1 / 9

ST NAND Flash DOWNLOAD

ST NAND Flash DOWNLOAD. Prepare 　ＩＴＥＭ . PC - Run Tftpd32 program. (Tftpd32-3.28-setup.exe install ) 2. Download DVR B/D 3. Download Serial B/D 4. LAN CABLE. After Download, Please update New Final Firmware. File need to download

nalani
Télécharger la présentation

ST NAND Flash DOWNLOAD

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. ST NAND Flash DOWNLOAD

  2. Prepare　ＩＴＥＭ. • PC • - Run Tftpd32 program. • (Tftpd32-3.28-setup.exe install) • 2. Download DVR B/D • 3. Download Serial B/D • 4. LAN CABLE After Download, Please update New Final Firmware.

  3. File need to download • Make a PCC:\tftpserver. Folder and copy files • No Space in Between. Any name possible • Ex) c:\tftpsever -> O • c:\tftp sever -> X • DvrStarter(VerXXX) -> Download Program • DVRFlasher(UBL128M) -> 4CH Boot Loader. • DVRFlasher(UBL256M) -> 8/16CH Boot Loader. • U-boot_st04_XX -> 4CH u-bootFile • U-boot_st16_XX -> 8/16CH u-bootFile • Kernel_st_XX -> 4/8/16 Kerrnel File • St04.X.X.XXXX.jffs2 -> 4CH RootFS image file • St16.X.X.XXXX.jffs2 -> 8/16CH RootFS image file

  4. PCIP Address 1. AssignC:\tftpserver 2. Diaable 3. 1,2Process, and OK RUN Tftpd32 Server - The program must be in running when download firmware to DVR board

  5. Ex) 8cHM/B Pin 1 Pin 1 Pin 1 4CH – J1 8/16CH – J13 DVR Main B/D& Serial Connected * WarnningCablemust be in right direction !!!

  6. RUNDvrStarter • C:\tftpserver\DvrStarter(Ver1.2.0).EXE • DVR B/D – SERIAL B/D – PCConnected. • DVR B/D – PC&LAN(RJ45)Connected. • DVR B/DPowerON • Make Sure PCTftpd32is RUNNING. • Select COM port. • ClickConnect tosee messages.

  7. U-boot • Download Step • Select U-boot File and RunU-boot. • - 70Sec. • - Dos Windows will appear, and disappear, and show BOOTME on the windows • - Press DVR B/DRESET(SW3), will use U-boot for booting.

  8. Sever IP DVR IP Board Type 2. Sever IP. - 1sec. - Sever IP is PCIP, When run Tftpd32 - Previous Message will be deleted and see new messages. 2. Input IPand ClickServeIP. - 1Sec - Change the last IP address match with SEVER IP. 3. DVR B/D Select, and Board Type (Warning!!) - 1 Sec

  9. Kernel RootFS New MAC Reset 5. SelectKernel File and run Kerrnel. - 10 sec. 6. Select Root File System , Run RootFS. - 4ch– 80sec - 8/16ch–100sec 7. Input DVR B/DMAC adress, Click New MAC - 1Sec. - After Process (7), Move to TEST Process. 8. Click Reset, Reboot DVR - After Process about 70 Sec. 9. After Booting, Update New Final Firmware

More Related