1 / 9

PAN Feasibility: The BodyLAN TM Experience

PAN Feasibility: The BodyLAN TM Experience. GTE Internetworking - BBN Technologies 733 Concord Avenue Cambridge, MA 02138 Rick LaRowe (rlarowe@bbn.com). I N T E R N E T W O R K I N G POWERED BY BBN. Personal Area Networks. Driving requirements include: Very low power consumption

keahi
Télécharger la présentation

PAN Feasibility: The BodyLAN TM Experience

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. PAN Feasibility:The BodyLANTM Experience GTE Internetworking - BBN Technologies 733 Concord AvenueCambridge, MA 02138 Rick LaRowe(rlarowe@bbn.com) I N T E R N E T W O R K I N G POWERED BY BBN Rick LaRowe, GTE

  2. Personal Area Networks Driving requirements include: • Very low power consumption • Very small devices (including peripherals, sensors, etc.) • Easy integration into devices (minimal SW) • Cross-network interference tolerance • Very low cost Simplifying characteristics include: • Data rate requirement is relatively low • Range is short (2-10 meters) Rick LaRowe, GTE

  3. PEA PEA HUB PEA PEA PEA BodyLAN Topology • For simplicity, a STAR topology is employed. • The Hub is at the centerand runs the show. • Around the edge arePersonal ElectronicAccessories (PEAs) Rick LaRowe, GTE

  4. S B H T T E E A O C A PDU A T A K R C C R DATA D E C K E O E S N N R P Key Characteristics • Simple TDMA structure: • Cross-network interference: • CDMA-like burst spacing using Optical Orthogonal Coding • Frequency agility Rick LaRowe, GTE

  5. Other Key Attributes • PAN requirements demand only small networks; 7-bit MAC address is sufficient. • Dynamic device attachment supported via a form ofslotted Aloha layered on top of the TDMA structure. • Ad Hoc networking easily supported: any device can function as a Hub. • Prioritorized bandwidth allocation is easily achieved via Hub token allocation mechanism. (Partly demand-driven via Status Response messages from PEAs.) • Design readily enables single-chip Data-Link and MAC implementation. Rick LaRowe, GTE

  6. PPC 403 BodyLAN BodyLAN PC, HPC, RS-232 Host Digital RF or Processor Control Transceiver Sensor Proof-of-Concept Demo • Demonstrated with two real applications in early 1998. • Basic structure: • PowerPC (PPC) runs the device driver and protocol stack. (PPC selected since needed to run Inertial Navigation code used by a demonstration sensor PEA.) • Digital board contains an Altera PLD with MAC layer implementation and debug logic. • RF transceiver a small discrete implementation. Rick LaRowe, GTE

  7. Host Processor & Digital PLD Rick LaRowe, GTE

  8. Characteristics of POC Demo • Fully operational, with good performance • Dynamic attachment / detachment works • Dynamic bandwidth allocation over TDMA structure • 100mA with PowerPC @ 25MHzTransceiver draws 10mA when running (xmit/recv)PLD draws about 15mA (ASIC est. @ 500mA)(lots of debug and test support, no board-level optimization) • Range adjusted to about 2m, have run up to about 5m Rick LaRowe, GTE

  9. The End Any Questions? Rick LaRowe, GTE

More Related