1 / 40

危險性之化學物質 Dangerous chemical properties

危險性之化學物質 Dangerous chemical properties. 爆炸性物質 explosive chemicals : 包括 (1) 硝酸酯類 ( 如硝化甘油,硝化纖維等 ); (2) 硝基化合物 ( 如三硝基苯,三硝基甲苯等 ); (3) 有機過氧化物 ( 如過氧化丁酮,過醋酸等 ) 。它們可能經由摩擦,衝擊或加熱,而造成爆炸的結果

rusty
Télécharger la présentation

危險性之化學物質 Dangerous chemical properties

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. 危險性之化學物質Dangerous chemical properties • 爆炸性物質explosive chemicals: 包括(1) 硝酸酯類 (如硝化甘油,硝化纖維等); (2)硝基化合物 (如三硝基苯,三硝基甲苯等); (3)有機過氧化物(如過氧化丁酮,過醋酸等)。它們可能經由摩擦,衝擊或加熱,而造成爆炸的結果 • 著火性物質self-igniting chemicals: 置於常溫空氣中,可能因為吸收濕氣absorbing moisture or in contact with water或接觸水,分解產生可燃氣體,同時發熱而著火。包括: (1)鹼金屬(K, Li, alkaline metal etc); (2)磷及其他化合物 (黃磷,硫化磷等); (3)璐珞類; (4)鈣化類 (CaC2, Ca3P2); (5)金屬粉 (Mg, Al); (6) 二氧化硫磺酸鈉

  2. 危險性之化學物質(2) • 氧化性物質oxidizing chemicals: 本身含有氧元素,單獨存在並無危險,但若與其他可燃物或還原性物質接觸if in contact with other combustible material or reducing chemicals,並遇到衝擊,摩擦或發火源時,就會發火爆炸。包括: 氯酸鹽,過氯酸鹽,無機過氧化物,硝酸鹽類,固體亞氯酸鹽,以及固體次氯酸鹽類。 • 引火性液體fire-inducing liquids: 係指常溫room temperature下可以蒸發,以火焰接近fire near-by就可引起燃燒ignite的液體物質,包括: (1)閃火點flash point below在-30oC以下者,如乙醚,汽油,乙醛,環氧丙烷,二硫化碳CS2; (2)閃火點在-30-0 oC間者,如正己烷hexane,苯,丁酮,環氧乙烷等; (3)閃火點在0-30oC間者,如甲醇,乙醇,二甲苯,乙酸戊酯; (4)閃火點在30-65oC間者,如煤油kerosene,松節油等

  3. 若干常見的氧化劑a few common oxidizing chemicals

  4. 危險性之化學物質(3) • 可燃性氣體combustible gases: 指大氣壓下1 atm,15oC時為氣體gas,具可燃性質,例如氫氣hydrogen,乙炔acetylene,乙烯,甲烷,乙烷,丙烷,丁烷等。 爆炸下限越低,或爆炸範圍越廣者wide range for explosion,危險性增加more danger。 • 其他危險物質others: 其他一切易形成高熱easy to release heat,高壓increase pressure或易引起火災,爆炸之物質。

  5. (溫度) 熱能 氧氧 (空氣) 燃料 (可燃物) 火災理論fire theory * 燃燒的三要素three basic elements,缺一不可all are needed。  於是也成為預防火災的重要方法methods to prevent fire,也就是避免此三要素同時存在avoid simultaneous existence of three elements!! Oxygen (air), fuel (combustible materials), heat (or temperature; ignition source)

  6. 溫度 氧 氣 燃 料 連鎖反應 燃燒的錐體原理pyramid for combustion  就是再加入連鎖反應這個項目adding chain reaction,但是連鎖反應並非容易直接控制not easy to control,所以預防之道仍以三要素為主要對象the other three are more important。

  7. 閃熾flash 溫度T 著火ignite 擴 展expansion 成growth長 衰退decay 時 間time 火災之成長與過程course of a fire

