1 / 20

Soil Exploration Part II

Soil Exploration Part II. T.E. Civil 2009-2010 G.E.- I. Topics Covered. Introduction Methods of investigation Methods of boring Soil samplers and sampling Location and number of pits and borings Penetrometer tests Borehole logs Geophysical methods. Methods of Sampling. Samples

kasa
Télécharger la présentation

Soil Exploration Part II

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Soil Exploration Part II T.E. Civil 2009-2010 G.E.- I

  2. Topics Covered • Introduction • Methods of investigation • Methods of boring • Soil samplers and sampling • Location and number of pits and borings • Penetrometer tests • Borehole logs • Geophysical methods

  3. Methods of Sampling Samples Disturbed Undisturbed (The structure of the soil is disturbed (The true in-situ structure and water content to a considerable degree) is retained as closely as possible) Remoulded Representative Block Drive Wash

  4. Methods of Sampling • Disturbed samples used for determining index properties (ex. gsd, consistency, etc.) • Undisturbed samples used for determining engineering properties (ex. Density, water content, shear strength parameters, etc.) • Wash samples obtained from wash boring water or mud. • Representative sample retains all constituents of the soil, but is disturbed from natural state and structure. (ex. Split spoon sampler) • Block samples are carved out form sides or bottoms of excavations, sealed in a box and taken to lab. • Open drive samplers consist of thin walled tubes which are driven or pushed into the soil at the bottom of the hole. (ex. Shelby Tube sampler)

  5. Undisturbed Samples

  6. Methods of Sampling • Thin-wall open-tube samplers (Shelby Tube Samplers) are used for soils that are particularly sensitive to sampling disturbance. They are suitable for fine soils up to a firm consistency, and free from large particles. • Shelby Tubes are available in carbon steel and in stainless steel. Usual diameters are 3" or 4" OD.

  7. Shelby Tube

  8. Split spoon sampler IS:9640-1980

  9. Sketch of split spoon sampler

  10. Requirements to minimize disturbance to samples Area ratio = (D2w-D2e) x 100% D2e Area ratio should be as low as possible. (<10%). It represents the amount of soil displaced. Inside clearance = (Ds-De) x 100% ratioDe . Methods of Sampling

  11. Methods of Sampling • The inside clearance allows elastic expansion of the sample and minimizes frictional drag on the sample. • The inside clearance should be between 0.5% to 3%. • The outside clearance = (Dw-Dt) x 100% ratioDt • Outside clearance is necessary to reduce the driving force and resistance to withdrawal. • The outside clearance should be between 0% and 2%. • Diameter of samples should not be less than 38mm. (Generally between 50-150mm). • Piston sampler (Osterberg sampler) not covered. Please refer to any book.

  12. Rock coring • Sampler consists of core barrel and bit is coring bit. • Core barrel – single tube or double tube of various dia: EX, AX, BX, NX, etc. • Recovery = Length of sample recovered x 100% Length of run • RQD = Length of samples >= 4” x 100 % Length of run

  13. SPT (Standard Penetration Test) • IS:2131 – 1981 Method for Standard Penetration Test for Soils. • Most important and most commonly used field test • Typical equipment: drill rig, split spoon sampler, hammering equipment, casing pipe.

  14. SPT Procedure • Procedure: • Drive a section of casing pipe. • Complete wash boring and clean the hole • Replace driving bit by split spoon sampler at the bottom end of the driving rod • Drive the sampler by dropping a hammer of 63.5kg weight through a height of 75 cm • The number of blows required to penetrate three successive lengths of 15 cm are noted. • The first 15 cm drive is considered as seating load and is ignored. The total number of blows required to penetrate the remaining 30 cm is called the blow count or penetration number N. • Raise the sampler to the surface, open it and extract the sample. • Drive the next length of casing and repeat the process until required depth is reached. • At the end of the borehole, note the gwt after it stabilizes and then backfill the borehole.

  15. Corrections to N value • Overburden Correction applied to N value based on chart by Peck, et. al. (varies from 0.45 to 2) • N’=Cn * N where Cn is correction factor • Correction due to dilatancy for fine sand and silt below gwt having N’ > 15 • N” = 15 + 0.5*(N’-15)

  16. Correlations between N values and soil properties

  17. Correlations between N values and soil properties

  18. Other test methods • DCPT – Dynamic cone penetration test IS:4968 -1976 (Method for subsurface sounding for soils: Parts I and II) • CPT – Static Cone Penetration Test (Method for subsurface sounding for soils: Part 3 Static cone penetration test) • Plate Load Test (Method of Load Test on Soils)

  19. Borelog and geotechnical investigation report .

More Related