1 / 143

OBD II UPDATE TRAINING COURSE

OBD II UPDATE TRAINING COURSE. OBD II Foundation OBD II History OBD II Terminology OBD I vs OBD II OBD II MIL Operation DTCs (A & B types. OBD II Numbering Rationality / Normality One/Two Trip DTCs Freeze Frame I/M Readiness Monitors. OBD II Module Outline. SESSION 1 OBD I FOUNDATION.

valentino
Télécharger la présentation

OBD II UPDATE TRAINING COURSE

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. OBD II UPDATE TRAINING COURSE

  2. OBD II Foundation OBD II History OBD II Terminology OBD I vs OBD II OBD II MIL Operation DTCs (A & B types OBD II Numbering Rationality / Normality One/Two Trip DTCs Freeze Frame I/M Readiness Monitors OBD II Module Outline

  3. SESSION 1OBD I FOUNDATION • Onboard Diagnostics Generation 2 • Not a stand alone system • OBD II is built on top of OBD I

  4. THE OBD I FOUNDATION • OBD I mandated a “Check Engine Light” • Included diagnostic trouble codes (DTCs)

  5. THE OBD I FOUNDATION • OBD I Mandated in 1988 • Objectives • Improve emission compliance by notifying the driver that there was a malfunction • Assist in identifying malfunctioning circuits in the computer control system

  6. OBD I MIL Operation • Check Engine Light Operation • Illuminated when circuit was abnormal • Open, Shorted, Grounded • Illuminated intermittently when circuit operated abnormally intermittently • Didn’t always illuminate when a problem was detected! • WAS INCONSISTENT!!!

  7. Serial Data • Live Computer Data • Supplied by the vehicle’s computer • Read via a Scan Tool • Interpreted Data • GM, Chrysler, then Ford • Now mandated by OBD II

  8. Diagnosing Today’s Vehicles • Technician must have a strong foundation in system operation & theory!!! • Technician must have ability to fully utilize today’s tools • Scan Tool, DSO, 5-gas analyzer, etc. • Technician must know how theory & tools are best applied together

  9. OBD I • On Board Diagnostics with a Check Engine Light • Mandated by CARB • Gave birth to OBD II

  10. OBD II Update Training Course Session II OBD II Foundation

  11. Session 1The OBD I Foundation • OBD I - On Board Diagnostics with a Check Engine Light • MIL Operation Inconsistent • DTC Viewing Method Inconsistent • DTC Criteria Inconsistent • DTC Numbering Inconsistent

  12. The OBD II System • The Second Generation was designed to fix the inadequacies of the First Generation • One of the biggest problems was the system must be monitored under load!

  13. OBD I Mode Monitoring • Degraded emission systems did not set Check Engine Light • EVAP, CAT, & AIR were not monitored • O2S Performance not monitored • CAT killing misfires not monitored • Shifted air fuel ratios not monitored • NOx emissions not monitored (still?)

  14. OBD II Strategies • Implementation slated for 1996 models • Phase in to begin 1994-1996 • OEMs allowed to EEPROM flash to lock-out problems affecting CSI • Check with manufacturer regarding current configuration

  15. Setting the Standards • C.A.R.B - 1994 - 1998 • E.P.A. 1998 - On • S.A.E. • Requirements for common systems • Programming changes

  16. OBD II Requirements • Must be installed on all vehicles • Must be able to determine operating condition of the vehicle’s emission control system / strategy • Diagnostics & Functions must be standardized

  17. OBD II Requirements • PCM must store DTCs for detected faults • DTC’s must stay in memory until cleared following repair or until 40 consecutive warm-up cycles • 80 consecutive warm-up cycles if misfire and/or fuel control related

  18. OBD II Requirements • The system must test emission control systems, record the results, and display those results • A MIL is mandatory • must illuminate when a fault is detected (and confirmed?) • must remain illuminated until the fault is corrected (3 tests)

  19. OBD II Requirements • Generic Scan Tool (GST) • SAE J 1850 and/or ISO 9141 communication protocol • Must monitor ALL OBD II information • Monitoring & DTC clearing procedures must meet CARB & EPA standards • Must display Parameter ID (PIDs) • Freeze Frame Data • PCM Parameters & Test Results

  20. OBD II Requirements • Monitor Test Results • Comprehensive Component Monitoring • Input Normality & Rationality • Outputs for performance or at least electrically

  21. The Scan Tool(2 Tools In One?) • OBD II Generic Scan Tool (GST) • Manufacturer Specific Scan Tool • Hybrid • OBD II Generic with Manufacturer Specific Capabilities

  22. OBD II Commonalties • Standardization Facilitated by SAE • SAE compromised of Reps from OEMs • OBD II guidelines established by SAE • OEMs interpreted guidelines differently • OBD II is the SAME, but DIFFERENT!

  23. Emission Related Monitoring • Unlike OBD I, OBD II not only monitors an actuator was commanded on, but tests the system to make sure it actually worked!!!

  24. OBD II Monitors • Designed to detect failures that would cause emissions to increase by 50% or would shorten the life of the catalytic converter • The number of monitors are increasing • Monitors require more computing resources and additional sensors • Monitors are run under specific conditions

  25. OBD II Program Management • Program Manager • Task Manager • Diagnostic Executive • OBD II Program Management • Artificial Intelligence • Rationality

  26. OBD II Standardization • Common Diagnostic Connector • Data Link Connector (DLC) • 16 pins -- 7 for SAE/OBD II & 9 for OEM • 1 pin is B+ to power Scan Tool • DLC to be located on drivers side near steering column or have a location label

  27. MIL Regulations • MIL will illuminate when an increase in emissions = to 1.5 X the FTP is inferred • Or when the PCM/Network itself malfunctions • The MIL shall not be used for any other purpose!!!

