1 / 42

TM8106 Optical Networking

TM8106 Optical Networking. Energy Consumption in Optical Networks By Ameen Chilwan. Syllabus: [1] Energy Efficiency For Network Equipment: Two Steps Beyond Greenwashing , Juniper Networks, Whitepaper, 2009.

judah
Télécharger la présentation

TM8106 Optical Networking

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. TM8106Optical Networking Energy Consumption in Optical Networks By Ameen Chilwan Syllabus: [1] Energy Efficiency For Network Equipment: Two Steps Beyond Greenwashing, Juniper Networks, Whitepaper, 2009. [2] Network and Telecom Equipment – Energy and Performance Assessment, Test Procedure and Measurement Methodology, ECR Initiative, Draft 2.1.1, October 04, 2009.

  2. Paper # 1 Energy Efficiency For Network Equipment: Two Steps Beyond Greenwashing. TM8106 Optical Networking - Green Networking

  3. Introduction • Attention drawn to energy footprint of data networking • Due to rising energy costs and environmental standards • Missing verifiable data to support “green” claim • In this paper • Discuss practical aspects of energy efficiency measurement • Define efficiency metric related to equipment energy consumption • Reducing energy-related office & transport expenses • Fairly straight-forward • Reduce the operation cost but has a high initial expenditure • Determines the right point to invest in energy-saving technologies • Current state-of-the-art in network industry • No firm numbers or commitments, but an assorted collection of power management technologies • Not so simple, depends upon many parameters TM8106 Optical Networking - Green Networking

  4. Basics of Moving Data • “An arbitrary message can be represented via units of informational entropy” • Modern computing and communication use “bits” for this • Energy consumption in networking equipment • Due to loss during transfer of electric charges • Caused by imperfect conductors and isolators • Depends upon technology, frequency of transitions, no. of gates • These details are not very interesting to end-users • Instead, a list of features required is maintained, containing: • Minimum packet processing requirements • Scaling parameters (bandwidth, queues, other revenue-generating) • Packaging format • Relative cost TM8106 Optical Networking - Green Networking

  5. Step 1: Efficiency Criteria • In theory, to compare energy consumption: • Sufficient to put two or more devices under the same load and measure their respective power draw • In reality, this is rarely possible • Requires non-trivial investment in test gear • Different devices have different capabilities => not comparable • To define efficiency metric, we normalize energy consumption (E) by effective full-duplex throughput (T) • , ECR is Energy Consumption Rate [watts/Gbps] • E & T come from tests or vendor data, has to be verifiable • ECR is amount of energy (in Joules) required to move an array of data (in bits) across the device. • ECR is a peak metric • Highest performance capacity of the device TM8106 Optical Networking - Green Networking

  6. ECR Metric • Valid differentiator within product class • Equipment with lower ECR use less energy to transfer same amount of data • Unlike light-bulbs, system capacity must be a factor into efficiency estimates • Growing capacity requirement may or may not fit energy budget • Provides unified way of testing • Can be also be used for defining long-term R&D goals • Also mean, specific setting for each customer may not be met • Customers needs 600 Gbps, ECR reported for 1.6 Tbps • Relative ECR standings remain same across wide config range • Assumption that provides compromise between custom and standard settings • Expectation: standard ECR rating will be adequate energy performance estimate TM8106 Optical Networking - Green Networking

  7. Decoding Vendor Datasheets – “T” • Parameters E & T to be collected by same methodology • So, even if ECR not reported by vendor should be possible to be approximated from publicly available data (datasheets, tests) • Platform Throughput • Amount of data platform can process per second • Vendors often report platform capacity, not throughput • Capacity is half-duplex bandwidth in Gbps • Has to be divided by two to get “T” • Not always the case • Some vendors report capacity as theoretical peak utilization based on single isolated metric • This neglects limitations like: line cards that can’t use their whole BW, inter- slot restrictions and other limits • For ECR, “T” should include only effective capabilities • Calculated as sum of capabilities of all the line cards in mesh TM8106 Optical Networking - Green Networking

  8. Decoding Vendor Datasheets – “E” • Several energy metrics in datasheets • Power System Rating [watts or amps] (aka Agent Label) • Site preparation requirements recommended by vendor • Actual consumption maybe fraction of what power supplies deliver • Maximum Energy Consumption [watts] • Vendor’s estimate for highest configuration footprint • Can serve as an upper boundary estimate for power draw • Max energy consumption estimate changes with replacing modules • Component-based Consumption Estimate [watts] • Adding power draws for configured components to make estimate • Arithmetic sum of components ratings never represents real system • Typical (Average) Power Draw [watts] • Vendors are free to report this metric with underpowered config, load profiles that yield best results and so on • Without disclosure of conditions, can’t be used for comparison TM8106 Optical Networking - Green Networking

