1 / 83

Physical Layer – Transmission Media

Physical Layer – Transmission Media. Transmission Media. Two basic formats Guided media : wires, fiber optics Medium is important Unguided media : wireless, radio transmission Antenna is important Each have tradeoffs over data rate, distance Attenuation : weakening of signal over distance.

seth-mendez
Télécharger la présentation

Physical Layer – Transmission Media

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Physical Layer – Transmission Media

  2. Transmission Media • Two basic formats • Guided media : wires, fiber optics • Medium is important • Unguided media : wireless, radio transmission • Antenna is important • Each have tradeoffs over data rate, distance • Attenuation : weakening of signal over distance

  3. Mini Electromagnetic Review • Take a sound wave… Frequency (hz) = Number of cycles/second With a constant wave velocity, frequency = velocity / wavelength For electromagnetic waves, f = c / w ; c = speed of light

  4. Mini Electromagnetic Review Same principle with electrical waves: Station at 88.1 FM = 88.1 Mhz 88100000 = 3.0 * 10^8 / w w = 3.0 * 10^8 / 88100000 = 3.4 meters Time to travel this far is 1/f or 0.000000011 seconds

  5. Electromagnetic Spectrum

  6. Guided Transmission Media • Twisted Pair • Coaxial cable • Optical fiber Attenuation Coax Twisted Pair Fiber Optics 1Khz 1Mhz 1Ghz 1Thz 1000Thz Frequency

  7. Twisted Pair Pair of copper wires constitutes a single communication link. Twists minimize the effects of electromagnetic interference - emit less emag energy - less susceptible to emag energy

  8. Twisted Pair - Applications • Most common medium • Telephone network • POTS • Between house and local exchange (subscriber loop), also called the end office. From the end office to Central Office (CO) class 4  CO class 1 via Public Switched Telephone Network (PSTN) • Within buildings • To private branch exchange (PBX) • For local area networks (LAN) • 10Mbps or 100Mbps • Possible to rev up to 1Gbps – Gigabit Ethernet

  9. Twisted Pair - Pros and Cons • Cheap • Easy to work with • Can use as digital or analog • Limited bandwidth/data rate • Generally 1Mhz and 100Mbps but up to 1 Ghz • Short range • 2km for digital, 5km for analog • Direct relationship between data rate and range • Gigabit Ethernet • 1000Mbps over 4 Cat5 UTP up to 100 meters • IEEE 802.3ab standard in 1999 • 1000Mbps over 1 Cat5 UTP up to 24 meters

  10. Unshielded and Shielded TP • Unshielded Twisted Pair (UTP) • Ordinary telephone wire • Cheapest • Easiest to install • Suffers from external EM interference • Shielded Twisted Pair (STP) • Metal braid or sheathing that reduces interference • More expensive • Harder to handle (thick, heavy)

  11. UTP Categories • Cat 1 • Used for audio frequencies, speaker wire, etc. Not for networking. • Cat 2 • Up to 1.5Mhz, used for analog phones, not for networking • Cat 3 • EIA 568-A Spec from here on up • up to 16MHz • Voice grade once common in offices, 10 Mb networks • Twist length of 7.5 cm to 10 cm • Cat 4 • up to 20 MHz • Not frequently used today, was used for Token Ring

  12. UTP Categories Cont. • Cat 5 • up to 100MHz • Twist length 0.6 cm to 0.85 cm • Commonly pre-installed in new office buildings • Cat 5e “Enhanced” • Up to 100Mhz • Specifies minimum characteristics for NEXT (Near End Crosstalk) and ELFEXT (Equal level far end crosstalk) • Coupling of signal from one pair to another • Coupling takes place when transmit signal entering the link couples back to receiving pair, i.e. near transmitted signal is picked up by near receiving pair • Cat 6 • Standard up to 250Mhz; heavier, up to 100 meters • Cat 6a • Standard up to 500Mhz

  13. Typical Usage of Twisted Pair

  14. Coaxial Cable Shielded, less susceptible to noise and attenuation than Twisted Pair.

  15. Coaxial Cable Applications • Most versatile medium • Television distribution • Cable TV • Long distance telephone transmission • Can carry 10,000 voice calls simultaneously • Being replaced by fiber optic • Short distance computer systems links • Local area networks • More expensive than twisted pair, not as popular for LANs

  16. Coaxial Cable Characteristics • Analog – Broadband Coaxial Cable • Amplifiers every few km, closer if higher frequency • Up to 500MHz • Cable TV, Cable Modems (~10Mbps) • Digital – Baseband Coaxial Cable • Repeater every 1km • Closer for higher data rates

