1 / 65

The research about power control in Our LAB

The research about power control in Our LAB. 2003, 07, 23. Introduction. Single-Channel MAC Protocol with Busy Tones and Power Control (2000) Multi-Channel MAC Protocol with Power Control (2001) Increasing the Throughput of Packet Radio Networks with Power Adjustment (2001)

timothy-mendez
Télécharger la présentation

The research about power control in Our LAB

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. The research about power control in Our LAB 2003, 07, 23

  2. Introduction • Single-Channel MAC Protocol with Busy Tones and Power Control (2000) • Multi-Channel MAC Protocol with Power Control (2001) • Increasing the Throughput of Packet Radio Networks with Power Adjustment (2001) • Power-Aware Routing for Energy Conserving and Balance in Ad Hoc Networks (2002) • Energy-Conserving Grid Routing Protocol in Mobile Ad Hoc Networks (2002)

  3. Single-Channel MAC Protocol with Busy Tones and Power Control 吳世琳 2000

  4. Goal • Contributions: • Increasing channel Utilization • Saving battery energy • Combining power control, RTS/CTS-basedand busy-tone-basedprotocols together

  5. Some important terms • Hidden-terminals • Exposed-terminals • Traffic load • Throughput • End-to-End Delay

  6. A B C D A B C

  7. Review of some MAC protocols • CSMA/CA (Carrier Sense Multiple Access/Collision Avoidance) • RTS/CTS-based protocols • RTS/CTS dialogue Enhanced with Busy Tones • A New MAC Protocol with Power Control

  8. CTS-2 CTS-1 RTS-2 RTS-1 CTS-2 CTS-1 CTS-1 RTS/CTS-based protocols D C E B A

  9. RTS/CTS dialogue Enhanced with Busy Tones • DBTMA (Dual busy Tone Multiple Access) • Single common channel is split into data and control channels • Narrow-band busy tone: • Transmit Busy Tone (BTt) and Receive Busy Tone (BTr) BTt BTr Control channel Data channel Frequency

  10. RTS/CTS dialogue Enhanced with Busy Tones • BTt : a host is transmitting • BTr :a host is receiving • A sending host must turn BTt on when transmitting data packets • A receiving host must turn BTr on when it replies a CTS • A host wants to send a RTS: check BTr • A host want to reply a CTS: check BTt

  11. CTS-2 +BTr CTS-1 +BTr RTS-2 RTS-1 CTS-2 +BTr CTS-1 +BTr CTS-1 +BTr RTS/CTS dialogue Enhanced with Busy Tones D C E B A

  12. D D C C E E B A B A F F A New MAC Protocol with Power Control

  13. A New MAC Protocol with Power Control • To use the exchange of RTS/CTS packets to determine power level • Power levels: • Pmax : the maximum transmission power • Pmin : the minimum power level • Pnoise : a power level regarding a signal as a noise

  14. A New MAC Protocol with Power Control • Transmission Power • Signal Strength • Tuning Power Levels: • Pr = Pt (  / 4d )n gt gr • Pmin = PCTS (  / 4d )n gt gr • Pmin / Pt = PCTS / Pr • : carrier wavelength, d: distance, g :antenna gains

  15. A New MAC Protocol with Power Control • HostX intends to send a RTS to HostY use power level PX • If no receiving any busy tone, then PX = Pmax • Otherwirse, PX = Pmax * Pnoise / Pr (Pr is the power level of the highest power among all BTr) • HostY receives HostX’s RTS • If there is any busy tone, Then HostY ignore RTS • Otherwise, HostY replies CTR with Pmax and turn on BTr at Pmax

  16. A New MAC Protocol with Power Control • When HostX receives CTS, • turning on BTt and transmitting data packets • PX = Pmin * Pmax / Pr (Pr is the power level of CTS)

  17. P.S. • Performance Analysis (read by yourself) • Simulation results (read by yourself)

  18. Multi-Channel MAC Protocol with Power Control 吳世琳 2001

  19. Multi-channel MAC Protocols • Channel assignment • Assigning channel to user • Medium access • Resolving the contention/collision problems

  20. DCA-PC (Dynamic Channel Assignment with Power Control) • Feature • Dynamically channel assignment (RTS/CTS/RES) • Independent of the network size, topology, and degree • Clock synchronization is not necessary • Channel model • One control channel • N data channels D1, D2, D3, …, Dn

  21. DCA-PC (Dynamic Channel Assignment with Power Control) • Hosts is equipped with two half-duplex transceiver • Control transceiver • Data transceiver • Data structures • CUL[i]: Channel Usage List • POWER[i]: the power level using to send

  22. DCA-PC (Dynamic Channel Assignment with Power Control) D A C F B E

  23. Increasing the Throughput of Packet Radio Networks with Power Adjustment 黃啟富 2001

  24. PRN (Packet Radio Networks)

  25. Simple simulation result

  26. Solution for SAPA – distance-based scheme • Each host has a common power (Pi) and a code (ci) • Increasing the powers of individual stations to increase the network connectivity • Under the constraint, that no primary and secondary collision should occur

