1 / 29

Intel 8086

Intel 8086. Registers. (16-bit) registers: Data reg. – to hold data for an op. Address reg – to hold addr of an instruction or data Status reg / FLAGS reg. 1. Data reg - 4. AX BX CX DX High byte – H Low byte – L AX  AH + AL. AX – Accumulator reg.

deepak
Télécharger la présentation

Intel 8086

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Intel 8086

  2. Registers • (16-bit) registers: • Data reg. – to hold data for an op. • Address reg – to hold addr of an instruction or data • Status reg / FLAGS reg

  3. 1. Data reg - 4 • AX • BX • CX • DX High byte – H Low byte – L AX  AH + AL

  4. AX – Accumulator reg • Preferred reg to use in arith/logic/data transfer instructions • Multiplication or Division ops.  one of the nos. must be in AX or AL • I/O operations also require the use of AX/AL

  5. BX – Base reg • It also serves as an Address reg.

  6. CX - Count reg • Loop counter • REP – repeat [in string operations] • CL  as a count in instructions that shift and rotate bits

  7. DX – data reg • Used in MUX and Division • Used in I/O ops.

  8. Registers • (16-bit) registers: • Data reg. – to hold data for an op. • Address reg – to hold addr of an instruction or data • Status reg / FLAGS reg

  9. 2. Address reg. a. Segment reg  CS, DS, SS, ES b. Pointer & index reg  Si, DI, SP, BP, IP

  10. a. Segment regs. – 4 • Each memory byte has an address • 8086 proc assigns a 20-bit physical address to its memory locations • It is possible to address  220 = 1,048,576 = 1 MB of memory • 1st byte’s address: 0000 00000000 00000000 • 2nd byte’s address: 0000 00000000 00000001 • 3rd0000 00000000 00000010 …

  11. In HEX • 00000 • 00001 • 00002 . . . • FFFFFh

  12. 16-bit processor! 20-bit address!! Q. Where lies the problem?? • 20-bit addresses are bigger to fit in a 16-bit reg or memory word.

  13. টুকরা টুকরা Memory Segment • Partioning memory into segments • A memory segment is a block of 216 or 64K consecutive memory bytes • Segment number – for each segment • Q: How many bits for a segment number?  16 bits! – as each block has byte of 216

  14. Segment: Offset address • Within a segment, a memory location is specified by giving an offset. Memory location  Segment no. + Offset Segment:Offset  Logical Address

  15. A4FB:4827h •  offset 4827, within segment A4FB Q: How to get 20-bit physical address? • Shift the segment address 4 bits to the left (eqv. to multiplying by 10h) • Add the offset So, the Physical Address for A4FB:4827h ???

  16. Logical Address: A4FB:4827h A 4 F B 0 + 4 8 2 7 A 9 8 2 2h  Physical Address 20-bit Physical Address  16-bit Segment [after shifting] + 16-bit Offset

  17. CS, DS, SS, ES Machine lang.  - instruction [code] - data - stack [data structure – used by the proc to implement procedure/function calls] These are loaded into different memory segments, • Code segment - CS • Data segment - DS • Stack segment - SS

  18. ES – extra segment reg • If a prog needs to access a second data segment, use the ES register! • At any time – only 4 mem locations addressed by the 4 segment reg [C/D/S/E] are accessible Q: How many memory segments can remain active at a time?  only 4 memory segments are active

  19. Registers • (16-bit) registers: • Data reg. – to hold data for an op. • Address reg – to hold addr of an instruction or data • Status reg / FLAGS reg

  20. 2. Address reg. a. Segment reg  CS, DS, SS, ES b. Pointer & index reg  SI, DI, SP, BP, IP

  21. b. Pointer & Index reg. • Stack pointer – SP – with SS [??] to access the stack segment • Base pointer – BP – mainly to access data on the stack. Also to access data in other segments. • Source index – SI – to point to memory locations in the data segment addressed by DS [??] • Destination index – DI  same as SI – but for instructions of string operations – to access memory locations – addressed by ES [??]

  22. Instruction pointer [IP] reg. Q: Which registers so far are for data access or to access instructions? • All above are for data access! • CS [Code segment – under Segment reg.] contains segment no. of the next instruction. • IP contains the offset

  23. IP is updated each time an instruction is executed – so that it will point to the next instruction. Q: Can IP reg be directly manipulated by an instruction?  Unlike other registers - NO!

  24. Registers • (16-bit) registers: • Data reg. – to hold data for an op. • Address reg – to hold addr of an instruction or data • Status reg / FLAGS reg

  25. 3. Status Reg./FLAGS reg. • To indicate the status of the mP. • 1 flag == 1 bit • Y/N • 9 active bits – out of ?? Bits? Q: Types of flags? Some names? • Status flags – Zero flag, Carry flag, sign flag, parity, auxiliary flag and overflow flag • Control flags – interrupt flag, trap flag, direction flag

  26. 8086 Internal Configuration

  27. Simplified block diagram over Intel 8088 (a variant of 8086); 1=main registers; 2=segment registers and IP; 3=address adder; 4=internal address bus; 5=instruction queue; 6=control unit (very simplified!); 7=bus interface; 8=internal data bus; 9=ALU; 10/11/12=external address/data/control bus

More Related