1 / 20

Metal Forming Course

Metal Forming Course. Open-Die Forging. (a) Ideal deformation of a solid cylindrical specimen compressed between flat frictionless dies. (b) Deformation in upsetting with friction at the die-workpiece interfaces. Metal Forming Course. Impression (Closed) Die Forging.

gillj
Télécharger la présentation

Metal Forming Course

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Metal Forming Course Open-Die Forging • (a) Ideal deformation of a solid cylindrical specimen compressed between flat frictionless dies. • (b) Deformation in upsetting with friction at the die-workpiece interfaces.

  2. Metal Forming Course Impression (Closed) Die Forging • Schematic illustration of stages in impression-die forging. Note the formation of flash, or excess material that is subsequently trimmed off.

  3. Metal Forming Course Load-Stroke Curve in Closed-Die Forging • Typical load-stroke curve for closed-die forging. Note the sharp increase in load after the flash begins to form. In hot-forging operations, the flash requires high levels of stress, because it is thin-that is, it has a small h-and cooler than the bulk of the forging.

  4. Metal Forming Course Piercing Operations Heading • Forging heads on fasteners such as bolts and rivets. These processes are called heading. • Examples of piercing operations.

  5. Metal Forming Course Cogging Operation • Schematic illustration of a cogging operation on a rectangular bar. With simple tools, the thickness and cross-section of a bar can be reduced by multiple cogging operations. Note the barreling after cogging. Blacksmiths use a similar procedure to reduce the thickness of parts in small increments by heating the workpiece and hammering it numerous times.

  6. Metal Forming Course Forging A Connecting Rod • Stages in forging a connecting rod for an internal combustion engine. Note the amount of flash that is necessary to fill the die cavities properly.

  7. Metal Forming Course Features Of A Forging Die Hot-Forging Temperature Ranges

  8. Metal Forming Course Presses Used In Metalworking • Schematic illustration of various types of presses used in metalworking. The choice of the press is an important factor in the overall operation.

  9. Metal Forming Course Flat-And-Shape-Rolling Processes

  10. Metal Forming Course Flat-Rolling Process • Schematic illustration of the flat-rolling process. A greater volume of metal is formed by rolling than by any other metalworking process. • Relative velocity distribution between roll and strip surfaces. Note the difference in the direction of frictional forces. The arrows represent the frictional forces acting on the strip.

  11. Metal Forming Course Roll Bending and Workpiece Spreading • (a) Bending of straight cylindrical rolls because of the roll force. (b) Bending of rolls, ground with camber, that produce a sheet of uniform thickness during rolling. • Increase in the width of a strip (spreading) in flat rolling.

  12. Metal Forming Course Defects In Flat Rolling • Schematic illustration of typical defects in flat rolling: (a) wavy edges; (b) zipper cracks in the center of strip; (c) edge cracks; (d) alligatoring.

  13. Metal Forming Course Shape Rolling • Stages in shape rolling of an H-section part. Various other structural sections, such as channels and I-beams, are also rolled by this process.

  14. Metal Forming Course Ring-Rolling • (a) Schematic illustration of a ring-rolling operation. Reducing the thickness results in an increase in the part’s diameter. (b) Examples of cross-sections that can be formed by ring rolling.

  15. Metal Forming Course Types Of Extrusion • Types of extrusion. (a) direct; (b) indirect; (c) hydrostatic; (d) impact.

  16. Metal Forming Course Extrusion • Schematic illustration of three different types of metal flow in direct extrusion. • Extrusion and examples of products made by sectioning off extrusions.

  17. Metal Forming Course Chevron Cracking • (a) Deformation zone in extrusion, showing rigid and plastic zones. Note that the plastic zones do not meet, leading to chevron cracking. The same observations are also made in drawing round bars through conical dies and drawing flat sheet plate through wedge-shaped dies. (b) Chevron cracking in round steel bars during extrusion. Unless the part is inspected properly, such internal detects may remain undetected and possibly cause failure of the part in service.

  18. Metal Forming Course Drawing • Variables in drawing round rod or wire. • Variation in strain and flow stress in the deformation zone in drawing. Note that the strain increases rapidly toward the exit. The reason is that when the exit diameter is zero, the true strain reaches infinity. The point Ywire represents the yield stress of the wire.

  19. Metal Forming Course Forming Processes For Rocket Casings • The forming processes involves in the manufacture of solid rocket casings for the U.S. Space Shuttle.

  20. Metal Forming Course The End

More Related