1 / 38

WOOD SHOP HAND TOOLS

WOOD SHOP HAND TOOLS. MEASURING INSTUMENTS. STEEL RULER. TAPE MEASURE. PALM SANDER. Sands with a vibrating motion. TRI-SQUARE.

garth
Télécharger la présentation

WOOD SHOP HAND TOOLS

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. WOOD SHOP HAND TOOLS

  2. MEASURING INSTUMENTS STEEL RULER TAPE MEASURE

  3. PALM SANDER Sands with a vibrating motion

  4. TRI-SQUARE A try square is a woodworking tool used for marking and measuring a piece of wood. The square refers to the tool's primary use of measuring the accuracy of a right angle (90 degrees). To tria surface is to check its straightness, hence the name.

  5. FRAMING SQUARE (STEEL SQUARE) The framing square is used by carpenters because of it’s long arms. It is used to measure distances as well as angles for stairs and rafters.

  6. CARPENTERS OR QUICK SQUARE

  7. COMBINATION SQUARE A combination square is a tool used for multiple purposes in woodworking, stonemasonry and metalworking. It is used to layout or check right and 45° angles.

  8. SLIDING “T” BEVEL A sliding “T” bevel is an adjustable gauge for setting and transferring angles.

  9. MARKING GAUGE The purpose of the gauge is to scribe a line parallel to a reference edge or surface.

  10. BACK SAW/DOVETAIL SAW A backsaw is any hand saw which has a stiffening rib on the edge opposite the cutting edge, allowing for better control and more precise cutting than with other types of saws. Backsaws are normally used in woodworking, for precise work, such as cutting dovetails and miters.

  11. COPING SAW The coping saw is used to cut intricate external shapes and interior cutouts in woodworking or carpentry. It is widely used to cut moldings.

  12. CROSSCUT SAW A crosscut saw is a general term for any saw blade for cutting wood perpendicular (across) the wood grain. Crosscut saws may be small or large, with small teeth close together for fine work like woodworkingor large for course work.

  13. RIP SAW In woodworking, a cut made parallel or with the direction of the grain is known as a rip cut. The cutting edge of each tooth has a flat front edge which is not angled forward or backward. This design allows each tooth to act like a chisel (rather than being knife-like, as with a crosscut saw), preventing the saw from following grain lines, which could curve the path of the saw. By acting like a chisel, the saw can more easily cut across deviating grain lines, which is necessary if a straight cut is to be achieved.

  14. RUBBER MALLET Wooden mallet, usually used in carpentry to knock wooden pieces together, or to drive dowels or chisels. A rubber mallet will not deform the striking end of a metal tool, as most metal hammers would, but it also reduces the force available to drive the cutting edge of a chisel.

  15. CLAW HAMMER A claw hammer is a tool primarily used for pounding nails into, or extracting nails from, some other object

  16. HAND SCRAPER A hand scraper is a tool used to scrape glue, etc. from a surface.

  17. PUTTY KNIFE A putty knife is used to fill nail holes etc. with putty.

  18. TWIST BIT The twist drill bit is the type produced in largest quantity today. It comprises a cutting point at the tip of a cylindrical shaft with helical flutes; the flutes act as a slide for the drilled material to travel up in the spiral tube, until it is finally pushed out of the top.

  19. BRAD POINT BIT Conventional twist drill bits tend to wander when presented to a flat work piece. The center of the drill bit is given not the straight chisel of the twist drill bit, but a spur with a sharp point and four sharp corners to cut the wood. The sharp point of the spur simply pushes into soft wood to keep the drill bit in line.

  20. FORSTNER BIT Forstner bits creates a consistent hole.

  21. BLOCK PLANE A block plane is a small woodworking hand plane. It is designed to cut end grain and is typically small enough to be used with one hand.

  22. JACK PLANE A jack plane is the general-purpose bench plane, used for smoothing edges and for making small smoothing corrections. Jack planes are about 12-15 inches long, and the blade can have either a slightly curved edge for smoothing stock, or a straight edge for jointing stock.

  23. SANDING BLOCK Sanding block creates stability when sanding.

  24. WOOD CHISEL A chisel is a tool with a characteristically shaped cutting edge. The edge may be flat or concaved. It is used for carving or cutting a hard material such as wood, stone, or metal. In use, the chisel is forced into the material, to cut it. The driving force is applied using a malletor hammer. A gouge (concaved), type of chisel, is used, particularly in woodworking to carve small pieces from the material. A gouge typically has a 'U'-shaped cross-section.

  25. COUNTER SINK A countersink is a cone shaped hole cut into a board. A common use is to allow the head of a countersunk bolt or screw, when placed in the hole, to sit flush with or below the surface of the surrounding material

  26. FLAT-BLADE / SLOTTED SCREW DRIVER A screwdriver is a hand-tool for turning (driving) screws.

  27. PHILLIPS SCREW DRIVER The rounded, tapered slots of the Phillips head were deliberately designed for the screwdriver to pop out of the screw head. This helps to prevents stripping damage to the screw threads.

  28. RASP A rasp is a tool used for shaping wood or other material. It consists of a point or the tip, then a long steel bar or the belly, then the heel or bottom, then the tang. The tang is joined to a handle, usually made of plastic or wood. The bar has sharp teeth. Rasps generally cut more coarsely than files.

  29. FILE CARD A file card, which is a brush with metal bristles, is used to clean the file.

  30. HAND SCREW CLAMP Hardwood jaws are perfect for clamping.

  31. AWL An awl is a long, pointed spike. A tool for making holes in wood.

  32. KEYHOLE SAW A keyhole saw is a long, narrow saw used for cutting small, often awkward features in various building materials

  33. BAR (ORANGE) CLAMP An F-clamp, also known as a bar clamp is used in woodworking when a more permanent attachment is needed. F-clamps consists of two horizontal bars joined together by a vertical bar. F-clamps are adjustable which allows for them to be used on larger scale objects.

  34. QUICK CLAMP Quick Clamping Shaft Collars are ideal for light duty applications where frequent setup changes or adjustments are needed.

  35. EYE PROTECTION

  36. ANGLE FINDER The angle finder is used to level (square) the table (work surface) of machinery BEFORE cutting etc. If the table is not square, all of your cuts etc. will not be square. The magnetic bottom attaches to metal surfaces.

  37. PUSH STICK The push stick is a SFETY TOOL used when culling small objects.

  38. NAIL SETTER The nail setter is used to counter sink a finish nail head.

More Related