  17. Coaxial Cable LAN

  18. Optical Fiber Breakthrough in data transmission systems! Core: Thin strands of glass Cladding: Glass with different optical properties than core Jacket: Plastic/Insulation

  19. Optical Fiber - Benefits • Greater capacity • Data rates of hundreds of Gbps • Tbps demonstrated using WDM • Smaller size & weight • Order of magnitude smaller than TP/Coax • Lower attenuation • Electromagnetic isolation • Not vulnerable to interference, impulse, crosstalk! • Greater repeater spacing • Often 10’s of kilometers • Hard to tap

  20. Optical Fiber Transmission Modes Rays at shallow angles reflect; multiple propagation path spreads signal out over time Gradient refraction in core allows light to curve helically, more coherent at end Shrink core to allow only a single angle or mode, light reflect in only one pattern

  21. Wireless or Radiated Transmission • Unguided media • Transmission and reception via antenna • Desirable to make antenna one-quarter or one-half the wavelength • Directional • Focused beam • Careful alignment required • Omnidirectional • Signal spreads in all directions • Can be received by many antennas

  22. Frequencies • 2GHz to 40GHz • Microwave • Highly directional • Point to point • Satellite • 30MHz to 1GHz • Omnidirectional • Broadcast radio • 3 x 1011 to 2 x 1014 • Infrared • Local • Higher frequencies  Higher data rates

  23. Terrestrial Microwave • Typically parabolic dish, focused beam, line of sight • Max distance between antenna: d=7.14 * Sqrt(hK) ; K=4/3, ; h=antenna ht in meters ; d=distance in km so two 1 meter antenna can be 7.14*Sqrt(4/3)=8.2 km apart • Applications • Long haul telecommunications, television. May need repeaters • Short range for BN or closed-circuit TV

  24. Terrestrial Microwave • Data rate increases with frequency • 2 Ghz Band  7 Mhz Bandwidth  12 Mbps • 6 Ghz Band  30 Mhz Bandwidth  90 Mbps • 11 Ghz Band  40 Mhz Bandwidth  135 Mbps • 18 Ghz Band  220 Mhz Bandwidth  274 Mbps • Attenuation • Loss varies with the square of the distance • TP/Coax: loss varies with log of distance / linear in dB • Therefore, we don’t need as many repeaters with microwave • Interference and Raindrop Attenuation • Frequency bands strictly regulated • Use lower frequency to avoid raindrop problem

  25. Satellite Microwave • Satellite is relay station • Satellite receives on one frequency, amplifies or repeats signal and transmits on another frequency/frequencies (transponder channels) • Typically geo-stationary orbit • Height of 35,784km or 22,236 miles • 4 degree spacing in 4/6Ghz Band • 3 degree spacing in 12/14 Ghz Band • Applications • TV, telephone • Private business networks • VSAT (Very Small Aperture Terminal) • Large corp. with distributed sites • Small receiver to Ku-band satellite to Big earth hub • Used by RCA in late 1994 for Direct Broadcast System

  26. Satellite Transmission Characteristics • Optimum Frequency Range 1-10Ghz • Below 1Ghz, natural noise. Above 10Ghz, attenuation from the atmosphere • Most applications use the 5.925-6.425 Ghz range uplink, 4.2-4.7Ghz range downlink (4/6 Ghz Band) • Propagation delay • 35784000m / 3.0 * 108 m/s  0.12 seconds one way • About quarter second propagation delay round trip, noticeable for phone conversations, problem for two-way communications • Error /flow control? • Low orbit satellites a solution? (Iridium, Tachyon)

  27. Broadcast Radio • 30Mhz to 2 Ghz • Omnidirectional • Use loop or wire antenna instead of dish • Applications • Range covers FM radio, UHF and VHF television • 802.11b operates in the 2.4Ghz ISM band • Due to lower frequencies than microwave, less problems with attenuation • Same equation for antenna distance, attenuation as microwave • Drawbacks • Suffers from multipath interference, Reflections • Possible security concerns

  28. Infrared • Modulate noncoherent infrared light • Line of sight (or reflection) • Blocked by walls • Problems • Short range, usually 50-75 feet maximum • Low speed, 1-4 Mbps • e.g. TV remote control, IRD port • For networks, not generally used due to the need for direct line-of-sight; was used to connect hubs

  29. Media Selection Guided Media Radiated Media Network Transmission Error Media Type Cost Distance Security Rates Speed Twisted Pair LAN Low Short Good Low Low-high Coaxial Cable LAN Mod. Short-Mod Good Low Low-high Fiber Optics any High Mod.-long V. Good V.Low High-V.High Network Transmission Error Media Type Cost Distance Security Rates Speed Radio LAN Low Short Poor Mod Low Infrared LAN, BN Low Short Poor Mod Low Microwave WAN Mod Long Poor Low-Mod Mod Satellite WAN Mod Long Poor Low-Mod Mod