  8. * 表達出稀釋劑所帶來的效果effect of dilution

  9. LEL & UEL • LEL, UEL: lower (upper) explosive limit 爆炸下限,爆炸上限: 指在此濃度範圍內within this range,才會產生爆炸 • LFL, UFL: lower (upper) flammable limit 可燃上下限,其與爆炸上下限間的差距不明顯 * 下限: 表示至少需要此數量的可燃物minimum amount of fuel for combustion or explosion,以便維持持續的燃燒放熱,造成爆炸效果 * 上限upper limit: 表示如果高於此值時,空氣的量就不夠了not enough oxygen * 理論上,可以由化學反應式估算之 (但僅對碳氫化合物有效),e.g. CH4 + 2 O2 == CO2 + 2 H2O, 計量比條件下,CH4濃度約為9.5%  then LFL 約等於計量比時濃度的一半half stoichiometry,I.e. LFL = 4.9% (實驗數據為5%, very close)

  10. 混合物的LFL & UFL for mixtures • LFL mix = 1/[(yi/LFLi)]; 在此計算過程中,yi是將所有可燃氣體放在一起計算的摩爾分率; • UFL mix = 1/[(yi/UFLi)] • 範例example: 氣體混合物中含有0.7 vol% 己烷hexane,2.0 vol% 甲烷methane,以及0.6 vol%乙烯ethylene,計算其燃燒上下限 • 先計算各成分的yi  己烷/甲烷/乙烯分別為0.21/0.61/0.18  查出三者的LFL & UFL 數據  帶入前項公式  得到混合物的燃燒下限與上限分別為: 2.63 vol% & 13.7 vol%

  11. 一般實驗都用量甚少,溫度及壓力的變化,可作為燃燒或爆炸與否的指標experiment apparatus

  12. 一般隨著溫度的上升,可燃範圍多半都會擴大flammable range will enlarge with temperature

  13. 計算範例example • 例如估算處理可燃液體的最高溫度: 對象acetone Ans. Acetone LFL = 2.55%; 一般安全處理所容許的濃度allowable為25% of LFL safe handling concentration • 在一大氣壓下,2.55% & 0.64% 分別為19.38 mm Hg, & 4.85 mmHg • 欲使丙酮蒸汽壓to lower vapor pressure of acetone降到上述兩個值,其對應的溫度corresponding temperature分別為: (由熱力學資料估算) –21.3oC & -40.9oC • 丙酮飽和蒸汽壓: ln(P) = 19.36 – 4126.27/T (P in mmHg, T in oK) • 結論: 所需溫度太低temperature too low, cost too much,成本高不合算,所以改用惰性氣體稀釋法use inert to dilute,以降低濃度。

  14. MOC • MOC = minimum oxygen concentration 係指在LFL濃度下之燃料,以化學計量比stoichiometry ratio將之完全燃燒complete combustion所需要的氧濃度 • 由安全safety viewpoint觀點: 此即為儲存時的最高氧容許濃度maximum permissible oxygen concentration during storage • MOC = LFL x (O2/fuel) 計量比stoichiometry ratio • 範例: butane LFL = 1.9%  C4H10 + 6.5 O2 == 4 CO2 + 5 H2O  MOC = 1.9% x 6.5 = 12.4% • 如果系統內另有稀釋劑if inert exist,則將稍微影響此一slightly change this valueMOC數值

  15. MIE • MIE = minimum ignition energy 最低點燃能量,他多半在數個到十數個mJ範圍內 • 靜電static electricity may be sufficient to provide this energy經常可以提供此一範圍內的點燃能量 • MIE當然也會隨條件而異may change according to different condition(例如不同濃度下,所需點燃能量也略微不同) • 若干具體數據some examples: 甲烷 1 atm 0.29 mJ 丙烷 1 atm 0.26 mJ 庚烷 1 atm 0.25 mJ 氫氣 1 atm 0.03 mJ 玉米粉 0.3 mJ 鐵粉 0.12 mJ

  16. 閃燃(火)點flash point • 定義: 讓可燃液體flammable liquid to reach的蒸汽濃度達到LFL vapor所需的最低溫度lowest temperature,此為代表可燃液體的重要危害參數之一important parameter for safety concern • 實驗時,可採取open cup or closed cup方式,所以數據也隨之略有差異 • 範例: 估算n-octane閃燃點,其 LFL = 1.0%  I.e. 即為估算使其蒸汽壓到達0.01 atm 所需的溫度  由熱力學thermodynamic data資料,可查出約為58oF

