1 / 18

DC ELECTRICAL CIRCUITS

DC ELECTRICAL CIRCUITS. VOLTAGE DIVIDERS. DC ELECTRICAL CIRCUITS. A voltage divider may appear to be a series circuit but its actually a series parallel circuit when a load is applied. It = 30/2000 = .05. THERE ARE NO LOADS PLACED ON R1 OR R2 IN THIS CIRCUIT. DC ELECTRICAL CIRCUITS.

yazid
Télécharger la présentation

DC ELECTRICAL CIRCUITS

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. DC ELECTRICAL CIRCUITS VOLTAGE DIVIDERS

  2. DC ELECTRICAL CIRCUITS • A voltage divider may appear to be a series circuit but its actually a series parallel circuit when a load is applied. It = 30/2000 = .05 THERE ARE NO LOADS PLACED ON R1 OR R2 IN THIS CIRCUIT.

  3. DC ELECTRICAL CIRCUITS • If a 1000Ω load is applied to the R1 resistor it changes the output voltage from 15V to 10V which may not be enough to drive the RL load.

  4. DC ELECTRICAL CIRCUITS • In order to design a workable voltage divider the current that flows through the load must be taken into account. • If we use the example of 3 loads that must be driven by a 12V power supply; First load requires………12V @ 1A, Second load requires….. 8V @ .6A Third load requires………4V @ .2A The circuit will look like…………..

  5. DC ELECTRICAL CIRCUITS • Three resistors are used to develop the three desired voltages, the values are not given, however using ohms law we can determine the values of the resistors that we need.

  6. DC ELECTRICAL CIRCUITS • At R1 there is a bleeder current, (10% of the circuit current), 2A x 10% = .2A, the bleeder current does not flow through any of the loads and R1 is called the bleeder resistor.

  7. DC ELECTRICAL CIRCUITS • We have two values at R1, R2 & R3, lets plug them into ohms law; R1= E/R or 4V/.2A = 20Ω,

  8. DC ELECTRICAL CIRCUITS • Thecurrent through R2 is the sum of the bleeder current of .2A and the load 3 current .2A, so .4A flows through R2. Voltage at the bottom of R2 is 4V and the voltage above R2 is 8V, so 4V/.4A = 10Ω.

  9. DC ELECTRICAL CIRCUITS • The current through R3 is the .4A plus the .6A load current = 1A. The voltage at the bottom of R3 is 8V and the voltage at the top of R3 is 12V, so 4V/1A =4Ω.

  10. DC ELECTRICAL CIRCUITS DESIGNING A VOLTAGE DIVIDER; • Arbitrarily selecting a bleeder current that is 10% of the total current. • Using the bleeder current and the lowest voltage required by the load compute the value of the bleeder resistor. • Using the total current through each resistor and the voltage dropped by the resistor, determine the resistance values required.

  11. DC ELECTRICAL CIRCUITS Series Voltage Divider • VT is divided into IR voltage drops that are proportional to the resistance values. • VR = (R/RT) ´ VT • The largest series R has the largest IR voltage drop.

  12. x VT x 12 V = 4 V V3 = = x VT x 12 V = 2 V V2 = = x VT x 12 V = 6 V V1 = = 1 kW 2 kW 3 kW R2 R1 R3 6 kW 6 kW 6 kW RT RT RT Note: the largest drop is across the largest resistor. DC ELECTRICAL CIRCUITS Series Voltage Divider R3 2 kW R2 1 kW 12 V 3 kW R1 KVL check: 6 V + 2 V + 4 V = 12 V

  13. 10 kW 30 kW DC ELECTRICAL CIRCUITS Redesigned Voltage Divider 10 kW 4.62 kW 40 V 15 kW 10 kW 60 V 10 V 5 kW Two of the divider resistors are smaller and the desired voltages are restored.

  14. VC VB VA DC ELECTRICAL CIRCUITS Grounded Voltage Divider C 10 kW B 15 kW 60 V A 5 kW GROUND IS THE REFERENCE POINT

  15. 20 kW x 60 V = 40 V VB = 30 kW 5 kW x 60 V = 10 V VA = 30 kW DC ELECTRICAL CIRCUITS Grounded Voltage Divider C VC = 60 V 10 kW B 15 kW 60 V A 5 kW GROUND IS THE REFERENCE POINT Note: VB IS THE SUM OF TWO DROPS AND VC IS THE TOTAL VOLTAGE.

  16. This voltage drops to 38.8 V This voltage drops to 7.06 V 10 kW DC ELECTRICAL CIRCUITS Loading a Voltage Divider 10 kW 40 V 15 kW 60 V 10 V 5 kW

  17. DC ELECTRICAL CIRCUITS • Another widely used series parallel circuit is the bridge circuit, bridge circuits are either balanced or unbalanced.

  18. DC ELECTRICAL CIRCUITS • An unbalanced bridge circuit will not be zero volts or zero amps. • Some bridge circuits are; • Wheatstone bridge- used to measure resistance. • Self balancing bridge- used to control motion at a distance (roof top antenna). • Temperature Sensing Bridge- used for measuring temperature.

More Related