1 / 46

A-dec 500 INSTALLATION

A-dec 500 INSTALLATION. A-dec 500 Installation. Objectives: To make your installation: Better, Faster, Easier, Safer. A-dec 500 Installation. Refer to the A-dec 500 Installation Guide 86.0400.00 Page ii Equipment Installation Box 1: Chair (Install Guide)

calix
Télécharger la présentation

A-dec 500 INSTALLATION

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. A-dec 500INSTALLATION

  2. A-dec 500 Installation Objectives: To make your installation: • Better, • Faster, • Easier, • Safer.

  3. A-dec 500 Installation • Refer to the A-dec 500 Installation Guide 86.0400.00 • Page ii • Equipment Installation Box 1: Chair (Install Guide) Box 2: Front Mount (contains box 4 for floor box when delivery system is ordered) Box 3: Delivery System Box 5: Support Link Box 6: Assistants Instrumentation Box 7: Lower Arm Box 8: Support Center Box 9: Monitor Mount Box 10: Light

  4. A-dec 500 – 1 Package – 10 boxes Box 1: Chair (Install Guide) Box 2: Front Mount (contains box 4 for floor box when delivery system is ordered) Box 3: Delivery System Box 5: Support Link Box 6: Assistants Instrumentation Box 7: Lower Arm Box 8: Support Center Box 9: Monitor Mount Box 10: Light

  5. A-dec 500 Installation Tips • Be familiar with the all-in-one Installation Instructions 86.0400.00 • Retain with equipment or for future • Numbered boxes: • Indicate the sequence of installation • Allow you to stage equipment • Inventory the modules before starting the install • Full size templates are available parts book p.2: • A-dec 500 Product 86.0904.00 • 511 Chair 86.0905.00 • Floor box 85.0472.00 • Checklist Review

  6. A-dec 500 Installation Tips • Tools Recommended: • Sizes are all SAE, no metric • Hex Key Set (inch) • Phillips & standard screw drivers • Socket wrench set (SAE) • Snap ring tool • Adjustable wrench • Needle nose pliers • Combination wrench set (SAE) • Standard pliers • Diagonal cutters • Hammer • Wire strippers • Level

  7. A-dec 500 Installation Tips • Additional tools that might be helpful: • Chapman tool set • Taps and T handle • Other: • Tape • Extra cable ties • Paper towels or rags • Umbilical stringer (009.015.00) • A-dec Barbs and Fittings Kit (90.1021.00) • 5/16” barb fittings (023.814.01) • 5/16” Sleeves (025.109.00) • Dry Cartridges (38.1783.00) • Wet Cartridges (38.1780.00)

  8. A-dec 500 Installation Tips • Be familiar with the Legris air tubing connectors • Ensure end is cut square • Push into connector fully • Pull on tubing to check grip on tubing • To release tubing from connector, push on outer ring while pulling tubing out • Leave service length to avoid side loading the fitting which could create an air leak • Currently used only on the new 5/16” size air tubing connections.

  9. A-dec 500 Installation Tips • General • Managing Cords and Tubing • Route in spaces provided • Trim tubing to length • Cable tie cords and cables into neat coils • Covers have a low profile and must not have any interference to fit properly • Neatness counts!

  10. A-dec 500 Installation Tips • General • CAUTION: Keep hands/fingers clear – this is a new chair with different pinch points to be aware of • Covers and Upholstery • Leave them off and set, safely, aside until the installation is complete

  11. A-dec 500 Installation Tips • General • Start all the fasteners before tightening any • For example the 3 on the back support • Or the 2 button heads for mounting the Cam • Leveling • Rough – do this to maintain tension or prevent movement • Final – do this when the install is complete and the instruments installed

  12. A-dec 500 Installation Tips • Chair (Box 1) • About the same size as Cascade • Chair box measures 48”L x 30”W x 31”H • Base plate is 26 3/4” W x 34 ½” L • Heavier by 100 lbs • Weight – 400 lbs (packaged) • Use assistance to move • Two people recommended • Dolly or hand truck