  28. MIL Operation • MIL On • a fault has been detected (and confirmed?) • MIL Off • No fault has been detected • Test have not been run • MIL Flashing • Catalyst damaging misfire or air fuel problem detected

  29. Diagnostic Trouble Codes • Common numbering system for all DTCs • Alpha Numeric • 5 digit • DTCs must be similar in meaning • DTC designation must be common • SAE standard J2012

  30. DTC Numbering • 1st Digit • Alpha Character • “P” - Powertrain • “C” - Chassis • “B” - Body • “U” - Uart / multiplexing / networking

  31. DTC Numbering • 2nd Digit or thousandth position • Either “1” or “0” • “0” Codes are SAE / OBD II Controlled • “1” Codes are Manufacturer Specific

  32. DTC Numbering • 3rd Digit or hundredth position • System Fault • “100” - Fuel & Air Metering • “200” - Fuel & Air Metering (injector & fuel pump) • “300” - Misfire or Ignition System • “400” - Emission Control

  33. DTC Numbering • 3rd Digit or hundredth position • System Fault • “500” - Vehicle Speed and/or Idle Control • “600” - Computer Output Circuits • “700” - Transmission • “800” - Transmission

  34. DTC Numbering • 4th & 5th Digits - tens & ones • Designate Specific Fault • Example • P0301 = Engine Cylinder # 1 Misfire Detected

  35. Diagnostic Trouble CodesOBD I vs. OBD II 1. OBD II requires “code enabling criteria” be met (maybe twice) before a code is stored. OBD I only needed abnormality 2. OBD II for emissions ONLY! OBD I is not. Most OEMs recommend fixing OBD I first - before checking / repairing OBD II

  36. Diagnostic Trouble CodesOBD I vs. OBD II • OBD I diagnostic procedure was to… • Pull Codes • Record Codes • Erase Codes • Operate Vehicle • Pull Codes • Erasing OBD II Codes will also erase Freeze Frame Data

  37. Diagnostic Trouble CodesOBD I vs. OBD II • OBD II has no “soft codes” • OBD II diagnostic procedure • Pull Code • Record Freeze Frame Data • Repair Root Cause • Operate vehicle at Freeze Frame parameters • Meet code enable criteria • Run monitor

  38. MULTIPLEXING • Vehicles use multiple onboard computers • Faults in other computers can disable monitors due to multiplexing • Example • Wheel Speed Sensors used to verify rough road to prevent false misfire codes

  39. Code Enable Criteria • Definition • “Once the conditions are met to test for the DTC are met, then the monitor will run the test” • P0134 - HO2S - 11 Remains At Center (B1 S1) Code Conditions: • Engine runtime over 2 minutes, ECT sensor input more than 176 degrees F, then the test started and the PCM detected that the front HO2S-11 signal was 0.5v (fixed at mid-range for 1 minute)

  40. ONE TRIP DTCs • MIL will illuminate after one DTC enable criteria has been met and failed! • Most common One Trip failures are… • Misfire & Fuel Control Monitors • CCM will depending on manufacturer • TPS, MAP, MAF, ECT, CKP, etc.

  41. TWO/THREE TRIP DTCs • MIL will illuminate when DTC enable criteria are met and failed in 2 consecutive trips • Compromise for CSI • DTC confirmation

  42. TWO/THREE TRIP DTCs • When 1st trip fails • Code is “pending” or “maturing” • Freeze Frame data is captured, but not displayed • MIL is off

  43. TWO/THREE TRIP DTCs • If & When 2nd trip fails… • MIL is illuminated • Code “matures” & DTC is set • Freeze Frame Data can be viewed • Same with 3 trip failures… • Except add 1 trip

  44. PENDING DTCs • If 2nd trip passes (doesn’t fail)… • Pending Code stays pending for 40 good trips or 80 good trips for misfire / air fuel • Freeze Frame Data is displayed • MIL stays off

  45. MIL Command: MIL “bad trip” counter: MIL “good trips”: DTC Command: DTC “bad trips”: DTC “good trips” Pending DTC: Pending “good trips”: Freeze Frame Data: Off One “bad trip” N/A Off One “bad trip” N/A Set N/A Set, but not displayed MIL Strategies & DTCsFirst Trip Failure

  46. MIL Strategy Exercise

  47. MIL Command: MIL “bad trip” counter: MIL “good trips”: DTC Command: DTC “bad trips”: DTC “good trips”: Pending DTC: Pending “good trips”: Freeze Frame Data: On Reset to zero N/A Set & Displayed Reset to zero N/A Set or cleared N/A Displayed MIL Strategies & DTCs2nd Consecutive Trip Failure

  48. MIL Command: MIL “bad trip” counter: MIL “good trips”: DTC Command: DTC “bad trips”: DTC “good trips”: Pending DTC: Pending “good trips”: Freeze Frame Data: Off Reset to zero N/A Off Reset to zero N/A Set or cleared One “good trip” Displayed or not MIL Strategies & DTCs2nd Consecutive Trip Pass

  49. MIL Command: MIL “bad trip” counter: MIL “good trips”: DTC Command: DTC “bad trips”: DTC “good trips”: Pending DTC: Pending “good trips”: Freeze Frame Data: On Reset to zero N/A Set & displayed Reset to zero N/A Set or cleared N/A Displayed MIL Strategies & DTCsFault Repaired / DTC Not Cleared

  50. DTC Priority Designation • Type “A” DTCs • Usually “One Trip” codes • CAT Damaging or 1.5 X FTP • Type “B” DTCs • Usually “2 or 3 Trip” codes • Serious failure • Type “C” & “D” DTCs • Not emission related / won’t illuminate MIL

More Related