  17. Open-cup; closed-cup 數據會略微不同result differ slightly  何者會比較低which one will be lower (easier to ignite)?

  18. 取自Process safety progress, 17(3), 176, 1998. Fuel + z O2 == products Flammability diagram

  19. Out of service fuel concentration: OSFC 燃料濃度要降到多低才可以讓空氣進來how low should the concentration be before letting air in?

  20. In service oxygen concentration: ISOC 空氣濃度要降到多低才可以讓燃料進來how low should air concentration be before letting fuel in

  21. 混合物的閃燃點flash point for mixture • 其估算公式equation for estimation為: 使(yi/LFLi) = 1.0 所需的溫度temperature • 範例: x1=0.6 n-octane (C8H18) + x2=0.15 n-nonane (C9H20) + x3=0.25 n-decane (C10H22),估算其閃燃點  計算程序為: 猜一個溫度guess a temperature,然後依照Raoult’s law (yi P = P vap,i xi)計算個別的蒸汽壓vapor pressure, 於是得到其氣相組成(yi), 在試算前式是否符合  於是猜下一個溫度,直到符合為止  本題答案: 70oF,表示一般的汽油組gasoline composition成在室溫around room temperature下就達到閃燃條件,危險!!

  22. 自燃溫度auto-ignition temperature • AIT; 表示溫度夠高sufficient high temperature時,無須外來的點燃能量no outside ignition source,就可以自行燃燒的溫度 • 在絕熱情況adiabatic condition下,可燃氣體combustible gas-空氣air mixture的混合物,當被壓縮時,溫度升高,有可能到達自燃溫度reach AIT,而發生災害 (空氣可能是雜質air may be impurity,而非故意加入的) • 所以此時需要冷卻cooling is necessary!! 壓縮可燃氣體時的必要步驟!!

  23. 自氧化 Auto-oxidation • 指可燃物combustible material slowly oxidized慢慢的被氧化,放熱release heat,但熱傳效果不佳,所以累積溫度逐漸升高temperature increase gradually,最後造成火災fire的後果。 • 例如蒸汽管路steam pipe的絕熱包裝insulation packing內,吸附了某些高分子adsorb some polymer; 破布上的油oil on rag; • 吸滿高分子(e.g. 有機溶劑)的某種助濾劑 (多孔物質porous adsorbent with oil molecules),棄置不管,也許某一天就突然自己燒起來may suddenly burn by itself

  24. 絕熱燃燒溫度adiabatic combustion temperature • 能量平衡energy balance: H rxn (at Tin) +  ni Cpi dT (from Tin to Tout) = 0 • T out即為燃燒後所能達到的最高絕熱溫度highest temperature after complete combustion • Cpi = ai + bi T + ci T2 + di/T ½ • 明顯的需要trial-and-error程序,以C4H10為例計算,結果得到燃燒絕熱溫度 = 2400oK,  此時體積膨脹Vf/Vi = nfTf/(ni Ti) = 8.43 !! 此 一倍數不低,應有爆炸explosion effect的效果 • 相當於Unconfined burning of vapor cloud

  25. 可燃液體分類classification of flammable liquids • Class 1: 在室溫下room temperature,其蒸汽壓低low vapor pressure,不容易燃燒not easy to fire • Class 2: 其閃燃點高,要較高的溫度才能達到其LEL, 可能引起池火possible to pool fire • Class 3: 其閃燃點靠近室溫,表面蒸汽濃度在LEL之上,容易形成池火easy to pool fire • Class 4: 在室溫下,其蒸汽壓vapor pressure higher than已經高於LEL, 但仍低於lower than 1 atm者,容易被點燃 • Class 5: 蒸汽壓過高,需冷藏者,可能形成火球fire ball • Class 6: 液化可燃氣體,引起火球甚或爆炸者 • 再往上就是可燃性氣體next is flammable gases了

  26. 範例examples • Class 1: 潤滑油lubricant • Class 2: p-xylene, 閃燃點40oC, • Class 3: octane, 閃燃點 13oCmajor component of gasoline • Class 4: diethyl ether, 閃燃點 –45oC, 也容易造成閃火,10公尺以外就容易點燃can be ignited 10 m away • Class 5: LNG, 閃燃點 < -160oC, 100公尺外就容易點燃 • Class 6: propylene, 閃燃點 –107oC, 容易形成火球,100公尺外就能點燃 • 壓縮可燃氣體compressed flammable gas: ethylene

