Water and Solutions

1. Water and Solutions

2. The importance of water • Important component of solutions • Water quality, composition, and pH can drastically affect an experiment

3. Which water should I use? • Tap water • Variable chemistry and purity • Laboratory grade water • Reverse osmosis or distillation • Rinsing glassware, media preparation • Reagent grade water • Filtration, deionization, and carbon adsorption • Most laboratory uses • Other specialized types (dd, microfiltered, electrically deionized, etc.)

4. Solution terminology • Solution: A mixture in which individual molecules or ions are dispersed in a liquid. • Solvent: The liquid that makes up the majority of the solution. • e.g., water (aqueous solution) • Solute: The minority component of the solution. Often a solid before mixing.

5. Measurements of concentration • In almost all cases, these are amount of solute per volume of SOLUTION.* • Weight-per-volume (e.g., mg/L) • Percent (parts per hundred) • PPT, PPM, PPB • Molar solutions * [The exception is molal solutions (moles of solute per liter of solvent) but we will not discuss them further in this class.]

6. Weight-per-volume concentration • g/L, µg/mL, etc. • How to make up a 10 g/L aqueous solution: • Weigh out 10 g of the substance. • Put it in a vol. flask or grad. cylinder • Add water up to the 1 L mark. • If you mix 1 L water with 10 g solute, then the total volume would be >1 L, and the concentration would be <10 g/L.

7. Percent (parts per hundred) • w/w = grams per hundred grams total • (this applies to compounds in solid materials, too) • v/v = mL per hundred mL solution • w/v = g per hundred mL solution • Example: to make 100 mL of 10% v/v methanol solution, use 10 mL methanol and add water to a total volume of 100 mL.

8. PPT, PPM, PPB • Like percent, except more dilute • parts per thousand • parts per million • parts per billion • 1 ppm = 1 µg/g = 1 µg/mL = 1 mg/L (1 g of water = 1 mL)

9. Molar (M) Solutions • Definition: moles of solute per liter of solution • 1 mole is 6x1023 molecules. • The mass of 1 mole of a compound is the molecular weight (MW) of that compound • What you need to know: • Volume desired • Concentration desired • Formula weight (FW) (FW = MW + water of hydration, if any)

10. A 1M solution is the FW of a substance in 1 liter of solution. • Example 1: • Make up 1 liter of 1M NaCl…

12. Example 2: • Make up 400 ml of 0.25M NaCl • Example 3: • Make up 1L of 5mM NaH2PO4

13. Normal (N) solutions • Definition: The molarity of hydrogen ion equivalents produced by a compound in solution. (Usually applies to acids/bases.) • What does this mean? • For many chemicals the molarity and normality are the same • 1M HCl is the same composition as 1N HCl • Same for HNO3, HF, most organic acids (e.g. HCOOH)

14. Differences between molar and normal solutions occur when you are working with molecules with >1 exchangeable proton. • Sulfate, phosphate, carbonate • 18M sulfuric acid (H2SO4) is 36N • There are 2 H+ ions (protons) per molecule • Multiply the molarity of a solution by the number of H+ to get normality • 5M phosphoric acid (H3PO4) is 15N

15. Dilution from one concentration to another C1V1=C2V2 C1 = initial concentration V1 = initial volume C2 = desired final concentration V2 = desired final volume

16. Examples • You need 100 ml of 1M NaCl and you have a stock solution of 5M NaCl • What do you know? • C1 = 5M • C2 = 1M • V2 = 100ml • Answer … solve for V1 = C2V2/C1 • = 1M x 100 ml/5M = 20 ml of the stock

17. Making very dilute solutions • When making very dilute solutions (micromolar concentrations, etc.) you may need to design a 2-step protocol. • You can’t weigh out <10 mg easily. • So use more, make a concentrated stock solution, and then dilute from the stock.

18. One other complication • Sometimes a concentration is specified in terms of one element in the solution: • Make up 1 L of 10 ppm Zn solution • That would be 10 mg Zn per liter. • But elemental Zn is an insoluble metal! • Use zinc sulfate (heptahydrate) – ZnSO4 • You’ll need to use more than 10 mg of zinc sulfate to get the 10 mg of zinc that you want. • Multiply amount of zinc needed by the ratio of formula weight to atomic weight of Zn.

19. Special considerations for strong acids and bases • SAFETY: Whenever possible, add acid to water, not water to acid. • Important primarily for very concentrated acids • Prevents splashing & over-heating of acid • “Full-Strength” is not necessarily 100%. • Ex.: 100% HCl is a gas! The most concentrated liquid form is a 36% aqueous solution. • So when diluting to make 10% HCl, you are starting from 36%, not 100%. • Acid concentration chart

20. Practice problems • 1. Describe how you would make up • 250 ml of 200 mM NaCl. • 250 ml of a 0.05M glucose solution • 10 ml of 10-5 M glucose solution starting from a 0.05 M stock solution • 2. How many grams of acetic acid would you use to make 10L of a 0.1 M solution of acetic acid?

21. 3. What volume of 10 M acetic acid is required to produce 1 liter of 0.5 M acetic acid? • 4. Describe how to make a 2 N solution of sulfuric acid.

22. 5. Describe how to prepare 500 ml of a 0.25M solution of sodium hydroxide from a 1.0M stock solution of sodium hydroxide.

23. More Practice ProblemsFor hints and answers to these problems go to:http://facweb.furman.edu/~apollard/bio22/solution_problems.htm • Outline how you would prepare 250 ml of a 500 mM solution of potassium chloride.  For this problem only, and not for those that follow, give complete details of what glassware you would use, and the mechanics of making the solution. • How would you prepare 100 ml of a 5 µM solution of ammonium nitrate (NH4NO3)? • Pete Paladin measures out 30 ml of 1M sucrose solution, and then adds water to make a total volume of one liter. What is the molarity of the final solution? • Outline how you would prepare 1 liter of 10% lactic acid, from a bottle you would probably find in the laboratory supply cabinet. What extra step should you take as a safety precaution? • Outline how you would prepare one liter of a solution of 5 ppmnickel.  The chemical available to you is nickel chloride (NiCl2·6H20). • What is the molarity of nickel in the 5 ppm solution prepared above?