1 / 41

Ch.2 Intro. To Assembly Language Programming

Ch.2 Intro. To Assembly Language Programming. From Introduction to Embedded Systems: Interfacing to the Freescale 9s12 by Valvano, published by CENGAGE. 2.1 Binary and Hexadecimal Numbers. Decimal numbers {0,1,2,…,7,8,9} A decimal number is a combination of digits multiplied by powers of 10

sakina
Télécharger la présentation

Ch.2 Intro. To Assembly Language Programming

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Ch.2 Intro. To Assembly Language Programming From Introduction to Embedded Systems: Interfacing to the Freescale 9s12 by Valvano, published by CENGAGE

  2. 2.1 Binary and Hexadecimal Numbers • Decimal numbers • {0,1,2,…,7,8,9} • A decimal number is a combination of digits multiplied by powers of 10 • 1984 = (1)x103 + (9)x102 + 8 x101 + (4)x100 • Binary numbers • {0,1} • A binary number is a combination of binary digits multiplied by powers of 2. • 011010102 = %01101010 • 0x27+1x26+1x25+0x24+1x23+0x22+2x21+2x20 • = 0 +64 +32+0+8+2+0= 106

  3. 2.1 Binary and Hexadecimal Numbers (cont.) • Hexadecimal numbers • {0,1,…9,A,B,C,D,E,F}, where A=10, …, F=15 • A hexadecimal number is a combination of the digits {0-F} multiplied by powers of 16 • 12AD16 = $12AD = 1x163 +2x162 +(10)x161 +(13)x160 = 4096 + 512 + 160 +13=4781 • Fractions—use negative powers. • Words=16 bits on the 9s12. • Bytes = 8 bits on the 9s12. • Nibble = 4 bits.

  4. Checkpoints • Checkpoint 2.1 What is the numerical value of %11111111? • Checkpoint 2.2 What is the numerical value of $FF? • Checkpoint 2.3 Convert the binary number %01000101 to hexadecimal. • Checkpoint 2.4 Convert the binary number %110010101011 to hexadecimal. • Checkpoint 2.5 Convert the hex number $40 to binary • Checkpoint 2.6 Convert the hex number $63F to binary. • Checkpoint 2.7 How many binary bits does it take to represent $123456?

  5. 2.2 Addresses, Registers, and Accessing Memory • Figure 2.3—memory model of simplified 9S12 computer (small boxes—8 bits) • Address—specifies the location from where to read data to where to write data. • Addresses—simple linear sequences—from $0000 to $FFFF. • $0240 points to an I/O port (Port T) • $3800 points to a location in RAM • $F004 points to a location in EEPROM

  6. Registers • Registers—high speed storage devices located in the processor. • Registers do not have addresses, but instead have names and numbers. • Register A (8 bits) • Program Counter (PC)—16 bits—contains the address of the instruction that is executing.

  7. Read/Write Operations • For this text (see page 30) • =[U] specifies an 8-bit read from address U. • ={U} specifies a 16-bit read from addresses U, U+1 (most significant byte first). • [U]= specifies an 8-bit write to address U. • {U}= specifies a 16-bit write to addresses U, U+1 (most significant byte first).

  8. Checkpoint • Checkpoint 2.8: What does [$0240] = RegA mean literally? What is the overall action?

  9. Registers of the 9S12 • Fig. 22.4 shows the six registers (page 30 of text). • Accumulator—typically used to hold and manipulate numbers—RegA and RegB (8 bits each or 16 bits when combined –RegD) • Index Registers —RegX and RegY –16 bits each—addresses and pointers. • Program Counter (PC)—points to the current instruction and is 16 bits. • Condition Code Register (CC or CCR)—8 separate bits—S, X, H, I, N, Z, V, C—Z is set of the result is zero after an operation.

  10. CLI • The I bit can be cleared using the CLI instruction during the debugging of a program. • More in Chapter 9.

  11. Checkpoint • Checkpoint 2.9 (page 31): Think about how you could use the “subtract” and the “branch on zero” instructions to test if two numbers are equal?

  12. Stack Pointer Register • The stack is temporary storage in RAM. • SP is a 16-bit register that points to the top of the stack. • Figure 2.5 illustrates the process of “pushing” on the stack (the SP is decremented and the data is written.) • To “pop” data, the data is read from the location specified by SP, then SP is incremented.

