1 / 26

Spanning Tree Algorithm

Spanning Tree Algorithm. Network Protocols and Standards Autumn 2004-2005. Topologies with Loops. Problems Frames proliferate Learning process unstable Multicast traffic loops forever. A. LAN 1. B1. B2. B3. LAN 2. Topologies with Loops. Solutions

zena
Télécharger la présentation

Spanning Tree Algorithm

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Spanning Tree Algorithm Network Protocols and Standards Autumn 2004-2005 CS573: Network Protocols and Standards

  2. Topologies with Loops • Problems • Frames proliferate • Learning process unstable • Multicast traffic loops forever A LAN 1 B1 B2 B3 LAN 2 CS573: Network Protocols and Standards

  3. Topologies with Loops • Solutions • Require that the topologies be loop-free through careful deployment of segments and bridges • Design Bridges to detect loops and complain and, perhaps, stop working • Not a good idea because loops provide redundancy • Design into the bridges an algorithm that prunes the topology into a loop-free subset (a spanning tree) • Blocking of some ports may be required • Automatically adapt to the changes in topology CS573: Network Protocols and Standards

  4. Reconfiguration Algorithm • Configures an arbitrary topology into a spanning tree • Automatic reconfiguration in case of topology changes • The algorithm should converge for any size LAN; the stability should be achieved within a short, bounded time • Active topology should be reproducible and manageable • Transparency to end-stations is required • Must not use a lot of bandwidth CS573: Network Protocols and Standards

  5. Spanning Tree Algorithm • A distributed Algorithm • Elects a single bridge to be the root bridge • Calculates the distance of the shortest path from each bridge to the root bridge (cost) • For each LAN segment , elects a “designated” bridge from among the bridges residing on that segment • The designated bridge for a LAN segment is the one closest to the root bridge • And… CS573: Network Protocols and Standards

  6. Spanning Tree Algorithm • For each bridge • Selects ports to be included in spanning tree • The ports selected are: • The root port --- the port that gives the best path from this bridge to the root • The designated ports --- ports connected to a segment on which this bridge is designated • Ports included in the spanning tree are placed in the forwarding state • All other ports are placed in the blocked state CS573: Network Protocols and Standards

  7. Forwarding frames along the spanning treeForward and Blocked States of Ports • Data traffic (from various stations) is forwarded to and from the ports selected in the spanning tree • Incoming data traffic is always discarded (this is different from filtering frames. Why?) and is never forwarded on the blocked ports CS573: Network Protocols and Standards

  8. Root Selection: Bridge ID • Each port on the Bridge has a unique LAN address just like any other LAN interface card. Bridge ID is a single bridge-wide identifier that could be: • A unique 48-bit address • Perhaps the LAN address of one of its ports • Root Bridge is the one with lowest Bridge ID B Port Address CS573: Network Protocols and Standards

  9. Path Length (Cost) • Path length is the number of hops from a bridge to the root • While forming a spanning tree, we are interested in the least cost path to the root • Cost can also be specified based on the speed of the link • Not fair to treat a 10Mb/s link the same as a 1Gb/s link • A guideline for cost selection is in Table 8.5 of the latest IEEE 802.1D standard CS573: Network Protocols and Standards

  10. Path cost guidelines Source: IEEE 802.1D standard CS573: Network Protocols and Standards

  11. Example Topology 1 4 5 7 8 6 10 11 2 0 CS573: Network Protocols and Standards

  12. After algorithm execution DP 1 RP DP BP BP 4 5 7 RP RP RP RP DP DP 8 6 10 DP RP RP BP DP 11 2 RP RP RP: Root Port DP: Designated Port BP: Blocked Port DP 0 DP CS573: Network Protocols and Standards

  13. Configuration Message (BPDU) • Configuration Bridge Protocol Data Unit • Transmitted by Bridges to implement the spanning tree algorithm • Just like any other data link layer frame • Destination Adderss: Special Multicast Address • 01-8-c2-00-00-00 • Source Address: MAC address of the port • DSAP = SSAP = 01000010 Data Field 6 octets 2 octets 2 octets 6 octets destination source length DSAP SSAP Configuration Message CS573: Network Protocols and Standards

