1 / 27

Career & Technical

Career & Technical. Education. 006.00 Demonstrate basic dimensioning techniques. 1. To describe an object completely, a drafter needs to define both the shape and the size of the object. 2.

mmargery
Télécharger la présentation

Career & Technical

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Career & Technical Education 006.00 Demonstrate basic dimensioning techniques 1

  2. Todescribean object completely, a drafter needs to define both the shapeand thesizeof the object. 2

  3. After all, a machinist cannot build a part, a carpenter cannot build a house, unless all the sizes on the drawing are accurate and complete. 3

  4. Another name forsize descriptionisDimensioning. 4

  5. Standards for dimensioning technique, dimension placement, and general rules for dimensioning are published inDimensioning and Tolerancing, ASME Y14.5M-1994. 4

  6. Dimensioning Techniques 1

  7. DIMENSIONING INCLUDES MEASUREMENTS, NOTES AND SYMBOLS 6

  8. PLACEMENT OF DIMENSIONS 7

  9. ARROWHEADS SIZE AND STYLES 8

  10. DIMENSIONING DIAMETERS 9

  11. DIMENSIONING RADIIwhich do not need their centers located 10

  12. DIMENSIONING RADIIwhen locating the radius center. 11

  13. Decimal Inch • Decimals are the ANSI standard. • Decimals are easier to add, subtract, multiply and divide than fractions. • Preferably, decimals should be rounded to two decimal places (Unless more precision is required).

  14. Metric • Where linear measurement are less than 10,000 millimeters, the millimeter is the standard unit of measure. • The abbreviation for millimeters (mm) is usually omitted when all dimensions are in millimeters. • The period is used as a decimal point only in English speaking countries, others use a comma.

  15. Leading and Trailing Zeros Inches Millimeters Show trailing zerosOmit leading zeros .250.500.875 Show leading zerosOmit trailing zeros 0.250.50.875 Values less than one unit Show trailing zeros 1.0001.5001.875 Omit trailing zeros 11.515 Values greater than or equal to one unit

  16. The following are a few basic rules that summarize what might well be a list of hundreds of very specific rules that apply to dimensioning. Review the list carefully. Make each of these items a part of your dimensioning practices. 12

  17. Each dimension should be clearly shown and stated so that it can be interpreted in only one way. 13

  18. Dimensions should not be duplicated or given on a drawing in two different ways. 14

  19. Dimensions should be placed in the view where the best shape and true form are shown. 15

  20. Avoid long extension and leader lines. 16

  21. Place a dimension between views, especially if it applies to both views and will improve clarity. 17

  22. Do not assume that a part is symmetrical. Dimension both sides of a symmetrically shaped part or use the centerline symbol or note to avoid confusion. 18

  23. Spacing between dimensions should be consistent within a drawing. 19

  24. Line up dimensions horizontally and vertically where possible. 20

  25. Avoid crossing dimension lines or leaders where possible. 21

  26. Make full use of notes, abbreviations, and symbols to show how many times a dimension applies. For example, use 2X in a note to designate that a detail specified in the note exists in two places on the drawing. Dimension separately if the times (X) designation would be confusing. 22

  27. Good Luck! 23

More Related