1 / 19

Minimum Weight Plastic Design For Steel-Frame Structures

Minimum Weight Plastic Design For Steel-Frame Structures. EN 131 Project By James Mahoney. Program. Objective: Minimization of Material Cost Amount of rolled steel required Non-Contributing Cost Factors Fabrication Construction/Labor costs. Program Constraints.

avedis
Télécharger la présentation

Minimum Weight Plastic Design For Steel-Frame Structures

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Minimum Weight Plastic DesignFor Steel-Frame Structures EN 131 Project By James Mahoney

  2. Program • Objective: Minimization of Material Cost • Amount of rolled steel required • Non-Contributing Cost Factors • Fabrication • Construction/Labor costs

  3. Program Constraints • Structure to be statically sound • Loads transmitted to foundation through member stresses • Members capable of withstanding these internal stresses

  4. Member Properties • Wide-Flange Shape • Full Plastic Moment Mp ≈ Fyx(Flange Area)xd Weight ≈ Proportional to Mp Total Flange Area >> Web Area Weight ≈ Proportional to Flange Area

  5. Objective Function • Calculating Total Weight • Each member assigned full plastic moment • Weight = member length x “weight per linear foot” • Vertical members: Weight = H x Mp • Horizontal members: Weight = L x Mp

  6. Objective Function • For a Single Cell Frame • Min Weight = 2H x Mp1 + L x Mp2 P P Mp2 Mp1

  7. Objective Function • Frame for Analysis

  8. Objective Function • Minimum Weight Function MIN = H x (Mp1+2xMp2+Mp3+Mp4+2xMp5+Mp6+2xMp13) + L x (Mp7+Mp8+Mp9+Mp10+Mp11+Mp12+Mp14) • Subject to constraints of Static Equilibrium

  9. Equilibrium State • Critical Moment Locations in Frame • Seven critical moment “nodes” form that are the result of plastic hinging • One hinge develops at each member end (when fixed) and under the point load • Moments causing outward compression are positive while moments producing outward tension are negative • Critical moments in each member are paired with an assigned full plastic moment

  10. Use of Virtual Work • Principle: EVW = IVW • The work performed by the external loading during displacement is equal to the internal work absorbed by the plastic hinges • Rotational displacement measured by θ said to be very small

  11. Use of Virtual Work • Beam Mechanism (Typical) P θ θ 2θ IVW = EVW L/2 L/2 -M1θ + 2M2θ – M3θ = P(L/2)θ or -M1 + 2M2 – M3 = P(L/2)

  12. Use of Virtual Work • Loading Schemes • Point Loads • Defined placement along beam • R (ratio factor) = 0.5 at midspan, etc. • Results in adjustment of beam mechanism equations for correct placement of hinges • Distributed Load • Placed over length of beam • Result is still a center hinge • Change in EVW formula EVW = Q*(L^2)/4

  13. Use of Virtual Work • Seven Beam Mechanisms • One for each beam -(1-R1)*VALUE(24)+VALUE(23)-R1*VALUE(22) = P1*R1*(1-R1)*L -(1-R2)*VALUE(21)+VALUE(20)-R2*VALUE(19) = P2*R2*(1-R2)*L -(1-R3)*VALUE(18)+VALUE(17)-R3*VALUE(16) = P3*R3*(1-R3)*L -(1-R4)*VALUE(4)+VALUE(5)-R4*VALUE(6) = P4*R4*(1-R4)*L -(1-R5)*VALUE(7)+VALUE(8)-R5*VALUE(9) = P5*R5*(1-R5)*L -(1-R6)*VALUE(10)+VALUE(11)-R6*VALUE(12) = P6*R6*(1-R6)*L -VALUE(33)+2*VALUE(34)-VALUE(35) = Q1*(L^2)/4

  14. Use of Virtual Work • Sway Mechanism (Simple Case) P IVW = EVW H θ -M1θ + M2θ – M3θ + M4θ= PHθ or -M1 + M2 – M3 + M4= PH

  15. Use of Virtual Work • Three Sway Mechanisms • One for each level of framing VALUE(1)-VALUE(25)+VALUE(28)-VALUE(15) = F1*H -VALUE(2)+VALUE(26)-VALUE(29)+VALUE(14)+VALUE(3)-VALUE(27)+VALUE(30)-VALUE(13) = F2*H -VALUE(31)+VALUE(32)-VALUE(36)+VALUE(37) = F3*H

  16. Use of Virtual Work • Joint Equilibrium (Simple Case) • Total work done in joint must equal zero for stability θ 4 5 1 2 3 6 -M1 + M2 = 0 -M3 – M4 + M5 + M6 = 0

  17. Use of Virtual Work • Ten Joint Equilibriums • One for each joint VALUE(24)+VALUE(2)-VALUE(1) = 0 VALUE(4)+VALUE(31)-VALUE(3) = 0 VALUE(16)+VALUE(14)-VALUE(15) = 0 VALUE(30)+VALUE(9)-VALUE(10) = 0 VALUE(33)-VALUE(32) = 0 VALUE(36)-VALUE(35) = 0 VALUE(13)-VALUE(12) = 0 VALUE(7)-VALUE(6)+VALUE(37)-VALUE(27) = 0 VALUE(21)-VALUE(22)+VALUE(26)-VALUE(25) = 0 VALUE(19)-VALUE(18)+VALUE(29)-VALUE(28) = 0

  18. Program Breakdown • Solving Critical Moments • 37 unknown critical moments • 17 levels of structural indeterminacy • Requires 20 indep. equil. equations • 7 beam mechanisms • 3 sway mechanisms • 10 joint equations

  19. Design Against Collapse • Lower Bound Theorem • Structure will not collapse when found to be in a statically admissible state of stress (in equilibrium) for a given loading (P, F, etc.) • Therefore applied loading is less than the load condition at collapse (i.e. P<=Pc and F<=Fc) • Moments to be Safe • Plastic moments set to equal greatest magnitude critical moment in pairing -(Mp)j <= Mi <= (Mp)j for all (i,j) moment pairings

More Related