SlideServe
Télécharger Obtenir Pro
Menu
Accueil Pro
Préférences
ApparenceLight Aide et commentaires
© SlideServe · v2026

How to Square A 2x4

sharne avatar
sharne
13 diapositives · 1.1K Views · May 12, 2012

How to Square A 2x4. Marc Nutini. Step 1. I will demonstrate the steps of how to square a warped and twisted 2x4x3’ piece of stock. The first step to squaring a board is picking the piece you want. Examples (Oak, Pine, Maple). Step 2.

#radio propagation #mochi #magic square #latin square #do #amount #lame #fair
How to Square A 2x4 - slide 1
01 / 13How to Square A 2x4
1 / 17

Télécharger la présentation

How to Square A 2x4
Une image / un lien ci-dessous est fourni (tel quel) pour télécharger la présentation

Politique de téléchargement : le contenu du site vous est fourni TEL QUEL pour votre information et votre usage personnel ; il ne peut être vendu, concédé sous licence ni partagé sur d’autres sites sans l’accord de son auteur.Le contenu vous est fourni TEL QUEL, pour votre information et votre usage personnel uniquement. Téléchargez la présentation en cliquant sur ce lien. Lors du téléchargement, si vous ne parvenez pas à télécharger une présentation, l’éditeur a peut-être supprimé le fichier de son serveur.Pendant le téléchargement, si vous ne parvenez pas à obtenir une présentation, le fichier a peut-être été supprimé par l’éditeur.

F I N

Plus de contenu associé

Transcription de la présentation

  1. How to Square A 2x4 Marc Nutini

  2. Step 1 • I will demonstrate the steps of how to square a warped and twisted 2x4x3’ piece of stock. • The first step to squaring a board is picking the piece you want. Examples (Oak, Pine, Maple)

  3. Step 2 • Set the jointer so it cuts about 1/32-1/16 of an inch per pass. • Take the piece and place it wide side down and run it through the jointer. • It’s important to apply even pressure to the board as you pass over the cutters as shown below.

  4. What Board Should Look Like • This is what the board should look like after you have flattened it. • At this point the board should lie flat on a table.

  5. Step 3 • Now place the face that was just planed up against the jointer fence like shown and joint one of the edges. • Again about 1/16” is about what you want to remove per pass.

  6. Step 4 • Bring board to the table saw • Adjust the fence to take off about 1/8” of material. • Make sure the jointed face is down and the jointed edge is against the fence.

  7. Step 5 • Now I would flip the board over and take another 1/8” from the other side. • Make sure the jointed face is still face down.

  8. Step 6 • Now it is time to plane the other face. • This makes the board the same thickness throughout the piece. • This is what a planer looks like.

  9. More About the Planner • You want to make sure the jointed face is face down. • If you have more than one board do them all the same way to assure a consistent thickness on all boards. • You can’t do this on a jointer because the board will not be the same thickness from end to end.

  10. Another Option • Precision Try squares, combination squares, and framing squares are also good for squaring boards or panels.

  11. Other ways • Plane board • Joint one edge • Table saw second edge (ripping) • Joint second edge to desired width • Cut one end of board square about 1/8” from end • Measure length and cut second end

  12. Presentation Produced by:Marc Nutini • Senior Industrial Technology Education Student • Northern Michigan University • October 28th, 2004