECONTROL Coal Velocity Velocity is measured using a cross correlation technique (picture: pipes 1 through 8). Measurement range: 5 m/sec to 50m/sec

  13. MECONTROL Coal Absolute mass flow Out of the independent measurement values, density and velocity, the absolute mass flow is calculated without using any feeder signal. Measurement range: 10 g/sec to 20 kg/sec

  14. MECONTROL Coal Combustion optimization by Secondary air control without control active control

  15. we focus on your process O2 NOx CO MECONTROL boiler optimization with secondary air control using MECONTROLCoal

  16. Air-to-Fuel Ratio

  17. Burner Air Register Settings Air Register Settings [%] 50-20-20-20-20-20-20-50 O2 setpoint 3.1% 50-20-20-20-20-30-50-80 O2 setpoint 3.1% 50-20-20-20-20-20-50-80 O2 setpoint 3.1% 50-20-20-20-20-20-50-80 O2 setpoint 2.5% 50-20-20-20-20-20-50-80 O2 setpoint 2.2% 50-20-20-20-20-30-50-80 O2 setpoint 2.2% Right boiler sidewall Left boiler sidewall

  18. Variable Orifices Example Pipe Arrangement

  19. Damper Location on the Top of the Classifier Damper, one sided; direction against flow rotation Damper as close as possible on the top of the classifier

  20. MECONTROL Coal References • Since 1998 in total ca. 600 Measurement Installations at 45 Plants worldwide • Countries: Germany, USA, Japan, Turkey, Denmark • Customers: E.ON, Mainova, SaarEnergie, STEAG, EnBW, J-Power, AEP, Allegheny Energy, LG&E, NSP, Mission Energy, TVA, Alliant Energy, Dynegy, Consumers Power, First Energy, Santee Cooper, SCE&G, Xcel Energy

More Related