1 / 16

Chopper for the MEBT

Chopper for the MEBT. Chopper for the MEBT. Point of the chopper: Linac Bunches are spaced by 325 MHz ( 3.1ns ) In MI, bunch spacing is ~ 53 MHz (~19ns ) Don’t want bunches in the 53 MHz seperatrix =>Chop out ~1 of every 6 bunches Additional complication: 325 ≠n∙53

jeanne
Télécharger la présentation

Chopper for the MEBT

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Chopper for the MEBT

  2. Chopper for the MEBT • Point of the chopper: • Linac Bunches are spaced by 325 MHz (3.1ns) • In MI, bunch spacing is ~53 MHz(~19ns) • Don’t want bunches in the 53 MHz seperatrix =>Chop out ~1 of every 6 bunches Additional complication: 325≠n∙53 =>Sometimes chop 1, sometimes 2

  3. Chopper for the MEBT • Only 3ns between bunches => use a travelling wave deflector which follows the beam • Since b=0.073 @2.5 MeV, need to slow down pulse => use meander wave structure: • Georgio obtained a prototype at CERN (from Fritz Caspers)

  4. Trace3d output from Gennady Chopper goes here; Allowed length TBD 28 cm long 70 cm

  5. A few numbers • Electrostatic deflection:d=(V/a)L2/2bp a=plate spacing, V=voltage, L=length • ~1kV,~2ns rise @53 MHz is very challenging • From CD0 param list: a=1.8cm, L=45cm, V=±1.8kV (assuming 3MeV beam) Chopperplates Begin solenoid

  6. A few more numbers • Allow beam to hit chopper plates • Spacing can be smaller, V requirement lower • For instance: with V=±885V, d=1.2cm, L=45cm: Chopperplates Begin solenoid

  7. CERN prototype • Ag /Moly-Mn on alumina • Layout for 3 Mev (b=0.08) • Only (10-15um of Ag (prototype) • Measured S21, consistent with CERN measurements

  8. Measurements CERN D. Wildman/R. Madrak 19 cm prototype

  9. More measurements S21 beyond 1 GHz: First resonance @1.5GHz Complex impedance: @53 MHz, 48.996Ω, 600pH

  10. Reminder: what it has to do • Bunch spacing = 3ns, bunch width=0.5ns • width <~5.5ns, including rise and fall • At full voltage for >~ 0.5 ns • 53 MHz rep rate, DF of 1ms*10Hz = 1% • Minimal(?) ringing after pulse • Measurements show the structure has no problem with this. • The most challenging part is the pulser

  11. Response to ‘the perfect’ low V pulse First try: fast scope calibration pulse, thru heliax->meander third try: fancy 2ns pulser (not available for use) Fourth try: borrowed HP8130A pulse gen 2nd try: same as above, Thru RG58

  12. Response to imperfect higher V pulse Input waveform: 100V, 400ps rise 1.3 GHz ringing After meander: 1 ns rise, 890 MHz ringing

  13. High Voltage Amplifier: what’s been done • SNS fast chopper: array of ~1ns risetime DEI FET’s to achieve ±2350V, 10ns risetime • SPL: two tubes providing high/low freq. components • Were not able to achieve 8ns (low) risetime with 45 MHz rep rate • RAL: seem to have a pulse generator (made by Kentech, U.K.), (but rep rate of only 2.4MHz):

  14. Forseeable options for pulser • FET’s (DEI/IXYS) • Risetime almost sufficient, falltime not (can solve with additional FET?) • Rep rate/duty factor worrisome for burnout • A module designed by DEI? • Kentech? • High power amplifier • E.g. IFI 1kHz-1GHz solid state and tetrode tube combo • D. Wildman got a quote of ~$60k • Probably need more than 1

  15. Measurements with DEI FET • Pulse width limited to 8ns by driver • Got up to 200k pulses @20MHz (10ms total); repeated at 3Hz • Need to heat sink next time

  16. To consider • How much space is available? • Chopped beam • Dump into chopper? • And/or target? • What about solenoids? • Tolerable residual V on meander (do not want to disturb chopped beam) • Pulser issues

More Related