  14. Configuration BPDU Contents • The Data Field of Config BPDU contains: • Root ID • ID of the Bridge known to be root • Cost to Root • Cost of the known least cost path to the root • Transmitting Bridge ID • ID of the bridge transmitting this message • Representation • <RootID>.<CostToRoot>.<TransmittingBridgeID> CS573: Network Protocols and Standards

  15. BPDU: Transmission and Processing • When a bridge is first booted up: • It assumes it is the root • Transmits on each port: • <ownID>.<0>.<ownID> • BPDUs are received on each port • For each port, every bridge saves the best BPDU received • Best among the ones received or transmitted on that port CS573: Network Protocols and Standards

  16. Comparing two BPDUs • Given two BPDUs containing configuration messages C1 and C2: • C1 is better than C2 if rootID in C1 is lower than the rootID in C2 • In case of a tie above, C1 is better than C2 if cost in C1 is lower than the cost in C2 • In case of a tie above, C1 is better than C2 if transmitting bridge ID in C1 is lower than the transmitting bridge ID in C2 • Can we still get a tie? • Consider a bridge with two ports on same segment!!! CS573: Network Protocols and Standards

  17. Port Identifier Each bridge has an internal numbering of its ports These numbers are unique only for a bridge Bridge 1 0 2 3 CS573: Network Protocols and Standards

  18. Port Identifier • Port IDs are useful when rootID, cost, and transmittingBridgeID are the same in two configuration messages • In such situations, Port IDs are used as tie-breakers and the BPDU with lower portID is better CS573: Network Protocols and Standards

  19. Message C1 <Root>.<Cost>.<Tx> <29>.<15>.<35> <35>.<80>.<39> <35>.<15>.<80> Message C2 <Root>.<Cost>.<Tx> <31>.<12>.<32> <35>.<80>.<40> <35>.<18>.<38> Comparing BPDUs (a) (b) (c) In all cases above, C1 is “better” than C2 CS573: Network Protocols and Standards

  20. Designated Bridge • If a bridge receives better BPDU on a port than the one it would transmit, it will no longer transmit BPDUs on that port • As a result, only one bridge called the “designated bridge” transmits configuration BPDUs on each LAN CS573: Network Protocols and Standards

  21. Root ID and Cost: determining • Consider B with bridge ID 18 • Best BPDUs on each of its ports are: <RootID>.<Cost>.<TransmitterID> • Port 1 <12>.<93>.<51> • Port 2 <12>.<85>.<47> • Port 3 <81>.<0>.<81> • Port 4 <15>.<31>.<27> • Root bridge ID is determined as 12 • Least cost is determined as 85+1 = 86 • Port 2 is regarded as the Root port …cont… CS573: Network Protocols and Standards

  22. Root ID and Cost: determining • At next opportunity, B will transmit • <12>.<86>.<18> • Better than the best BPDUs on all ports • Ports 1, 3, and 4 are designated • B considers itself designated for the segments connected to ports 1, 3, and 4 • B continues transmitting BPDUs on those segments (through respective ports) CS573: Network Protocols and Standards

  23. Spanning Tree Ports • For each bridge, what ports are “included” in the spanning tree? • Root Port • On which best of the best BPDUs is received • Designated Port • Connected to segments on which B is designated • Ports selected in the spanning tree are placed in the forwarding state • B will forward data packets to and from those ports CS573: Network Protocols and Standards

  24. Ports Blocked • Bridge B will block a port if it receives a better BPDU on that port than the one it would transmit (except for the root port) • Bridge B will no longer transmit BPDUs on either root port or blocked ports • Data packets are not forwarded to and received from the blocked ports CS573: Network Protocols and Standards

  25. Port 1 Bridge ID 92 Port 5 Port 4 Port 2 Port 3 41.13.90 81.0.81 41.12.111 41.12.315 41.19.125 Example Root Bridge is selected as 41 Least cost to root is 12+1 = 13  Port 4 is selected as root Now B92 will transmit a BPDU 41.13.92 What does it do with the ports? CS573: Network Protocols and Standards

  26. How the Ports are treated? Remember: B92 will transmit a BPDU 41.13.92 • Port 1: 41.13.92 < 81.0.81  DP • Port 2: 41.13.92 < 41.19.125  DP • Port 3: 41.13.92 > 41.12.315  BP • Port 4: 41.13.92  Root Port • Port 5: 41.13.92 > 41.13.90  BP CS573: Network Protocols and Standards

More Related