  13. Memory Maps • Table 2.2—9S12C32 • Table 2.3 9S12DPS12 • Table 2.3 9S12E128

  14. 2.3 Assembly Syntax • 2.3.1 Assembly Language Instructions • Load AccumulatorA : ldaa • Reads an 8-bit byte and places it into register A. • Assembly code fields • Label opcode operand comment • Here ldaa $3800 ; RegA= $3800

  15. Assembly Code and Machine Code • Assembly language instructions, assembly code, assembly source code • Machine instructions, machine code, and object code (can be loaded into EEPROM and executed.) • Example: • Assembly code: ldaa $3800 • Machine code: $B6, $38, $00 • An assembler converts the assembly language program into machine code.

  16. 2.3.2 Pseudo Operation Codes • Pseudo-op, pseudo operation code, and assembly directives are equivalent. • These are used by the assembler during the assembly process and are not executed as assembly code. • Example: • org $4000 means that the machine code will be loaded into EEPROM memory starting at location $4000.

  17. More Pseudo Codes • equate is used to define a symbol. • Reserve multiple bytes (rmb) is used to define uninitialized variables. • Form double byte (fdb) is used to form a 16 bit constant. The following two lines indicate where to start execution: • org $FFFE • fdb main

  18. Consider the following: org $8080 Ptr1 rmb 2 Data1 rmb 1 Ptr1 is found at $8080 and $8081. Checkpoint 2.10 Where in memory will the variable Data1 be located? Hint: it comes after Ptr1; it is not in $8080. Checkpoint

  19. 2.4 Simplified 9S12 Machine Language Execution • A simplified cycle-by-cycle analysis is done. • TExaS can simulate both the hardware devices and software action at the same time. • Table 2.5 (page 34) illustrates the difference between a real 9S12 and the TExaS bus cycle simulation.

  20. Components of the 9S12 • See Figure 2.6 (page 34). • Control Unit (CU) —controls the sequence of operations. • Instruction Register (IR) —contains the op code of the current instruction. • Arithmetic Logic Unit (ALU) —performs addition, subtraction, multiplication, division, and, or, and shift. • Bus Interface Unit (BIU) —reads and writes data to the bus. • Effective Address Register (EAR) –contains data address for the current instruction –TExaS allows the EAR to be observed. • Bus—8 bits and 16 bits (R/W is the control). • Memory • I/O Ports

  21. Read and Write Cycles • Read Cycles • Instruction fetch —PC points to data to be placed in the IR. • Operand fetch — effective address is calculated. • Data fetch –the address is in the EAR, and data is placed in a register or sent to the ALU, • Stack pull -- data is “popped” from the stack. • Write Cycles • Data write (from a register or ALU to memory location stored in the EAR) • Stack push

  22. Phases of Execution (page 35 of text) • Phase 1: Opcode and Operand fetch • Phase 2: Decode instruction • Phase 3: Evaluate address • Phase 4: Data read • Phase 5: Free cycles • Phase 6: Data write

  23. Simple Address Modes • Inherent Addressing • Immediate Addressing • Direct (Page) Addressing—other computers call this zero page addressing. • Extended Addressing—other computers call this direct addressing. • Indexed Addressing • PC Relative Addressing

  24. Addressing Modes • 2.5.1 Inherent Addressing Mode • There is no operand field. • Example: clra (machine code $87) • Figure 2.7 The data for the instruction is implied—RegA is set to zero. • 2.5.2 Immediate Addressing Mode • The data is included in the machine code. • Example ldaa #36 (machine code $86 $24) • Figure 2.8—phase 1: fetch opcode; phase 2 fetch operand.

  25. Addressing Modes • 2.5.3 Direct (Page) Addressing • Uses an 8-bit address to access location from 0 to $00FF (some addresses are I/O ports) • Example: ldaa $32 (machine code: $96 $32) • Figure 2.9 –opcode is read; operand is read; value of Port K ($32) is $57; $57 is placed in register A. • 2.5.4 Extended Addressing • Uses a 16-bit address; allows access to all memory and I/O. • Example: ldaa $3800 (machine code: $B6 $38 $00 • Figure 2.10 --opcode is read; operand is read; rest of operand is read; address is calculated and data is moved into register A.

  26. Addressing Modes • 2.5.5 Indexed Addressing • Uses a 16-bit pointer in a register to access memory and I/O devices. • RegX and RegY can be used as the pointers. • Example: ldaa 0,x (machine code: $A6 $00) • Figure 2.11—opcode is fetched; operand is fetched; fetch using the EAR, the data in $3900. • 2.5.6 PC Relative Addressing • Used for the branch and branch to subroutine instructions. • Example: bra main (machine code $20 $F4) • Fig. 2.11—opcode is fetched; operand is fetched. • The operand field for PC relative addressing is an 8-bit value called rr. • rr = (destination address) – (location of instruction) – (size of the instruction).