  9. Advanced Topics • ECR represents performance of fully-configured system running at maximum load • Platform Modularity (Partial configuration) • Energy consumption of modular router/switch is sum of: • Fixed parts “F” (chassis, host system, fabric, clocking) • Variable parts “V” (line cards, ports, physical line drivers) • E = F + V • More efficient in full config are more efficient in partial config too • If not, cross-over point can be found • Absolute Energy Footprint • Relative standings not changed in partial config, but interesting to know how much energy a platform will consume • Component-based energy calculators provided by vendors • ECR method can be adapted to collect and report realistic component footprints in addition to “ratings” TM8106 Optical Networking - Green Networking

  10. Advanced Topics (continued…) • Energy Efficiency and Time Scales • When network not fully loaded, it has on- and off- peak periods • Dynamic power management require measuring energy consumption under variable load • Thus ECR is complemented with Energy Efficiency Rate (EER) • , Ef=full load, Eh=half load, Ei=idle • EER is synthetic and stimulates in area of Barroso’s principle of load proportionality • Any elasticity in energy consumption should not involve pkt drop • Any state change should happen automatically and in real-time • Extended Idle conditions may happen (weekends, day/night cycle) • Maybe useful a device state transition to standby with reduced capacity, i.e. small energy footprint • Transition between active and standby required not to be instant TM8106 Optical Networking - Green Networking

  11. Advanced Topics (continued…) • Metric Accuracy and Practical Impact • Accuracy of ECR and EER reflects averaging and fluctuations • Averaging relates to sampling during test runs • Fluctuations relates to technological deviations • suggested accuracy within range ± 2.5% • Practical ECR/EER advantage can be within 10% or higher • Two ways to express ECR diversity • Monetary difference: related to cost of ownership • A datacenter consumes 100 kW for 5 years, ECR difference of 10% is 438,300 kWh (24*365.25*5) excluding cooling & power conversion • Consider fully burdened consumption, 1.5-3 times of input, 2x overhead, a cost of $ 0.10 and 10% yearly rate increase will give $107,000 for 10% ECR improvement, 200k for 20% and 500k for 50% • Environmental Impact: following Kyoto Protocol (CO2 reduction) • ECR forms basis for equipment selection criteria • Choosing equipment with 10% ECR advantage can mean 1 year advantage TM8106 Optical Networking - Green Networking

  12. Step 2: Design Goals • Energy related improvements in equipment design are: • Organic (passive) • Inline with Dennard’s scaling law: every new generation of network silicon packs more performance in smaller energy budget • Engineered: active energy management, including: • Idle state logic, gate count optimization, memory access algorithm • Some enhancements of both are in step with building networks • E.g. better density, integration and heat management • On the other hand, dynamic power management proportionate to an instant load is a technology with no effect on e.g. capacity • But such technologies form a pool that may improve energy efficiency at pace even faster than Moore’s Law • Return on Investment is not always material • Being a pioneer is also expensive and challenging TM8106 Optical Networking - Green Networking

  13. Step 2: Design Goals (continued…) • Network Design • Guidelines for improved results during network design • Select equipment with best ECR/EER rating • Plan for good system & network utilization • Include rack space, cooling and power conversion in assessment • Do not multiply entities beyond necessity • Consider local energy costs and trends • Conclusion • Modern networks growing faster than Moore’s Law • Offset by reduction in areas like commuting, offline shopping, offline banking and goods manufacturing • Net-centric world: better life quality with less material footprint • So, need more environmental friendly equipment to build networks • Two much-needed steps are: standardize network efficiency, and rise of sustainable network technologies TM8106 Optical Networking - Green Networking

  14. Paper # 2 Network and Telecom Equipment – Energy and Performance Assessment, Test Procedure and Measurement Methodology. TM8106 Optical Networking - Green Networking

  15. Beginning • Purpose • Framework for first-order energy efficiency approximation for • Packet-based network • Telecom equipment • Covers • Peak efficiency, Variable-load efficiency and Idle (statically configurable) energy efficiency • Theoretical Basis • Energy Efficiency = Energy Consumption / Effective Throughput • Basic energy efficiency test: measurement alongside EER • Amount of actual data equal or less than theoretical load • Additional tests for properties like: • Idle (static) energy management, energy management for connected (cascaded) devices and embedded energy monitoring TM8106 Optical Networking - Green Networking

