1 / 15

ME317 Tolerance Stack-ups

ME317 Tolerance Stack-ups. Problems due to tolerance stack-ups include:. Failure to assemble Interference between parts Failure of parts to engage Failure to function as intended. Overview:. Tolerance stack-ups are accumulations of variations on drawings or in part assemblies.

april-hayden
Télécharger la présentation

ME317 Tolerance Stack-ups

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. ME317Tolerance Stack-ups

  2. Problems due to tolerance stack-ups include: • Failure to assemble • Interference between parts • Failure of parts to engage • Failure to function as intended

  3. Overview: Tolerance stack-ups are accumulations of variations on drawings or in part assemblies.

  4. Example: Accumulation of tolerances on a drawing. 3.00±0.01 7.00±0.01 What is the effective dimension and tolerance between the two holes?

  5. In this case the tolerances add directly The furthest apart the two centers can be is 7.01-2.99=4.02 The closest is 6.99-3.01=3.98 Thus, the effective dimension and tolerance is 4.00±0.02 This addition of tolerances may make it hard to join with a mating part that has two pins that fit in those holes.

  6. What can we do as designers to improve this?

  7. The logical thing is to put the dimension and tolerance directly on the hole spacing if that is the location most important to function. 7.00±0.01

  8. A±a Gap B±b C±c Example: Assembly of individual parts Suppose we have two blocks, A and B that are to fit into a slot in C, all with tolerances shown.

  9. Let’s look at the largest and smallest gap that we could have. Largest Gap = (C+c) – (A-a) – (B-b) = C – (A+B) + (a+b+c) Smallest Gap = (C-c) – (A+a) – (B+b) = C – (A+B) – (a+b+c) Consequently the dimension and tolerance of the gap is effectively: {C-(A+B)} ± (a+b+c)

  10. If we have 10 parts (say a clutch pack) that all have to fit into a housing, the addition of all those tolerances can be significant. If controlling the spacing of the clutches is important to function we have a problem. What can we do as designers?

  11. Solutions • Tighten up the tolerances on each component so the sum of the tolerances is lower. • Include a spacer that comes in different sizes to take up any slack resulting from the tolerance addition (similar to shimming). • Design so that the tolerance stacks are not relevant to function. • Consider that the variation in each part is likely to be statistically distributed.

  12. Example: 2-D Consider a swing weight governor similar to the one shown below

  13. L1±l1 H L2±l2 Simplifying further, assume: • Holes are perfectly located • Pins and holes have zero clearance and move freely • Only length of links has tolerance

  14. The height can be found using geometry (specifically, the Law of Cosines). H2 = L12 + L22 - 2l1l2cosα (where α is the angle between the legs) And Hmax2 = (L1+l1)2 + (L2+l2)2 – 2(L1+l1)(L2+l2)cosα Hmin2 = (L1-l1)2 + (L2-l2)2 – 2(L1-l1)(L2-l2)cosα

More Related