1 / 11

Using DEM models to test for 2 thermal components in 23-Jul-2002 flare

Using DEM models to test for 2 thermal components in 23-Jul-2002 flare. J. McTiernan 26-Aug-2009. A.Caspi: Fit spectra for July 23 flare, using detector 4, with improved cal. results, which he can explain in a future meeting. Fits include lines, nonthermal component, 2 thermal components.

nuwa
Télécharger la présentation

Using DEM models to test for 2 thermal components in 23-Jul-2002 flare

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Using DEM models to test for 2 thermal components in 23-Jul-2002 flare J. McTiernan 26-Aug-2009

  2. A.Caspi: Fit spectra for July 23 flare, using detector 4, with improved cal. results, which he can explain in a future meeting. Fits include lines, nonthermal component, 2 thermal components. Spectra for thermal continuum consistently fit well to two components, and those components are well-behaved in time. Low T component from 14 to 24 MK, high T component from 22 to 40 MK. The question is, can a DEM calculation resolve two components? We can test this. Motivation:

  3. Calculations all use a temperature response matrix obtained by integrating fluxes from CHIANTI_KEV over DRM’s from ospex object. Given EM(T), model counts in channel i: mi =Ri(T)#[EM(T)*dT] Gain offset, and pulse-pileup are accounted for by fixing the model count rate before comparison with obs. data. Uses Amoeba function for minimization of χ2. Fit is to expected continuum thermal component – Observed counts spectrum minus the expected counts spectra for nonthermal and lines. DEM calculation: Note that these curves are for Att_state=0, and are shown for example purposes only, and were not used for the fits.

  4. Methods for DEM calculation: 1 • NTEEMFIT: The DEM is a series of N delta-functions in T. This is similar to the single temperature or two-temperature fit from SPEX, but calculated differently, and has the option of more than two components. • First try 1 component, obtain reduced χ2, defined as: • Next try 2 components, compare new value to old one, if it’s smaller, keep it. • Keep adding components until you get a minimum value. • For this case we hope that we get two components with T and EM close to the SPEX values. (It turns out to work well.) This provides a sanity check for the T response curves.

  5. Methods for DEM calculation: 2 • NBINFIT: The DEM is a histogram with the EM defined in N temperature bins. Here’s a sample plot. • First try a small number of bins, obtain reduced χ2, defined as: • Next add a bin, compare new value to old one, if it’s smaller, keep it. • Keep adding bins until you get a minimum value. • For this case we hope that we get two bins with width of a few MK, separated by 20 MK or so with T and EM close to the SPEX values.

  6. Methods for DEM calculation: 3 • NPLFIT: The DEM is an N-component power law in T. • First try a small number of PL components (usually 1, 2 or 3), obtain reduced χ2, defined as: • Next add a PL, compare new value to old one, if it’s smaller, keep it. • Keep adding PL’s until you get a minimum value. • For this case we also hope that we get two peaks separated by 20 MK or so with T and EM close to the SPEX values. From tests for 2008 AGU poster, we expect that this should work.

  7. Nbin fit for Interval 17: Nteem fit: Black +’s from SPEX, red +’s from Nteem fit. Good agreement, ~1 MK for low T, < 1MK for high T. Also 2 T’s fit better than 1 T or 3T’s. • Nbin fit not bad, this sort of resolves into two T components. But … • Χ2 for this DEM is about twice the value for the Nteem model. • Also (next slide) final results seem to be dependent on initial model input. • This suggests that there are some systematic errors, and that the fit is finding local minimum.

  8. Another Nbin fit for Interval 17: • This also sort of resolves into two T components. But … • Here the initial condition was the Nteem fit (Actually 2 1MK bins with the EM calculated from that fit.) It *should* have stayed there.

  9. Npl fit for interval 17: • Again a hint of two components. (Error bars aren’t shown here, but tend to get very large for T<10 MK.) • Again a (smaller) dependence on the initial model. • Again a higher χ2 than the Nteem fit. • Systematically lower high T peak.

  10. Residuals: (Full Spectrum)

  11. Conclusions: • The Nteem fit procedure recovers the two T components from the SPEX fits pretty well, giving confidence in T response calculations. (Note that this is true for all time intervals) • The Nbin fit performs less well – there seem to be some systematic effects that need to be dealt with, and it looks as if fit procedure is stuck near a local minimum. • The Npl fit does show a small second component at high T, but this also looks as if there are some systematic effects. • Future work, use Monte Carlo fitting procedure (very slow in IDL).

More Related