1 / 33

ECE 496 TEAM POETA FINAL PRESENTATION

ECE 496 TEAM POETA FINAL PRESENTATION. Anna Hart Brad Heath Matthew Poeta. Michael Rock Debbie Schneider Jae Sin. OUTLINE. INTRODUCTION/RULES HARDWARE DESIGN CONTROLS DESIGN PROBLEMS, SUGGESTIONS RESULTS BONUS DAY COMPETION DAY THANKS CONCLUSION. INTRODUCTION.

arleen
Télécharger la présentation

ECE 496 TEAM POETA FINAL PRESENTATION

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. ECE 496TEAM POETAFINAL PRESENTATION Anna Hart Brad Heath Matthew Poeta Michael Rock Debbie Schneider Jae Sin

  2. OUTLINE • INTRODUCTION/RULES • HARDWARE DESIGN • CONTROLS DESIGN • PROBLEMS, SUGGESTIONS • RESULTS • BONUS DAY • COMPETION DAY • THANKS • CONCLUSION

  3. INTRODUCTION • WEAPONS OF MASS DESTRUCTION (IN THE HANDS OF EVIL) • CRUISE SHIPS OF THE FUTURE (IN THE HANDS OF GOOD)

  4. RULES • INVERTED PENDULUM BEHAVIOR • TWO LINKS, EACH 18-INCHES LONG • ONLY ONE MOTOR MAY BE USED • ONLY ENCODERS MAY BE CONNECTED TO THE ARMS • FIGURE 1 SHOWS PENDUBOT SCHEMATIC

  5. SCHEMATIC

  6. BLOCK DIAGRAM

  7. CONTROLS DESIGN • SWING-UP • SWITCH CONTROL • BALANCE • ALTERNATIVE METHODS

  8. CONTROLS DESIGN

  9. SWING-UP CONTROL • CONSTANT VOLTAGE OUTPUT TO MOTOR • VOLTAGE CUT OFF FROM MOTOR AT EXPERIMENTAL ANGLE • MOMENTUM OF ARM CARRIES LINKS TO DESIRED TRANSITION ANGLE

  10. SWING-UP CONTROL

  11. SWITCH CONTROL • ONCE THE LINKS WERE IN DESIRED POSITIONS BALANCE CONTROL TURNED ON • MOTOR LINK WITHIN ±35 DEGREES OF VERTICAL • ENCODER LINK WITHIN ±6 DEGREES OF MOTOR LINK ANGLE

  12. SWITCH CONTROL

  13. BALANCE CONTROL • FOUR PARAMETERS: • POSITION OF MOTOR ENCODER • VELOCITY OF MOTOR ENCODER • POSITION OF LINK ENCODER • VELOCITY OF LINK ENCODER • (ERRORS x GAIN)  VOUT TO MOTOR

  14. BALANCE CONTROL

  15. ALTERNATIVE METHODS • SWING UP FROM ECE 496 CD • SINUSOIDAL SWING-UP

  16. HARDWARE DESIGN • ENCODERS • 1000 PULSES PER REVOLUTION, DUAL QUADUATURE CHANNEL • SUPPLY VOLTAGE: 5-24 VDC • CURRENT: 175 mA

  17. HARDWARE DESIGN • MOTOR • 90 VDC PERMANENT MAGNET, ½ HP, 1725 RPM

  18. HARDWARE DESIGN • PENDUBOT ARM

  19. PROBLEMS • ARM DESIGN IS NOT IDEAL • DESIGNED SO THAT THERE WAS NO WEIGHT AT THE TOP. DURING BALANCING, FOUND THAT NOT HAVING WEIGHT RESULTED IN NO INERTIA. • ATTACHMENT OF LINK ENCODER • ARMS WERE DANGEROUS! • SHARP EDGES

