1 / 21

DO NOW

DO NOW. 3/11/2014. LESSON #. What are the. Focus Point : What are the Types of Punches?. Instructional Objectives: 1. List the purpose of various punches. 2. Describe the different types. 3. Use a specified punch. LESSON #. March 11, 2014. I) Punches:.

babu
Télécharger la présentation

DO NOW

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. DO NOW 3/11/2014 LESSON # • What are the

  2. Focus Point: What are the Types of Punches? • Instructional Objectives: • 1. List the purpose of various punches. • 2. Describe the different types. • 3. Use a specified punch. LESSON # March 11, 2014

  3. I) Punches: punch is a hard metal rod (carbon steel) with a shaped tip at one end and a blunt butt end at the other that is struck by a hammer. • made of hardened tool steel • The part held in the hand is usually octagonal shaped or it may be knurled, in order to prevent the punch from slipping in the hand.

  4. II) Types: A) Center Punch • A sharp pointed tool which is used to provide an indentation in sheet metal prior to drilling. • If the indentation is too deep, the metal will be distorted from the blow of the hammer. However it shall be deep enough to provide a rest

  5. Various Center Punches

  6. Automatic Center Punch • Spring loaded • No ball peen hammer required

  7. B) Pin Punch • Used to remove rivet shank from the hole of a rivet being replaced. • Pin punches come in the exact sizes as the rivets being removed. • Common set of punches – 3/32” 1/8”, 5/32” 3/16” & 1/4”

  8. May also be used to align holes in the skin for faster installation. (Aligning punch) This differs from the pin punch in its length (6-8 inches) It tapers from 1/8” at the point to 3/8” at the shank. Pin Punch Cont’d.

  9. C) Transfer Punch • A special punch used to mark rivet holes when using an old skin as a template for laying out a new skin. • The diameter of the punch is the same as that of a rivet hole, and the end is ground so that the mark on the new skin will be in the actual center of the hole.

  10. Transfer Punch

  11. D) Prick Punch • primarily used for the purposes of layout. • By design it produces a smaller indentation than a center punch, which acts as a useful datum point in layout operations. • indentation made with a prick punch can be enlarged with a center punch • A prick punch usually has a tip, that when viewed on a profile, has sides at a 30-60 degree angle to one another.

  12. PRICK (PUNCH)

  13. E) Hollow Gasket Punch • Used to make gaskets for engines/carburetors - (rubber, cork, leather) • Gasket punches come in sets for various sizes to accommodate standard bolts and studs. • The cutting end is tapered to a sharp edge to produce a clean, uniform hole. Glossary Word: Gasket: Stationary seal between two (2) flat surfaces.

  14. Must be placed on a wood or lead plate to prevent damage of the cutting edge. Now the punch is hit with a hammer, driving it through the gasket material where the holes are required. Gasket Punch

  15. F) Drift Pin (Punch) • Commonly referred to as drift pins and starting punches. Has a long taper from tip to body. • Made to withstand the shock of heavy blows.

  16. May be used to free pins or bolts that are “frozen” in their holes. After the pin or bolt has been loosened the drift pin may be to large to finish the removal, then use a pin punch. DRIFT PIN

  17. What must you wear when using punch?

  18. SAFETY TIP: • Always use the proper punch for the proper job, in order to prevent injury!

  19. Focus Point: What are the Types of Punches? • SUMMARY: (PEP TALK) • 1. What are 3 punches used in Sheet Metal? • 2. Compare the Prick Punch to the center Punch. • 3. Why do we use a gasket punch.

More Related