1 / 19

Determination of the Molar Volume of Hydrogen Gas

Determination of the Molar Volume of Hydrogen Gas. Purpose. To determine the volume of one mole of hydrogen gas at standard conditions. Concept. Molar Volume is the volume occupied by one mole of a gas at standard conditions. (Theoretically 22.4 liters per mole.)

ramona
Télécharger la présentation

Determination of the Molar Volume of Hydrogen Gas

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Determination of the Molar Volume of Hydrogen Gas

  2. Purpose • To determine the volume of one mole of hydrogen gas at standard conditions.

  3. Concept • Molar Volume is the volume occupied by one mole of a gas at standard conditions. (Theoretically 22.4 liters per mole.) • The student should describe an application of this concept.

  4. Safety Name H F R Special Mg Ribbon 2 3 2 Flammable metal 6M HCl 3 0 3 Extreme Corrosive

  5. Procedure • Use iron wool to polish approximately 5 cm of magnesium ribbon. Then accurately mass the sample of magnesium.

  6. Procedure.2 • With a 20 cm piece of thread, tie one end around the middle of the Mg ribbon and bend the Mg ribbon into a zig-zag pattern.

  7. Procedure.3 • Prepare a 600ml beaker two thirds full with tap water. The eudiometer tube assembly will be placed in this beaker later in the experiment.

  8. Procedure.4 • Prepare the eudiometer tube by placing 15 ml of 6M Hydrochloric acid (HCl) in the tube, then fill the tube to the top with distilled water, being careful to minimize the mixing of the acid.

  9. Procedure.5 • Quickly place the Mg ribbon in the top of the eudiometer tube and pinch the thread between the stopper and the wall of the eudiometer tube.

  10. Procedure.6 • With out letting in any air bubbles, invert the eudiometer tube assembly into the water bath; allowing the contents the ability to flow into the water bath.

  11. Procedure.7 Make and record observations. Notice the density currents caused by the ‘sinking’ HCl. It makes the solution look oily. Once the acid reaches the Mg it begins to produce H2 gas.

  12. Procedure.8 Record the volume of the gas produced. 44.61 ml (read at apex of meniscus)

  13. Procedure.9 Record the height of the water column, in millimeters, above the level of the water bath. 11.65cm high or 116.5 mm of water

  14. Procedure.10 Record the temperature and the atmospheric pressure.

  15. Calculations.1 • The pressure of the dry H2 gas must be calculated. • There are two corrections to be made. • The water vapor mixed in with the collected H2 must be corrected. • The pressure difference between the inside of the tube and outside the tube must be accounted for.

  16. Calculations.2 • The pressure in the tube is less than the pressure outside the tube • The difference in pressure can be calculated by dividing the difference in water levels expressed in mm of H2O by 13.6 because mercury is 13.6 times more dense than water. 116.6 mmH2O 1.00 mm Hg 13.6 mmH2O = 8.57 mmHg

  17. Calculation.3 • The total pressure inside the tube is the atmospheric pressure minus the water column pressure difference. 774.2 mmHg – 8.57 mmHg = 765.6 mmHg

  18. Calculations.4 • Because there is H2 and H2O in the tube, the pressure of the water vapor must be subtracted. • Look up the water vapor pressure for the temperature of the gas. • The vapor pressure of water at 22.7°C is 20.7 mmHg 765.6 mmHg - 20.7 mmHg = 744.9 mmHg

  19. Conclusion • A good conclusion includes • a summary • results • sources of error • describes an error propagation.

More Related