200 likes | 595 Vues
Outline. PurposeSolutionsSolution Preparation from SolidsSolution Preparation from Liquids (dilution)ElectrolytesConductivityProcedureWasteWhat to turn inSpring BreakNext Assignment. Purpose. To illustrate the behavior of strong, weak, and non-electrolytes in aqueous solution.Achieved th
E N D
1. Experiment 5 Solutions, Electrolytes, and Conductivity
2. Outline Purpose
Solutions
Solution Preparation from Solids
Solution Preparation from Liquids (dilution)
Electrolytes
Conductivity
Procedure
Waste
What to turn in
Spring Break
Next Assignment
3. Purpose To illustrate the behavior of strong, weak, and non-electrolytes in aqueous solution.
Achieved through the use of electrical conductivity measurements.
Solution preparation practice.
4. Solutions Be able to distinguish between:
Dissolution: a solid, liquid, or gas is dissolved in a solvent
Dissociation: the breakup of compounds into simpler components, such as the dissociation of ionic compounds into ions
Types of solutions we are dealing with today:
solid to liquid
liquid to liquid
5. Solution Preparation When you are required to make a solution of accurate concentration and volume, a volumetric flask is used.
We never make solutions of accurate concentration in:
Beakers
Graduated cylinders
Erlenmeyer flasks
6. Solution Preparation from Solids Determine the mass of the solid needed by using:
Molar mass of the solid
Total volume desired
Final concentration desired
Calculation:
Mass, g = [ ], mol/L x MM, g/mol x Vol, L
Remember the precision of your glassware!
7. Solution Preparation from Solids Make the solution:
Weigh out the appropriate mass of solid.
Place a small volume of distilled water in the volumetric flask.
Add the solid to the volumetric flask.
Add some more distilled water to the flask, stopper, and invert several times.
Add distilled water to the calibration line (fill to volume) using a medicine dropper, stopper, and invert several times.
8. Solution Preparation from Liquids Determine the volume of stock solution needed by using:
Concentration of stock solution (M1)
Desired concentration of diluted solution (M2)
Desired volume of diluted solution (V2)
Calculation:
M1V1 = M2V2
Remember the precision of your glassware!
9. Solution Preparation from Liquids Make the solution:
Obtain the appropriate volume of stock solution using a graduated cylinder. (Always add a few mL extra.)
Place a small volume of distilled water in a volumetric flask.
Use the appropriate pipet to transfer the correct volume of stock solution from the graduated cylinder to the volumetric flask.
Add some more distilled water to the flask, stopper, and invert several times.
Add distilled water to the calibration line (fill to volume) using a medicine dropper, stopper, and invert several times.
10. Electrolytes Strong Electrolytes
100% dissociation and high conductivity
NaCl(s) ? Na+(aq) + Cl-(aq)
Weak Electrolytes
partial dissociation and partial conductivity
CH3COOH(aq) ? CH3COO-(aq) + H+(aq)
Non Electrolytes
no dissociation and no conductivity
C12H22O11(s) ? C12H22O11(aq)
11. Conductivity The ability of an aqueous solution to conduct electricity is dependent on the presence of ions in solution.
Conductivity or K has units of S/cm, mS/cm, or ?S/cm.
We measure conductivity so we can make a comparison regarding relative numbers of ions present in solution.
12. Conductivity The extent to which a solution conducts electricity is dependent on the proportional amount of ions present in solution.
Which of the following will have a higher conductivity?
NaCl vs. CaCl2 Why?
NaCl vs. C6H5COOH Why?
13. Procedure Soak your conductivity probe in distilled water for 30 minutes before starting your experiment. Why?
Calibration
14. Procedure Any glassware that will be containing non-electrolytes or weak electrolytes need to be rinsed thoroughly with distilled water prior to use!!!
Make up your three known solutions.
Measure the conductivities of your known solutions, distilled water, tap water, and three unknowns.
The unknowns are already at the required concentration. No dilution is necessary!
15. Reagents:
Acetic Acid (3%)
KCl
NaCl
Sucrose
Eye Contact:
Irritation, redness, pain, and possible damage
Skin Contact:
Irritation. May cause sensitization and / or allergic reaction. Absorption may cause symptoms similar to ingestion
Inhalation:
Irritation and coughing
Ingestion:
Gastrointestinal irritation, nausea, vomiting, diarrhea, prostration, dehydration and congestion of internal organs, and violent inflammatory reactions in the gastrointestinal tract
Safety Concerns
16. Waste All neutral solutions can go down the drain with plenty of water when you are finished.
Acidic solutions need to be disposed in the acid waste container in the fume hood.
Remember to clean up the balances and counters if / when you spill anything.
17. What to turn in When you are finished, confirm that your report is complete, then turn in the following:
Report sheet
Conductivity calibration curve
Complete and submit your post-lab questions by the deadline.
18. Spring Break There are no classes next week.
You may have assignments due. Be sure to complete and submit them by their respective deadlines.
19. Next Assignment Experiment 6 Read the required reading sections in your textbook and lab manual.
Complete and submit your pre-lab questions by the deadline.
If your class is required to complete quizzes in Blackboard, remember to do so.