1 / 61

FIRE SERVICE FORCED ENTRY

FIRE SERVICE FORCED ENTRY. Swinging cutting tools. use a proper stance use short strokes swing no higher than your shoulders angle your strikes be aware of your surroundings people wires, etc. Keep tool head in sight while swinging. BOLT/WIRE CUTTERS. Bolt Cutters cables, chains, pins

sandra_john
Télécharger la présentation

FIRE SERVICE FORCED ENTRY

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. FIRE SERVICE FORCED ENTRY

  2. Swinging cutting tools • use a proper stance • use short strokes • swing no higher than your shoulders • angle your strikes • be aware of your surroundings • people • wires, etc. • Keep tool head in sight while swinging

  3. BOLT/WIRE CUTTERS • Bolt Cutters • cables, chains, pins • ANYTHING NOT CASE HARDENED • Wire Cutters • De-energized ONLY

  4. HALLIGAN BAR • Deputy Chief Hugh Halligan in the 40’s • 3 prying tools, each w/ striking surface • ADZE end • Pick, hook or horn • forked end • New standard, one piece construction

  5. Halligan uses • Pick • spot ventilation points • manhole covers • padlocks • ladder braces • footing on roofs

  6. Halligan uses • Fork • gas meter shut offs • numerous prying situations • limited to user

  7. HALLIGAN BAR USES The HOOK may be buried into a roof for: 1- A step 2- An inspection hole

  8. The key to all prying tools is:LEVERAGE

  9. MAINTENANCE • WOOD • Inspect for cracks, splinters, etc. • Sand rough spots • Wash warm water simple green • Linseed oil on handle, no paint or varnish • Check head tightness • FIBERGLASS/NUPLA • Wash w/ simple green and warm water • Check head for tightness

  10. MAINTENANCE • Edges • Inspect for burrs, nicks. FILE as needed • DO NOT GRIND • File to a medium sharpness • Metal Surfaces • Keep rust free • Lightly oil • DO NOT PAINT

  11. GOLDEN RULES OF FORCED ENTRY • TRY BEFORE YOU PRY • Do a good door size-up • Force obstacles in the direction that they were meant to travel • THINK • Use leverage

  12. GOLDEN RULES OF FORCED ENTRY (CONT.) • Think about other safer, faster ways in • Work tools… DON’T LET THEM WORK YOU FORCE A DOOR, CHOCK THAT DOOR

  13. Door Size Up

  14. SECTIONAL or FOLDING • Center latch usually controls two slide locking bar on either side of door • Pry up from the center • Remove a panel to access the latch • Usually secondary locks on door • Find easier way in

  15. Pivoting or Overhead Slab Doors • Center latch usually controls two slide locking bar on either side of door • Pry out at both sides • Make sure path is clear to travel • Remove a panel to access the latch • Usually secondary locks on door • Find easier way in

  16. Rolling Steel Doors • Usually a security type door • Locked numerous ways • Use metal cutting blade • Cut triangle • One vertical cut, remove slats of doors • Look for handle or motor housing during size-up

  17. FIRE DOORS • Fire doors protect door openings in walls that are required to be rated as a fire barrier • SLIDING • HORIZONTAL AND SLIDING • SWINGING • SINGLE AND DOUBLE • OVERHEAD ROLLING • Most difficult to force

  18. FIRE DOORS OPERATE: • Self Closing • when opened, it self closes. Duh • Automatic • normally open, closes when hold-open device trips BLOCK OPEN FORCED FIRE DOORS

  19. TYPES OF LOCKING DEVICES • Rim locks- installed ON a door, near edge (RIM). Usually as a second lock • Mortise locks- installed INSIDE a door cavity by a locksmith or built in the door • Tubular deadbolt- Combo of BOTH. Controls a deadbolt that rides a hollow tube inside the door edge. Keyed on back or turn knob.

  20. TYPES OF LOCKING DEVICES • KEY-in-KNOB- Typical interior household knob/lock. • Auxiliary lock- Pad locks, drop bars, slide bolts or any combo. thereof

  21. THROUGH THE LOCK METHODS • USING THE “K” TOOL

  22. Use channel locks or vise grips to attempt to loosen a mortise cylinder lock

  23. Use VISE GRIPS to loosen and remove a mortise cylinder lock • If a lock is inaccessible with a “K” tool, drive a straight slot into the key hole and loosen with a pair of VISE GRIPS

  24. Place the tool over the lock • Drive the tool onto the lock with a striking tool • PRY the lock in the opposite direction

  25. Tubular locks may call for different tools to unlock

  26. SHOVE KNIFE • Flat steel • Easy to make • Very useful on doors that swing out

  27. Use vise grips to maintain control of a door • Use to control a padlock with a irons

  28. Additional Forcible EntryTechniques • The following slides will be discussed in detailed during the in service training.

  29. HORIZONTAL DOOR CUTThis cut usually avoids all locking devices and security bars.

More Related