  27. Partition factor • 係指可燃液體flammable liquid,自其容器內外洩後after leak out,會有多少比例氣化之意fraction to vapor。 • 相當equivalent to 於flash distillation (under adiabatic condition)的計算,也就是input energy能量 = output能量 (氣化需要熱量gasification) • 氣化量高fraction high,則形成 easy to form vapor cloud蒸汽雲,危害性自然比較大。

  28. 火球fire ball: 乙烯,丙烷  閃火區flash fire: diethyl ether 分配partition factor係數  池火區pool fire: octane, xylene 閃火溫度flash temperature

  29. 火災危害等級與閃點範圍關係fire hazard classification and flash point 危害等級type 4: 閃點低於23oC, 且沸點低於38oC者; 等級type 3: 閃點低於23oC, 但沸點高於38oC者,或閃點在23-38oC間者 其他等級如圖as shown in figure 閃燃點flash point 沸點boiling point

  30. 火災的形式forms of fire • Pool fire池火: 外洩的可燃液體flammable liquid造成 • Fire ball: 火球,rich vapor cloud造成,表示大量洩漏 • Chemical conflagration: 化學大火 • BLEVE: boiling liquid expanding vapor explosion, 含可燃液體容器被燒,因而造成內部液體沸騰internal liquid boiling,產生蒸汽produce vapor,最後導致爆炸lead to explosion • Anaerobic fire: 厭氧性火災: 黑火藥black powder,固體推進劑之類的東西造成, nitrocellulose, ammonium nitrate

  31. 池火pool fire的示意圖 火焰的appearance (煙smoke,亮度shinny): 受風wind,flame speed, burning rate (物種material),radiative flux等影響。

  32. BLEVE: boiling liquid evaporating vapor explosion From Marshall

  33. 閃燃Flashover及燃爆Backdraft • 以下幾張圖片, 取自環保署南區毒災應變諮詢中心簡訊, 94年5月號 • 此二種狀況these two situations may cause serious damage to rescuers對救災人員可能造成重大傷害 • 預防之道prevention: 改採防火難燃材料fire-retardant materials; 自動滅火系統automatic fire fighting system; 破門破窗時when break window, 應站在側邊stay by the side, 避免正對門口instead of facing it

  34. 火災的另一傷害another damage from fire: 中毒poison • 主要因為燃燒burning會釋放出許多有毒氣體release many toxic vapors,因而造成中毒的結果。 • 可能產生的有毒氣體possible toxic gases包括: 一氧化碳 CO; 二氧化碳 CO2; 氰化氫 HCN (塑膠plastics,皮革leather,橡膠rubber,毛料wool,木材wood等); 氯化氫HCl; 硫化氫H2S; 二氧化硫SO2; 氮氧化物NOx; 氨NH3(木材,毛料等); 醋酸(多來自木材,紙張paper); 丙烯醛; 金屬煙; 燻煙(fumes)(燃燒不完全的產物incomplete combustion)

  35. 熱輻射的人體效應radiation effect on human body • 效應包括: 可能引起衣服燃燒cloth burning; 皮膚skin被灼傷(火災對人體的傷害之一) • 灼傷分類degree: 一級1st,二級2nd,三級3rd; 分別代表表皮surface ,中層皮膚medium ,以及深度deep皮膚組織受到傷害。 • Cold burn: 指被液態氮liquid nitrogen之類的東西接觸到,引起的效應; 冷灼傷 • 灼傷範圍大於affected area greater than 2.5 cm2, 都應該立即去看醫生see a doctor • 沖,脫,泡,蓋,送五步驟,應付燙傷。

  36. 燙傷處理小常識general sense • 未破皮者skin not off: 沖水flush with water後(10-15 min直到沒有痛until no pain feeling的感覺), 用很厚的鹽(cover with thick layer of salt)覆蓋, 再用濕的面紙覆蓋 (wet tissue偶而加水) – from some webpage KiWi • or 燙傷部位沉浸在冰鹽水中soaked in iced salt water

More Related