  27. Solution for SAPA – distance-based scheme • L: the list of all station pairs (i,j) • Link (i,j)  G and (dist(i,j)) • Sort L in an ascending order of the distance • Collision array (col [i ]): the set of codes used by the host and it’s neighbors • col [i ] = {ci}  { cj | (i,j)  G }

  28. Solution for SAPA – distance-based scheme • Pick 1st entry (i,j) of L •  k : -1 (Pi) < dist(i,k)  dist(i,j)  ci col [k] •  k : -1 (Pj) < dist(j,k)  dist(i,j)  ci col [k] • Both condition hold, adding link (i,j) will no suffer from primary and secondary collision • If so, changing the power setting and update collision array • Remove (i,j) from L and if L is not empty goto step 3

  29. Solution for SAPA – distance-based scheme Original Link F2 Bidirectional Link H4 Unidirectional Link E2 G3 C1 A3 D1 B5

  30. Power-Aware Routing for Energy Conserving and Balance in Ad Hoc Networks 賴正偉 2002

  31. Goal • Reducing power consumption in transmission • A route consists of larger remaining energy hosts and accumulatively consumes less transmission power is considered as a better one

  32. Choose a suitable transmission power

  33. A A H Ptk-1 H Ptk H H Region K Region K Change transmission power

  34. Cost Function • Bi(0): the initial energy of hosti • Bi(t): the remaining energy of hostj at time t • Rbi : remaining energy ratio • Pij : the transmission power used by hosti to send packets to hostj • Ri(t) : remaining transmission time

  35. Cost Function • Cost = x Pij

  36. PCSR – route discovery B(0.8) D(0.7) source A(0.9) destination C(0.9) F(0.8) E(0.6)

  37. PCSR – route discovery B(0.8) D(0.7) (0,0.9,-1,”A”) A(0.9) C(0.9) F(0.8) HostA broadcast route request packet E(0.6)

  38. PCSR – route discovery • Assume Pt1 is 0.3 W, Pt2 is 0.2 W, Pt3 is 0.1 W • All hosts have initial energy 100 W 0.2/0.9 90/0.2 B(0.8) (0.22,0.8,450,”A,B”) Pt2 D(0.7) A(0.9) C(0.9) F(0.8) HostB broadcast route request packet E(0.6)

  39. PCSR – route discovery B(0.8) D(0.7) A(0.9) Pt1 (0.33,0.9,300,“A,C”) C(0.9) F(0.8) E(0.6) HostC broadcast route request packet

  40. PCSR – route discovery B(0.8) Pt2 D(0.7) (0.47,0.7,400,“A,B,D”) A(0.9) 0.22+0.25 C(0.9) F(0.8) E(0.6) HostD broadcast route request packet sent by HostB

  41. PCSR – route discovery B(0.8) D(0.7) A(0.9) (0.44,0.7,300.“A,C,D”) Pt3 C(0.9) F(0.8) E(0.6) HostD broadcast route request packet sent by HostC

  42. PCSR – route discovery B(0.8) D(0.7) A(0.9) Pt3 C(0.9) F(0.8) E(0.6) (0.44,0.6,300,“A,C,E”) HostE broadcast route request packet

  43. PCSR – route discovery B(0.8) (0,22,0.8,450,”A,B”) (0,0.9,-1,”A”) D(0.7) (0.47,0.7,400,“A,B,D”) A(0.9) Pt3 (0.61,0.8,400,“A,B,D,F”) C(0.9) F(0.8) E(0.6) HostF receives the first route request packet and then wait until Wreq elapsed

  44. PCSR – route discovery B(0.8) D(0.7) (0.33,0.9,300,“A,C”) (0.44,0.7,300,“A,C,D”) A(0.9) Pt3 (0,0.9,-1,”A”) (0.58,0.8,300,“A,C,D,F”) C(0.9) F(0.8) E(0.6) HostF receives the second route request packet

  45. PCSR – route discovery B(0.8) D(0.7) A(0.9) (0.60,0.8, 300,“A,C,E,F”) (0,0.9,-1,”A”) Pt3 C(0.9) F(0.8) (0.33,0.9,300,“A,C”) E(0.6) (0.44,0.6,300,“A,C,E”) HostF receives the third route request packet

  46. PCSR – route discovery B(0.8) D(0.7) A(0.9) C(0.9) F(0.8) E(0.6) (0.60,0.8, 300,“A,C,E,F”) HostA receives route reply packet and starts to send packets to HostF

  47. Energy-Conserving Grid Routing Protocol in Mobile Ad Hoc Networks 胡政達 2002

  48. Goal • Our motivation is to design a energy-conserving routing protocol • Reduce the hosts’ energy consumption when idle • Prolong the lifetime of whole network • Maintain good packets delivery quality

  49. Power consumption • Power consumption of Lucent IEEE 802.11 WaveLan card • A mobile host still consumes much energy even when idle

  50. Geography-informed energy conservation for ad hoc routing (GAF) • The geographic area is partitioned into grids • In a grid, one mobile host is active and others can sleep • A host will set the sleeping duration before if goes to sleep • After this period of sleep, the host will wake up to check its activity • No way to ensure that a destination host is active when packets are sent to it

More Related