  16. Scope • Efficiency definition suited • For medium to large scale network systems • Less for small office, home, consumer grade devices • TP less relevant • Efficiency metrics can be based on allowances per unit functionality • Tests in this paper applicable to • Core & edge routers, L2/L3 switches, optical packet shelves etc • Anything with performance numbers less than face value of connected ports • Can also be adopted for • equipment with face value of ports same as effective bandwidth (TDM systems, optical converters) • Bandwidth is not a measure of load (control planes, AUTH servers) • Other metric to measure load, e.g. CPU Utilization TM8106 Optical Networking - Green Networking

  17. Test Procedure 1 Energy consumption in relation to dynamically changing load TM8106 Optical Networking - Green Networking

  18. Test Procedure 1 • Packet-based systems based on statistical MUXing • May or may not correspond to theoretical BW as on port face • Simultaneous performance and energy consumption measurements • Under load profile and conditions typical to environment where system under test (SUT) is intended operate • Class-specific requirements in Appendix B • SUT Preparation • Configured according to class requirements • Exposed to conditions as in App. A to settle potential temperature and humidity differences prior to test • Router testing equipment: to simulate load and collect data • AC or DC inline meters to calculate energy consumption TM8106 Optical Networking - Green Networking

  19. Test 1 – Steps • Step 1 (Qualification) • Determine maximum Load (Lmax) sustain SUT at zero pkt loss • Any methodology can be used: binary search, heuristics etc • No time limit for this run • The following runs separated with idle time ≤ 300sec • Step 2 (full load) • Offer Lmax to SUT for 1200 sec, avg consumption E100 found • Step 3 (half load) (can be automated, reset without pkt loss) • Reduce load to Lhalf (=0.5 x Lmax)and run for 1200 sec • Calculate E50 which is avg energy consumption in this period • Load reduced by reducing pkt rate on all configured ports • Not by idling or disconnecting ports • Packet loss resets the test (step1), reset to Lmax should be possible TM8106 Optical Networking - Green Networking

  20. Test 1 – Steps (continued…) • Step 4 (30% load) (can be automated, reset without pkt loss) • Reduce load to L30 (=0.3 x Lmax)and run for 1200 sec • Calculate E30 which is avg energy consumption in this period • Load reduced by reducing pkt rate on all configured ports • Not by idling or disconnecting ports • Packet loss resets the test, reset to any load should be possible • Step 5 (10% load) (can be automated, reset without pkt loss) • Reduce load to L10 (=0.1 x Lmax)and run for 1200 sec • Calculate E10 which is avg energy consumption in this period • Load reduced by reducing pkt rate on all configured ports • Not by idling or disconnecting ports • Packet loss resets the test, reset to any load should be possible TM8106 Optical Networking - Green Networking

  21. Test 1 – Steps (continued…) • Step 6 (idle run) • Remove all the loadand run for 1200 sec • Calculate Ei which is avg energy consumption in this period • Load removal by idling pkt rate on all configured ports • Not by disconnecting or shutting down ports • Packet loss resets the test, reset to any load should be possible TM8106 Optical Networking - Green Networking

  22. Test Procedure 2 (Optional) Energy consumption in relation to statically changing load TM8106 Optical Networking - Green Networking

  23. Test Procedure 2 • Due to extended periods of low utilization • Demonstrate energy saving potential • Pre-requisite is to have Lmax from test 1 • Configuration, preparation, requirement same as test 1 • The following runs separated with idle time ≤ 300sec • Steps • Step 1 (half ports in use) • Reduce to Lhalf (= 0.5 x Lmax) and run for 1200 sec • Measure energy for entire period and find avg P50 • Load reduction by sending traffic at full rate to every second port • Active ports should be evenly mixed with inactive • Block designation (1 line card with all active, other none) not allowed • Packet loss resets to test 1, reset to any higher level not required TM8106 Optical Networking - Green Networking

  24. Test 2 (continued…) • Steps • Step 2 (one quarter of all ports in use) • Reduce to L25 (= 0.25 x Lmax) and run for 1200 sec • Measure energy for entire period and find avg P25 • Load reduction by sending traffic at full rate to every fourth port • Active ports should be evenly mixed with inactive • Block designation (1 line card with all active, other none) not allowed • Packet loss resets to test 1, reset to any higher level not required • Step 3 (one-tenth ports in use) • Reduce to L10 (= 0.1 x Lmax) and run for 1200 sec • Measure energy for entire period and find avg P10 • Load reduction by sending traffic at full rate to every tenth port • Active ports should be evenly mixed with inactive • Block designation (1 line card with all active, other none) not allowed • Packet loss resets to test 1, reset to any higher level not required TM8106 Optical Networking - Green Networking

