Vents 101

1. Vents 101 Ted Lee,MD

2. Objectives • Understand the basics of vent mechanics • Describe the various modes of ventilation • Learn how to initiate mech. ventilation • Learn how to troubleshoot problems • Vent demonstration workshop with Hank Lockridge, RCP, RRT

3. Basic Vent Mechanics • Ideal gas law PV=nRT • Volume is inversely related to pressure • You can’t control both vol. and pressure • Choose one as the constant and the other one varies. • Basically, modes of ventilation are broken down into pressure or volume.

4. Pressure as the Constant • Pressure Control • Constant pressure over a preset time • Tidal Volume will vary depending on compliance and resistance • Modes can be AC or SIMV • Pressure Support • Constant pressure at a preset flow rate • Support breaths end when flow rate decreases from initial rate to a preset level. • Pt controls RR, which is the most comfortable.

5. Volume as the Constant • Volume-cycled ventilation • Tidal volume is preset • The pressure then varies • Therefore we need to set pressure alarms • Basic Modes are AC or SIMV • AC – extra breaths are at full tidal volume • SIMV – set backup rate and extra breaths are at variable volumes based on pt effort and pressure support.

6. Pros and Cons of each mode Mode Pros Cons

7. Initiation of Ventilation • Choose a mode that will: • Provide adequate oxygenation • Reduce work of breathing • Provide synchrony b/w pt and vent • Avoid high peak/plateau pressures • Start Fi02 at 100%, then titrate down • Initial Tidal Volume of 10cc/kg • Keep Plateau pressure less than 30

8. Initiation of Ventilation (cont.) • Consider PEEP, start at 5 then titrate up • Provide enough PS if using SIMV • Watch out for Auto-PEEP! • Provide adequate sedation and analgesia • If you make any changes, observe closely to see how the changes affect your patient.

9. Trouble Shooting • If BP or HR suddenly drops or pt codes: • Disconnect pt from vent and start bagging • Look for mucous plug, tension ptx, etc. • Bag slowly to allow enough expiratory time • If high pressure alarm goes off: • Look for pt/vent asynchrony • Is there a better mode? • Is pt adequately sedated? • What’s the problem with the ABG? Oxygenation (PaO2) or Ventilation (PaCO2)?

10. Vent dynamics affecting PaO2 • Fi02 • Mean Airway Pressure • PEEP

11. Vent dynamics affecting PaCO2 • Respiratory Rate • Tidal Volume • Dead Space

12. Compliance vs. Resistance • Peak pressure is Dynamic Compliance which includes airway resistance • Plateau pressure is Static Compliance • Roughly speaking, resistance is the difference between Peak and Plateau pressures.

13. Peak and Plateau Pressures www.ccmtutorials.com

14. Compliance Problem • Plateau pressure is elevated > 30 • Peak pressure is only slightly higher than plateau pressure • Decrease the tidal volume as tolerated • Treat the underlying problem • Pneumonia? • Pulmonary edema? • Tension Pneumothorax?

15. Resistance Problem • Peak pressure is elevated • Plateau pressure is usually normal • Allow for enough expiratory time • Watch for Auto-PEEP • Treat the underlying problem • Bronchoconstriction? • Mucous plugging? • Kinked endotracheal tube?

16. Auto-PEEP • What is it? • Air gets in, but not all of it comes out. • “Breath Stacking” which increases intrathoracic pressure & dec. venous return • Decrease tidal volume as tolerated • Increase expiratory time by: • Decreasing respiratory rate • Increasing inspiratory flow rate

17. www.ccmtutorials.com

18. www.ccmtutorials.com

19. Example of Auto-PEEP www.ccmtutorials.com

20. References and Resources • Fundamentals of Critical Care Support, Society of Critical Care Medicine • www.ccmtutorials.com