1 / 32

Installation

Installation. Luff Conveyor Components. Structure Alignment Parallel Straight Square Level. Parallel. Straight. Frame Alignment. Level. Pulleys. Pulley Alignment + or - 1/32” level & perpendicular to the belt Misalignment Excessive thrust load on bearings

abel
Télécharger la présentation

Installation

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Installation LuffConveyor Components

  2. Structure Alignment • Parallel • Straight • Square • Level

  3. Parallel

  4. Straight

  5. Frame Alignment

  6. Level

  7. Pulleys

  8. Pulley Alignment • + or - 1/32” level & perpendicular to the belt • Misalignment • Excessive thrust load on bearings • Accelerated & uneven lagging wear • Belt training problems

  9. Installation • Idler alignment • Square and in-line to the conveyor centerline and referenced from a terminal pulley • Parallel to each other

  10. Idler Alignment

  11. Installation • Belt alignment • Initially - train the belt empty • Then - train the belt under full design load • Helpful hints • Only one person supervise the training

  12. Installation • Belt alignment • Helpful hints (continued) • After run-in period, check readings for voltage, amps, or watts for comparison • Higher future readings may indicate excessive drag from de-training or frozen idler rolls

  13. Installation • Belt alignment • Helpful hints (continued) • Do not over-train. This will increase belt wear and power consumption

  14. Effect on Idler Life

  15. Effect on Idler Life

  16. Effect on Idler Life

  17. Maintenance • Inspection Plan (continued) • Thoroughly clean grease fittings to eliminate the possibility of introducing contamination into bearings

  18. Maintenance • Skirtboard adjustment • Skirtboards centralize & shape the load to minimize spillage • Steel backing plates should be high enough to avoid risk of contact with the belt • Typical gap is 1/2” at the tail opening and increases to 1” at the exit of the load zone

  19. Maintenance • Belt splicing • The splice “MUST” be square • The only corrective action for a non-squared splice, is to re-splice

  20. Training Problem Conveyors

  21. Maintenance • Training • Training or self-aligning idlers DO NOT train a belt • Only the center roll of a troughing idler effects training. Wing rolls only offer load support

  22. Maintenance • Training (continued) • Tilting troughing idlers forward, not over 2 degrees, in the direction of belt travel, produces a self-aligning effect (caution on reversing belts)

  23. Maintenance • Training (continued) • Procedure • Square and level all troughing idlers, return rolls, tail, head, take-up, snub, and drive pulleys • Check counterweights and the sag on the return belt (2” per 10’)

  24. Maintenance • Training (continued) • Check all center rolls on troughing idlers & check return rolls for proper belt contact • Check troughing frames for tilt degree and make corrections

  25. Maintenance • Training (continued) • Start training adjustments at the head end and on the return side. Check and adjust all return rolls to the tail pulley (this assures early centering at the loading point on the belt)

  26. Maintenance • Training (continued) • After the return side is running true, start training the top troughing idlers from the tail to the head pulley (end of procedure)

  27. Maintenance • Training (continued) • Train the belt empty first, then train the belt under full design load • If the belt trains well empty, then later problems will be due usually to off-center loading or material build-up on rolls

  28. Maintenance • Training (continued) • Idlers can be “knocked” to train belt • In the direction of belt travel, knock forward the idler end to which the belt runs (***visualize bicycle handle bars***)

  29. Maintenance • Training (continued) • Shift idlers in the area preceding the detraining area of the conveyor • 1/4” max adjustment • Caution - knocking may have adverse effects on reversing belts

  30. Maintenance • Training (continued) • Training idlers should not be located within 25-50 feet of a head or tail pulley, vertical curves, or abrupt changes in direction • The belt tends to run to the down side of an unlevel pulley

  31. Maintenance • Training (continued) • V-trough return rolls train very well • The side guide rolls on training idlers should be mounted inbound of the belt direction

More Related