1 / 33

Building a Heart

Building a Heart. In Second Life. Atrium/Ventricle. 1) In the Build menu on the top navigation bar, select Build or Ctrl + B. 2) On the pop-up window, select Create (Note: wand icon, as show in Figure 2.1). 3) Select Hemisphere. Figure 2.1. Atrium/Ventricle.

kalea
Télécharger la présentation

Building a Heart

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Building a Heart In Second Life

  2. Atrium/Ventricle 1) In the Build menu on the top navigation bar, select Build or Ctrl + B. 2) On the pop-up window, select Create (Note: wand icon, as show in Figure 2.1). 3) Select Hemisphere. Figure 2.1

  3. Atrium/Ventricle 4) Click on the ground with the Wand tool (Note: The hemisphere you selected now appears). 5) Under the General tab, change the name to Left Atrium/Ventricle. 6) Select the Object tab; change the properties according to Figure 2.2 exceptfor its position. Figure 2.2

  4. Atrium/Ventricle 7) Repeat steps 2 through 5 and change the hemisphere’s name into Right Atrium/Ventricle. Before After Figure 2.3

  5. Atrium/Ventricle 8) For the second hemisphere, select the Object tab and change its properties according to Figure 2.4 exceptfor its position. After Before Figure 2.5 Figure 2.4

  6. Atrium/Ventricle • Adjust the position of both the Left and Right Atrium/Ventricle to make a heart shape as shown in Figure 2.6. • Hold the Shift key and left click on both Left and Right Atrium/Ventricle. Press Ctrl + L to link these two parts. Figure 2.6

  7. Atrium/Ventricle 11) Create a sphere and change the properties according to Figure 2.7 except for its position. After Before Figure 2.8 Figure 2.7

  8. Atrium/Ventricle • Put this separator in the middle of the heart shape as shown in Figure 2.9. • Link the separator with the heart shape by holding Shift and clicking them and then press Ctrl + L. Figure 2.9

  9. Atrium/Ventricle 14) Create four Toruses (Note: two for Left Atrium/Ventricle, two for Right Atrium/Ventricle)

  10. Atrium/Ventricle 14-1) Left Atrium/Ventricle(Create two toruses and change its properties according to Figure 2.10 except for its position). Figure 2.10

  11. Atrium/Ventricle 14-2) Position of the two toruses as shown in Figure 2.11 and link them to the Left Atrium/Ventricle. Figure 2.11

  12. Atrium/Ventricle 14-3) Right Atrium/Ventricle(Create two toruses and change its properties according to Figure 2.12 except for its position). Figure 2.12

  13. Atrium/Ventricle 14-4) Position of the two toruses as shown in Figure 2.13 and link them to the Left Atrium/Ventricle. Figure 2.13

  14. Superior Vena Cava • Create a tube and change its Object properties according to Figure 2.14 except for its position. Figure 2.14

  15. Superior Vena Cava 2) Change the tube’s Texture properties according to Figure 2.15. After Before Figure 2.15 Figure 2.16

  16. Superior Vena Cava 3) Create a second tube and change its Object properties according to Figure 2.17 except for its position. Figure 2.17

  17. Superior Vena Cava 4) Change the second tube’s Texture properties according to Figure 2.18. Before After Figure 2.18 Figure 2.19

  18. Superior Vena Cava • Position the two tubes to the heart as show in Figure 2.20. • Link these two tubes to the heart by holding the Shift key, and left click each part and then click Ctrl + L. Figure 2.20

  19. Arch of Aorta 1) Create a torus and change its Object Properties according to Figure 2.21 except for its position. Before Figure 2.22 After Figure 2.21

  20. Arch of Aorta 2) Position the torus on the heart as shown in Figure 2.23. Figure 2.23

  21. Arch of Aorta 3) Create another torus and change its Object properties according to Figure 2.24 except for its position. Before After Figure 2.25 Figure 2.24

  22. Arch of Aorta 5) Position the torus to the heart as shown in Figure 2.26. Figure 2.26

  23. Arch of Aorta 6) Create three tubes and change its Object properties as shown in Figure 2.27. Name them as A1, A2, and A3 (Do not copy its position). Figure 2.27 A1

  24. Arch of Aorta Figure 2.27 A2 A 3

  25. Arch of Aorta A1 A2 A3

  26. Arch of Aorta • Position A1, A2, and A3 as shown in Figure 2.29. • Link all the parts created in Arch of Aorta to the heart by holding Shift and clicking each piece. Then, press Ctrl + L. A1 A2 A3

  27. Pulmonary Artery 1) Create a torus and change its Object properties shown in Figure 2.30. Do not change its position. Before Figure 2.31 After Figure 2.30

  28. Pulmonary Artery 2) Create another torus; change the Object properties shown in Figure 2.32. Ignore its position. Before After Figure 2.33 Figure 2.32

  29. Pulmonary Artery Second Torus 3) Position the two toruses to the heart shown in Figure 2.34. 4) Hold the Shift key and left click on the two toruses and the heart. Then, press Ctrl + L. First Torus Figure 2.34

  30. Pulmonary Artery 5) Change the texture of the pulmonary artery to “Blank” and change the color according to Figure 2.35. Figure 2.35

  31. Heart Texture 1) Upload the texture shown in Figure 2.36 that can be obtained from http://partnersah.vet.cornell.edu/avianatlas/sites/agilestaging.library.cornell.edu.avian-atlas/files/avian_atlas_assets/38a_kidney_texture%20x750.jpg into your inventory on Second Life. Figure 2.36

  32. Heart Texture 2) Select the heart and go to the Texture tab. Click on the box above Texture and select My Inventory> Textures and then select “heartTexture”.

  33. Heart Model

More Related