  13. A-dec 500 Installation Tips • Chair strapped to Appliance Hand Truck • Leave the two shipping straps in position • Use care when going down or up curbs or steps • Balance carefully

  14. A-dec 500 Installation Tips • Chair • Handholds on seat frame at front and rear • Be sure the shipping straps in place • Do not use the armrests

  15. Moving the chair • Chair Lifter Tools • Support Link Handle • Bolts to support link mount • No P/N as yet • Seat Frame Handle • Schedule 80 PVC • Slides over seat frame • No P/N as yet NEW

  16. A-dec 500 Installation Tips • Full product dimensions are in the Equipment Catalog • 511 chair template available, order 86.0905.00 • Chair should be bolted to floor • Anchor kit 62.0193.00 included • Install Guide page 3

  17. A-dec 500 Installation Tips • Chair • Shipping pin has tag to locate it • Release the swivel brake if the pin is difficult to pull out • Can be left in place to lock out chair swivel if desired • Retain for future use or chair movement. Bags tied to chair for pin and straps. • Power • Air/electric switch connection for Master ON/OFF • ON/OFF button for visual indication of mains power

  18. A-dec 500 Installation Tips • Chair • 3 Tap Feature • Label on base plate • Be patient • Chair has a soft start feature so it seems slow to start moving (down) • Look for the relay LED on the PCB • PCB has test points to operate chair if needed. • Note: this will disable the 3 tap feature but it can be re enabled by cycling mains power

  19. A-dec 500 Installation Tips • Front Mount (Box 2) • Locate hardware kit • Install the Leveling Cam • Raise back up • Raise seat frame up • Install 2 button head leveling cam screws finger tight • Install the 2 leveling studs until only 2 – 3 threads left

  20. Front Mount Installation • Front Mount (Box 2) • The back needs to be full down or the mount will not go on • Tip assembly up to allow mount to hook over the cam • Rough level the front mount at this time using the cam and the 2 leveling studs • Secure the leveling stud flanged washers • Run in the 2 stabilizing screws against the upper structure. • Changed to grade 5 from grade 2 Oct ’04.

  21. Water Bottle on Front Mount • Box 4 is in Box 2 if Delivery System is ordered • Water bottle • Floor box and utilities • Chair air/water manifold • Install the Cap Housing • Hole plug pops out easily when loosened from the bottom • Start button head cap screw for housing • Slide the housing down over the cap screw and tighten the screw • Route tubing through arm and retaining boss • Trim air and water tubing and connect to chair air/water manifold

  22. Delivery System • Mounting the Unit (Box 3) • Lube post (LubriPlate) • Add thrust washer • Mount the Delivery System before routing the tubing and wiring • Install rotation stop ring and large snap ring (using your snap ring pliers) • Tension Adjustment • Use 3/32” hex wrench to add tension to delivery arm

  23. Delivery System Tubing Sheath • Delivery System • Install the Spiral Sheath • Wait until all delivery system plumbing and wiring installed • Start near front and work it forward into the rigid arm • Delivery mount pan covers other end • Rotation stops can be set in front or rear holes depending on arm rotation • Foot Control Sheath • Ensure 1/8” tubings are up so they fit in strain relief correctly

  24. Floor Box • Floor Box Carton (4) • Packaged with front mount inside box 2 or may be separate • Frame and cover • Flush or non flush mounted • 3 or 10 foot umbilical • Utilities • Air gauge is placed in slot in frame • Chair air/water manifold attaches to lift arm • Water bottle and cap assembly

  25. Vacuum and Gravity Adapters • Gravity drain 023.812.000 • Vacuum Adapter 023.816.00 • More connectors in Parts book P/N 023.812.00 P/N 023.816.00

  26. Water Bottle Installation • Lube o-ring on receptacle • Water Bottle - quick and easy installation • Align the bottle seam with the cap • Push the bottle straight up • Rotate bottle to the right (counter clockwise)

  27. Support Link Installation • Support Link (Box 5) • Install leveling bar with dowel pins and leveling bolt • Install support link • Install the top 2 bolts to hold support link in position • Thread the leveling bolt into the support link and rough level • Use jamb nut to lock it against leveling bar • Lock in position with 4 bolts, tighten to 65 ft-lb • Protect the base plate with a piece of cardboard