  25. Test Procedure 3 (Optional) Component level energy footprint (Fc) TM8106 Optical Networking - Green Networking

  26. Test Procedure 3 • A number of configurations for networks are possible • Impractical to test all of them • Perform detailed energy and performance analysis for some • Approximate for the rest of configurations by sum of component-level energy budgets • Less precise compared to actual measurements • Trade-off between operational cost and precise metric values • Vendor builds and publishes • Library of component-level energy consumption • For power budget estimations • Suitable for arbitrary configurations • Detailed measurements not applicable • Concentrates on peak energy performance only TM8106 Optical Networking - Green Networking

  27. Test 3 – Steps • SUT Preparation • Configured according to class requirements including CUT • SUT neither required to be fully loaded nor to bear all modules • CUT that energy and traffic impact of CUT is minimum • Step 1 (Qualification) • Determine maximum Load (Lmax+) sustain SUT at zero pkt loss • Design Lmax+ to exercise all components to highest possible TP • Any methodology can be used: binary search, heuristics etc • No time limit for this run until max load is determined • The following runs separated with idle time ≤ 300sec • Step 2 (full load) • Offer Lmax+ to SUT for 1200 sec, measure energy for the period • average footprint F+ is calculated • Packet loss resets the test to step 1 TM8106 Optical Networking - Green Networking

  28. Test 3 – Steps (continued…) • Step 3 (CUT Removal) • Remove CUT and readjust SUT to compensate • Determine new max load (Lmax-)sustain SUT at zero pkt loss • Design Lmax- to exercise all components to highest possible TP • Step 4 (final measurement) • Offer Lmax- to SUT for 1200 sec, measure energy for the period • average footprint F- is calculated • Packet loss resets the test to step 1 • Energy footprint of CUT is approximated • Fc = F+ - F- • Steps 1-4 repeated as many times as needed • Not applicable for non-redundant components • Only for some components as system chassis and backplane TM8106 Optical Networking - Green Networking

  29. Test Procedure 4 (Optional Functional Test) Embedded energy monitoring capabilities TM8106 Optical Networking - Green Networking

  30. Test Procedure 4 • Real-time energy consumption estimates • pivotal to design and monitor energy conversation policies • Device-level granularity energy utilization reports • not provided by power facilities • Networks to monitor their own energy consumption • by using sensors and embedded probes • Useful to report in parallel with system utilization • Allows for traffic affinity and energy pattern analysis • This test can be done in parallel with • Test 1 and test 2 TM8106 Optical Networking - Green Networking

  31. Test 4 – Steps • Step 1 (Qualification) (can be combinedwith test1 step1) • Same as for test1 step1, Lmax is found • Step 2 (full load)(can be combined with test1 step2) • Offer Lmax to SUT for 1200 sec, avg consumption E100found • Average recorded energy consumption for the period R100 is read from the SUT • Optional: Avg system utilization is recorded U100 • Step 3 (half load)(can be combined with test2 step1) • Reduce to Lhalf(= 0.5 x Lmax) and run for 1200 sec • Measure energy for entire period and find avgP50, R50 and U50 • Load reduction by sending traffic at full rate to every 2ndport • Active ports should be evenly mixed with inactive • Block designation not allowed • Packet loss resets to test 1, reset to any higher level not required TM8106 Optical Networking - Green Networking

  32. Test 4 – Steps (continued...) • Step 4 (25% load)(can be combined with test2 step2) • Reduce to L25 (= 0.25 x Lmax) and run for 1200 sec • Measure energy for entire period and find avgP25, R25 and U25 • Load reduction by sending traffic at full rate to every 4thport • Active ports should be evenly mixed with inactive • Block designation not allowed • Packet loss resets to test 1, reset to any higher level not required • Step 5 (1/10th ports in use)(can be combined with test2 step3) • Reduce to L10 (= 0.25 x Lmax) and run for 1200 sec • Measure energy for entire period and find avgP10, R10 and U10 • Load reduction by sending traffic at full rate to every 10thport • Active ports should be evenly mixed with inactive • Block designation not allowed • Packet loss resets to test 1, reset to any higher level not required TM8106 Optical Networking - Green Networking

  33. Test Procedure 5 (Optional Functional Test) Collateral energy management TM8106 Optical Networking - Green Networking

  34. Test Procedure 5 • Devices can have impact on energy consumption in connected (cascaded) devices • Examples include: • Ability to control power states in Power over Ethernet (PoE) • Ability to assist power states in LAN-connected devices • Ability to control IP and non-IP devices via remote control mechanisms TM8106 Optical Networking - Green Networking