  27. Checkpoints • Checkpoint 2.12: What is the difference between ldaa #36 and ldaa #$24? • Checkpoint 2.13: What is the difference between ldaa #32 and ldaa $32? • Checkpoint 2.14: Give the machine code for the assembly code that branches to itself, causing an infinite loop, loop braloop

  28. 2.6 The Assembly Language Development Process • An editor is used to create the source code. • An assembler is used to translate the source code to machine instructions. • The assembler also produces a listing file, which shows the addresses and object code that corresponds to each lin of the assembly code. • A loader is used to place the object code into memory, when a real microcontroller is used.

  29. 2.7 Memory Transfer Operations (page 41 of text) • Symbols used • w—signed 8-bit (-128 to + 127) or unsigned 8-bit (0-255) • n -- signed 8-bit • u – unsigned 8-bit • W -- signed 16 bit (-32787 to + 32767) or unsigned 16- bit (0 to 65535) • N -- signed 16-bit • U -- unsigned 16-bit

  30. Instructions for Memory Transfer(page 42) • Note that copies are made of the memory contents. • Instructions: • Load (memory contents are copied into a register.) • Move (copies of memory values are moved into other memory locations.) • Store (register contents are copied and moved into memory.)

  31. Checkpoints • Checkpoint 2.15: What is the difference between ldx #$0801 and ldx $0801? • Checkpoint 2.16: What is the difference between direct mode instruction ldx<$12 and the extended mode instruction ldx>$0012? • Checkpoint 2.17: Write assembly code that copies the 8-bit data from memory location $0810 to memory location $0820. • Checkpoint 2.18: Write assembly code that writes the binary %11000111 to Port T.

  32. 2.8 Subroutines • Subroutines are subprograms that may or may not return a value (text—page 43). • Program 2.1 (page 43) Subroutine Set • Command bsr is used (but jsr could also be used.) • Relative addressing is used with bsr and extended addressing is used with jsr. • At run time, the return address will be pushed on the stack, and then will be pulled when the subroutine is finished (instruction rts is used.) • Two global variables: Flag and Data • Fig. 2.13 illustrates the stack during execution.

  33. 2.9 Input/Output • 2.9.1 Direction Registers • PTT—8-bit Port T—address $0240. • Each of the eight pins can be an input (logic levels.) • Fig. 2.15—illustrates the direction register DDRT. • If DDRT = $FF all pins are outputs. • If DDRT = $00 all pins are inputs. • If DDRT = $0F PT0-PT3 are outpus; others are inputs.

  34. Checkpoint • Checkpoint 2.19: What happens if we were to set DDRT ro $F0?

  35. Example 2.1 (page 46 of text) • Make PTT pins 7-4 input and pins 3-0 output, then make PT3-PT0 output high. • Set the direction register: • ldaa #$0F • staa DDRT • Set the outputs high • ldaa #$0F • staa PTT

  36. 2.9.2 Switch Interface • SPST—single poll single throw • Figure 2.16 (page 47). • Mechanical switches is subject to bouncing—this can be reduced by reading the value and then waiting 10ms before reading again.

  37. 2.9.3 LED Interface • LEDs emit light when electric current passes through them. • The current must pass from the anode to the cathode. • The cathode is the short lead. • Figure 2.17 (page 47). • Suppose the desired brightness requires 1.9V. • R = (5 –Vd-Vol)/Id = (5-1.9-.5)/.01 = 260 ohms. • Vd is the desired operating voltage. • Vol is the ouput low voltage of the LED driver. • Id is the desired LED current.

  38. Checkpoint • Checkpoint 2.20: What resistor value in Figure 2.17 is needed if the desired LED operating point is 1.7 V and 5 mA?

  39. LEDs (cont.) • The driver is not needed when the LED current is much less than 10 mA. • Figure 2.18 (page 48) illustrates this situation for LED interfacing. • Positive logic interface: R = (Voh – Vd)/Id. • Negative logic interface: R = (5-Vd-Vol)/Id.

  40. Checkpoint • Checkpoint 2.21: What resistor value in Figure 2.18 is needed if the desired LED operating point is 1.7V and 2 mA?

  41. Example 2.2 (page 48-49) • Build a system with three LEDs that flash a rotating sequence 100,010,001 over and over. • Use low current LEDs (cheaper and easier to interface). • Use PT0-PT2 as the three output pins. • As shown in Figure 2.18, build three positive logic LED circuits as shown in Figure 2.19. • Software is shown on pages 49 and 50.

More Related