1 / 18

General-Purpose Processors: Software

General-Purpose Processors: Software. Introduction. General-Purpose Processor Processor designed for a variety of computation tasks Low unit cost, in part because manufacturer spreads NRE over large numbers of units Motorola sold half a billion 68HC05 microcontrollers in 1996 alone

paytah
Télécharger la présentation

General-Purpose Processors: Software

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. General-Purpose Processors: Software

  2. Introduction • General-Purpose Processor • Processor designed for a variety of computation tasks • Low unit cost, in part because manufacturer spreads NRE over large numbers of units • Motorola sold half a billion 68HC05 microcontrollers in 1996 alone • Carefully designed since higher NRE is acceptable • Can yield good performance, size and power • Low NRE cost, short time-to-market/prototype, high flexibility • User just writes software; no processor design • “microprocessor” – “micro” used when they were implemented on one or a few chips rather than entire rooms

  3. Processor Control unit Datapath ALU Controller Control /Status Registers PC IR I/O Memory Basic Architecture • Control unit and datapath • Note similarity to single-purpose processor • Key differences • Datapath is general • Control unit doesn’t store the algorithm – the algorithm is “programmed” into the memory

  4. +1 Datapath Operations • Load • Read memory location into register Processor Control unit Datapath ALU • ALU operation • Input certain registers through ALU, store back in register Controller Control /Status Registers • Store • Write register to memory location 10 11 PC IR I/O ... Memory 10 11 ...

  5. Processor Control unit Datapath ALU Controller Control /Status Registers PC IR R0 R1 I/O ... Memory 100 load R0, M[500] 500 10 101 inc R1, R0 501 ... 102 store M[501], R1 Control Unit • Control unit: configures the datapath operations • Sequence of desired operations (“instructions”) stored in memory – “program” • Instruction cycle – broken into several sub-operations, each one clock cycle, e.g.: • Fetch: Get next instruction into IR • Decode: Determine what the instruction means • Fetch operands: Move data from memory to datapath register • Execute: Move data through the ALU • Store results: Write data from register to memory

  6. Control Unit Sub-Operations Processor • Fetch • Get next instruction into IR • PC: program counter, always points to next instruction • IR: holds the fetched instruction Control unit Datapath ALU Controller Control /Status Registers PC IR 100 R0 R1 load R0, M[500] I/O ... Memory 100 load R0, M[500] 500 10 101 inc R1, R0 501 ... 102 store M[501], R1

  7. Control Unit Sub-Operations • Decode • Determine what the instruction means Processor Control unit Datapath ALU Controller Control /Status Registers PC IR 100 R0 R1 load R0, M[500] I/O ... Memory 100 load R0, M[500] 500 10 101 inc R1, R0 501 ... 102 store M[501], R1

  8. Control Unit Sub-Operations Processor • Execute • Move data through the ALU • This particular instruction does nothing during this sub-operation Control unit Datapath ALU Controller Control /Status Registers 10 PC IR 100 R0 R1 load R0, M[500] I/O ... Memory 100 load R0, M[500] 500 10 101 inc R1, R0 501 ... 102 store M[501], R1

  9. Control Unit Sub-Operations Processor • Store results • Write data from register to memory • This particular instruction does nothing during this sub-operation Control unit Datapath ALU Controller Control /Status Registers 10 PC IR 100 R0 R1 load R0, M[500] I/O ... Memory 100 load R0, M[500] 500 10 101 inc R1, R0 501 ... 102 store M[501], R1

  10. Processor Control unit Datapath ALU Controller Control /Status Registers PC IR R0 R1 store M[501], R1 Fetch ops Store results Fetch Decode Exec. I/O ... Memory 100 load R0, M[500] 500 10 101 inc R1, R0 501 11 ... 102 store M[501], R1 Instruction Cycles PC=100 Fetch ops Store results Fetch Decode Exec. clk PC=101 Fetch ops Store results Fetch Decode Exec. clk 10 11 102 PC=102 clk

  11. (a) (b) Implementation Phase Implementation Phase Verification Phase Development processor Debugger/ ISS External tools Programmer Verification Phase Emulator Testing and Debugging

  12. General-purpose processors • Sometimes too general to be effective in demanding application • e.g., video processing – requires huge video buffers and operations on large arrays of data, inefficient on a GPP • But single-purpose processor has high NRE, not programmable • ASIPs – targeted to a particular domain • Contain architectural features specific to that domain • e.g., embedded control, digital signal processing, video processing, network processing, telecommunications, etc. • Still programmable Application-Specific Instruction-Set Processors (ASIPs)

  13. For embedded control applications • Reading sensors, setting actuators • Mostly dealing with events (bits): data is present, but not in huge amounts • e.g., VCR, disk drive, digital camera (assuming SPP for image compression), washing machine, microwave oven • Microcontroller features • On-chip peripherals • Timers, analog-digital converters, serial communication, etc. • Tightly integrated for programmer, typically part of register space • On-chip program and data memory • Direct programmer access to many of the chip’s pins • Specialized instructions for bit-manipulation and other low-level operations A Common ASIP: Microcontroller

  14. Another Common ASIP: Digital Signal Processors (DSP) • For signal processing applications • Large amounts of digitized data, often streaming • Data transformations must be applied fast • e.g., cell-phone voice filter, digital TV, music synthesizer • DSP features • Several instruction execution units • Multiple-accumulate single-cycle instruction, other instrs. • Efficient vector operations – e.g., add two arrays • Vector ALUs, loop buffers, etc.

  15. Selecting a Microprocessor • Issues • Technical: speed, power, size, cost • Other: development environment, prior expertise, licensing, etc. • Speed: how evaluate a processor’s speed? • Clock speed – but instructions per cycle may differ • Instructions per second – but work per instr. may differ • Dhrystone: Synthetic benchmark, developed in 1984. Dhrystones/sec. • MIPS: 1 MIPS = 1757 Dhrystones per second (based on Digital’s VAX 11/780). A.k.a. Dhrystone MIPS. Commonly used today. • So, 750 MIPS = 750*1757 = 1,317,750 Dhrystones per second • SPEC: set of more realistic benchmarks, but oriented to desktops • EEMBC – EDN Embedded Benchmark Consortium, www.eembc.org • Suites of benchmarks: automotive, consumer electronics, networking, office automation, telecommunications

  16. General Purpose Processors

  17. FSMD Reset PC=0; IR=M[PC]; PC=PC+1 Fetch Decode from states below Mov1 RF[rn] = M[dir] to Fetch op = 0000 Mov2 M[dir] = RF[rn] 0001 to Fetch Mov3 M[rn] = RF[rm] 0010 to Fetch Mov4 RF[rn]= imm 0011 to Fetch Add RF[rn] =RF[rn]+RF[rm] 0100 to Fetch Sub RF[rn] = RF[rn]-RF[rm] 0101 to Fetch Jz PC=(RF[rn]=0) ?rel :PC 0110 to Fetch Designing a General Purpose Processor

  18. Datapath 1 Control unit 0 To all input control signals RFs 2x1 mux RFwa Controller (Next-state and control logic; state register) RF (16) RFw RFwe From all output control signals RFr1a RFr1e 16 RFr2a Irld PCld PC IR RFr1 RFr2 PCinc RFr2e ALUs PCclr ALU ALUz 2 1 0 Ms 3x1 mux Mre Mwe Memory D A A Simple Microprocessor

More Related