  35. Effective TP Calculation • Lmax converted into full-duplex TP Tf (in Gbps) • To normalize SUT energy consumption to performance • First method: • Lmax reported by traffic generator as a combination of egress packet-per-second rate and packet size compared to the load. • For variable pkt size: average proportion is computed • All applicable minimum L2 & L1 overhead added to compute effective wire rate • Example: • SUT is eth switch, 10 x 10 GbE ports @ 7,291,702 fps, 64 B/frame • Implies 7,291,702 pps • Tf = 10 x 7,291,702 x 8 x (64 + 1 + 7 + 12) = 49.000237440 Gbps • (1 + 7 + 12): accounts for eth start of frame, preamble, min interpkt gap TM8106 Optical Networking - Green Networking

  36. Effective TP Calculation (continued…) • Second method: • Lmax reported tester equipment itself as highest achieved utlization on per-port basis (in percentage) • Line rates multiplied by port utilization to get final data rate • Example: • SUT is MPLS edge platform, 10x10 GbE ports each on core & access • Frames forwarded towards core with 100% utilization • Frames forwarded towards access with 99.22% utilization • Data rate for 10 GbE is 10,000 Mbps • Tf = 10 x 10,000 x 1.0 + 10 x 10,000 x 0.9922 = 199.22 Gbps • Example: • SUT is eth switch with 8 GbE ports opearting at • 100% line utilization when configured for VLAN • 90% line utilization when not configured for VLAN • Result from 2nd case is used as eth switches don’t need VLAN headers TM8106 Optical Networking - Green Networking

  37. Results Representation • Array of results obtained from test 1-4 form energy “passport” of the SUT and can be used for evaluation and energy planning purposes • Base Metrics and Device Comparisons • Most straight-forward metric is to normalize energy consumption to the highest sustained throughput recorded • [W/Gbps] • Unlikely to obtain efficiency numbers over sustained intervals • Due to off- (low utilization) and on- (burst) peak periods that cause provider to size on the higher end of traffic profile and lose energy efficiency during off-peak times • Instead, providers can optimize efficiency using middle of their load band • [W/Gbps] • ECR-VL is the measure of dynamic energy management • ECR-VL rating should be close to ECR following Barroso’s principle TM8106 Optical Networking - Green Networking

  38. Energy Bill Estimates • Cost of operation over projected lifetime • N is projected no. of years, CkWhj is cost of kWh in year of operation • This method gives estimate based on automatic (variable-load) energy management capabilities of reference system • Modest, but provide lossless operation under all conditions • Alternative cost estimate • Build upon static (idle-load) energy saving capabilities of device • Example: a switch downgraded to 25% at night and 10% on Sun. • Both systems are complementary & work on different time intervals • Relative slow configuration change, not applicable to burstyenv. • Requires personnel to take care of policy-driven degradation TM8106 Optical Networking - Green Networking

  39. Site Planning • Providers use Agency Labels provided by vendors • Ill-suited because call for energy reservation at highest end • Makes it confusing whether device will work in case on-site power rating is less that this value • Useful resources for site planning • Value E100 • describes average SUT energy consumption under highest possible load • Provides upper boundary for energy requirements • If E100 not provided • can be approximated from sum of required components • Provided that component footprint Fci were published TM8106 Optical Networking - Green Networking

  40. Functional Compliance • Tests 4&5 are intended for functional compliance testing • Only pass/fail criteria • In test 4, externally measured consumption values (E100, P50, P25, P10) should be compared to (R100, R50, R25, R10) reported by SUT • Adjusted result should be in acceptable range of effective consumption (±10% or less) • Upon vendor’s approval an offset R can be added to compensate electronics not covered by embedded power monitoring circuitry • Externally recorded load L should correlate to utilization U • Where Lmax = 100% SUT Utilization • Static offset can also be added in this case, upon vendor’s approval • Knowledge of system w.r.t time crucial for planning static energy management routines • Test 5 describes value-added functionality that might be in SUT TM8106 Optical Networking - Green Networking

  41. Reporting Format • Results shall be fully reproducible by any laboratory • Thus has to include at least the following documentation • All SUT software versions, hardware board revisions and device configurations used during the test. • All commands applied for static config to SUT or run-time queries • Traffic generator tool passports, actual voltage in power feeds and ambient (environmental) conditions at test side • The test setup should fully described, including topology, the choice of offered load structure and test actions within a range of possible choices. TM8106 Optical Networking - Green Networking

  42. TM8106 Optical Networking - Green Networking

More Related