  28. Support Link Stop Switch • Stop switch assembly (Kit 43.0087.00) • Modify if Lower Arm is to be installed • Make electrical connection at chair stop switch • Mount lower arm to support link • Bearings for top and bottom are Teflon, no lube required • Tighten up on the lower arm set screw adjustment to level

  29. Support Link Stop Switch • Install channel on under side of link • Install the lower arm air tubing in the channel • Install the actuator plates with the stand off screws

  30. Lower Arm • Leveling Lower Arm • Lift end of arm while tightening the screw with a 3/16” hex wrench • Install end cap • Tuck end of stop tube in at bottom of arm

  31. Solids Collector Installation • To Install/Remove the Solids Collector • Solids collector is keyed for removal and replacement • Rotate tubing inlets toward the chair backrest and lift the collector straight up

  32. Drain and Vacuum Fittings • Durr fittings for Drain and Vacuum • Adaptors included to fit stub ups • 25mm (¾”) to ½” brass connector • Secure fit, barbed ends, o-ring seal, and they swivel • Red o-ring 035.053.01 • Lube with silicone grease • Blue retaining clip to secure each connection • Clip 022.090.00

  33. Lift Arm Channel • Drain and vacuum tubing • Vacuum Tubing channel • On right side for the 25 mm vac • Drain Tubing channel • On the left side for the 20 mm drain • Wire clip retains tubing in lift arm channel • Lift arm slots to secure • Foot control • Data cables • Power cords

  34. Hole for Monitor or Light • Knock out hole for monitor post • Don’t use hammer to knock out the hole, you could damage the top • Knock hole out from underneath prior to mounting housing on lower arm • CAUTION: Careful of sharp edges

  35. Cuspidor • Cuspidor Installation • Leave tubing/cords cable tied • Place rotation stop on post and tighten • Place cuspidor on post, allow it to rest on the post box frame part way down • Route tubing/cord bundle through arm and into lift arm • Align cuspidor with arm and lower on to arm being careful not to impact stop ring

  36. Water Bottle on Support Center • Remove cap assembly with 2 screws • Route tubing • Mount bottle housing on support center plate with the 2 screws • Trim tubing and connect to chair air/water manifold

  37. Monitor Installation • Insert keyed trim ring • Insert keyed monitor post into support center • Install rotation stop ring • Install monitor rigid arm to post • Route power cord and video cable

  38. Dental Light Installation • Chair Mounted Dental Light (Box 10) • Flex arm and head with power cord • Rigid arm • Lower straight post • Post adapter • Trim ring • Stabilization ring 28.1574.00 • Power cord extension

  39. Dental Light Installation • Secure light post with screw through keyhole and into post, tighten firmly • Connect light power cord to extension cord in support arm and rout to power supply • Light flex arm and rigid arm need do not need to be lubricated, there is a Teflon bushing inside • Tighten screw to ensure they are locked together

  40. Dental Light Installation • Tighten locking tab retaining screw to ensure ridged arm and flex arm securely locked together

  41. A-dec 500 Installation • Don’t forget: • The delivery system thrust washer • To lube the water bottle o-ring • The cuspidor swivel stop

  42. A-dec 500 Installation • Don’t forget: • The cuspidor trim ring, correctly fitted • The monitor mount rotation stop • The light trim ring

  43. A-dec 500 Install Checklist • Why have one? • All items installed • Chair bolted to the floor • All items work • All Stop Switch functions • All items adjusted • All items programmed • Staff informed about equipment operation and maintenance • In-service clinic performed by dealer sales or technical rep

  44. A-dec 500 Install Checklist • Checklist: • An aid to installation • A reminder for the installer • Retained for reference

  45. A-dec 500 Installation Questions • Which box is the Installation Guide in? • Where is the Floor Box 4 when a Delivery System is included? • What should be the first item you look for in a box? • Where can the Water Bottle be installed? • Can the 3 tap feature be reactivated? How? • On which side of the lift arm does the drain tubing go?

  46. A-dec 500INSTALLATION

More Related