  30. Carriers and Modulation First, review of digital transmission of digital data

  31. Baseband Transmission Digital transmission is the transmission of electrical pulses. Digital information is binary in nature in that it has only two possible states 1 or 0. Sequences of bits encode data (e.g., text characters). Digital signals are commonly referred to as baseband signals. In order to successfully send and receive a message, both the sender and receiver have to agree how often the sender can transmit data (data rate). Data rate often called bandwidth – but there is a different definition of bandwidth referring to the frequency range of a signal!

  32. Baseband Transmission With unipolar signaling techniques, the voltage is always positive or negative (like a dc current). In bipolar signaling, the 1’s and 0’s vary from a plus voltage to a minus voltage (like an ac current). In general, bipolar signaling experiences fewer errors than unipolar signaling because the signals are more distinct.

  33. Baseband Transmission

  34. Baseband Transmission Manchester encoding is a special type of unipolar signaling in which the signal is changed from a high to low (0) or low to high (1) in the middle of the signal. • More reliable detection of transition rather than level • consider perhaps some constant amount of dc noise, transitions still detectable but dc component could throw off NRZ-L scheme • Transitions still detectable even if polarity reversed Manchester encoding is commonly used in local area networks (ethernet, token ring).

  35. Manchester Encoding

  36. ANALOG TRANSMISSION OF DIGITAL DATA Analog Transmission occurs when the signal sent over the transmission media continuously varies from one state to another in a wave-like pattern. e.g. telephone networks, originally built for human speech rather than data. Advantage for long distance communications: much less attenuation for analog carrier than digital

  37. Digital Data to Analog Transmission Before we get further into Analog to Digital, we need to understand various characteristics of analog transmission.

  38. PeriodicSignals

  39. Sine Wave • Peak Amplitude (A) • maximum strength of signal • volts • Frequency (f) • Rate of change of signal • Hertz (Hz) or cycles per second • Period = time for one repetition (T) • T = 1/f • Phase () • Relative position in time, from 0-2*pi • General Sine wave

  40. Varying Sine Waves

  41. Wavelength • Distance occupied by one cycle • Distance between two points of corresponding phase in two consecutive cycles •  = Wavelength • Assuming signal velocity v •  = vT • f = v • c = 3*108 ms-1 (speed of light in free space)

  42. Frequency Domain Concepts • Signal usually made up of many frequencies • Components are sine (or cosine) waves • Can be shown (Fourier analysis) that any continuous signal is made up of component sine waves • Can plot frequency domain functions

  43. Addition of FrequencyComponents Notes: 2nd freq a multiple of 1st 1st called fundamental freq Others called harmonics Period of combined = Period of the fundamental Fundamental = carrier freq

  44. FrequencyDomain Discrete Freq Rep: Any continuous signal can be represented as the sum of sine waves! (May need an infinite number..) Discrete signals result in Continuous, Infinite Frequency Rep: s(t)=1 from –X/2 to X/2

  45. Data Rate and Bandwidth • Any transmission system has a limited band of frequencies • This limits the data rate that can be carried • Spectrum • range of frequencies contained in signal • Absolute bandwidth • width of spectrum • Effective bandwidth • Often just bandwidth • Narrow band of frequencies containing most of the energy

  46. Example of Data Rate/Bandwidth Want to transmit: Let’s say that f=1Mhz or 106 cycles/second, so T= 1microsecond Let’s approximate the square wave with a few sine waves:

  47. Ex(1): Sine Wave 1 Bandwidth=5f-f =4f If f=1Mhz, then the bandwidth = 4Mhz T=1 microsecond; we can send two bits per microsecond so the data rate = 2 * 106 = 2Mbps

  48. Ex(2): Sine Wave 1, Higher freq Bandwidth=5f-f =4f If f=2Mhz, then the bandwidth = 8Mhz T=0.5 microsecond; we can send two bits per 0.5 microseconds or 4 bits per microsecond, so the data rate = 4 * 106 = 4Mbps Double the bandwidth, double the data rate!

  49. Ex(3): Sine Wave 2 Bandwidth=3f-f =2f If f=2Mhz, then the bandwidth = 4Mhz T=0.5 microsecond; we can send two bits per 0.5 microseconds or 4 bits per microsecond, so the data rate = 4 * 106 = 4Mbps Still possible to get 4Mbps with the “lower” bandwidth, but our receiver must be able to discriminate from more distortion!

More Related