  20. PROBLEMS (cont.) • ENCODERS ARE TOO BIG AND HEAVY • SPRING IN LINK ENCODER BROKE • NEEDED ENCODER CABLE CONNECTORS • CABLES KEPT COMING LOOSE • SOME WIRES FAILED TO WORK • WIRES FROM RCA CONNECTOR SOLDERED TO ENCODER CABLE FREQUENTLY CAME LOOSE

  21. PROBLEMS (cont.) • TIME SPENT IN ACQUIRING MOTOR • LAWRENCE (“BUBBA”, scary man) • FRICKS • COLUMBIA - HONEYWELL MOTOR • BREAKOUT BOARD FILES WERE INCORRECT • LINEAR AMP OVERHEATED AND DIED • ORIGINAL SWING-UP CONTROL METHOD DID NOT WORK

  22. SUGGESTIONS • DON’T WASTE TIME • BUILD ARM BEFORE ORDERING PARTS • HAVE MORE INFORMATION ABOUT PARTS BEFORE ORDERING • START CALLING VENDORS EARLY • KNOW WHAT YOU ARE LOOKING FOR BEFORE YOU GO TO A JUNK YARD

  23. MORE SUGGESTIONS • DOUBLE STICK TAPE: NOT GOOD FOR EVERTHING • NEVERSTART CONTROL PROGRAM WITH GAIN ALL THE WAY UP. • NEVERATTEMPT TO CATCH THE PENDUBOT WITH BARE HANDS • NEVERWORK ON PENDUBOT ALONE

  24. YET MORE SUGGESTIONS • MAKE SURE THE BATHROOM WINDOWS ARE OPEN • HAVE LOTS OF PADDING • USE SOLID WIRE • BUY A LOT OF ELECTRICAL TAPE • NEED A LOT OF SLACK IN CABLES

  25. BONUS DAY RESULTS

  26. COMPETITION DAY RESULTS • GROUP B WINS • TOP TIME: 1.12 SECONDS • GROUP E DOES NOT WIN • SWING-UP CONTROL GOOD • BALANCING CONTROL UNSTABLE • SATURDAY, DECEMBER 2 • AT LAST, TEAM POETA ENJOYS SUCCESS!

  27. SPECIAL THANKS AND ACKNOWLEDGEMENTS • From ECE 496: • For Design advice, troubleshooting help and moral support.. • Group A - Darla King, Scott Schauberger, Ruben Suzara • Group B - Andy Halavonich • Group C - Robert Helms, Bryan Ripple • Group D - Michael Bryant, Spencer Farland, Carey Salisbury(Group D - mostly for moral support..Thanks guys!!)

  28. SPECIAL THANKS AND ACKNOWLEDGEMENTS • Not from ECE 496: • Uncle Jesse at Lawrences Salvage Yard - for clearing up our misconception that a DC motor can turn both ways! • Jeremy Rudbeck - for technical and moral support • Adam Baier, Alex Funk, Todd Dunn, Tim Cobb - because they meant well • Gary Poeta - for assistance in re-forming the pendubot arm and mounting the link encoder after our "accident"

  29. SPECIAL THANKS AND ACKNOWLEDGEMENTS • Not from ECE 496: • Jason Anderson(Dr. Dawson's Grad Student) - for simulink adviceand help mounting the link encoder • Dennis Moses(Dr. Dawson's Grad Student) - for ALL his help • Johnny Allison(Advanced Automation) - for technical advice and working as liason between Group E and Advanced Automation

  30. SPECIAL THANKS AND ACKNOWLEDGEMENTS • Not from ECE 496: • Mark Townsend(and machine shop at Advanced Automation)- for machining the pendubot arms • Jim Hunter at BEI - for donating the encoders for the links • Jim at Grainger - for donating the DC motor

  31. THANKS • PC BREAKOUT BOARD COMPONENTS DONATED BY A GRANT FROM THE CLEMSON UNIVERSITY ECE DEPARTMENT

  32. CONCLUSION • WE WOULD LIKE TO CONCLUDE THAT ….

  33. QUESTIONS??

More Related