1 / 43

AME 436 Energy and Propulsion

AME 436 Energy and Propulsion. Lecture 10 Unsteady-flow (reciprocating) engines 5: Combustion in engines. Outline. Combustion in engines Knock Misfire / flammability limits Incomplete combustion Pollutant formation. Knock - what is it?.

sook
Télécharger la présentation

AME 436 Energy and Propulsion

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. AME 436Energy and Propulsion Lecture 10 Unsteady-flow (reciprocating) engines 5: Combustion in engines

  2. Outline • Combustion in engines • Knock • Misfire / flammability limits • Incomplete combustion • Pollutant formation AME 436 - Spring 2013 - Lecture 10 - Combustion in Engines

  3. Knock - what is it? • Homogeneous reaction occurring in unburned “end gas” ahead of expanding flame front • Occurs when the combination of piston compression + “flame compression” increases T & P of the end gas until the homogeneous reaction rate is fast enough that a very rapid explosion occurs before the usual turbulent flame front reaches & consumes the end gas - “horse race” between flame propagation and homogeneous reaction in end gas • What does “rapid” mean? Faster than acoustic waves can relax the pressure gradients - prevents even “push” on the piston • How fast is that? Typical engine: Bore = 10 cm = 0.1 m, sound speed = 500 m/s, time scale ≈ 0.1m / 500 m/s = 2 x 10-4 s = 200 µs at most AME 436 - Spring 2013 - Lecture 10 - Combustion in Engines

  4. Knock - movies No knock Knock Videos courtesy Prof. Yuji Ikeda, Kobe University AME 436 - Spring 2013 - Lecture 10 - Combustion in Engines

  5. Knock - why is it bad? • Pressures generated by knock are not substantially higher than those of ordinary (deflagration) combustion but the pressure gradients are huge, causing enormous local stresses on the piston; also causes large torque on piston, thus tilting & rubbing against cylinder wall • As the shocks propagate into the narrow region between the piston and cylinder wall (the “crevice volume”), the shock strength increases, causing locally even more severe damage - usually the crevice volume is where the most knocking damage occurs http://www.llnl.gov/str/Westbrook.html AME 436 - Spring 2013 - Lecture 10 - Combustion in Engines

  6. Knock • Shock formation causes “ringing” of pressure waves back & forth across cylinder - sounds like you're hitting piston with a hammer, which isn't too far from the truth Töpfer et al., SAE Paper 2000-01-0252 (2000) Post-knock ringing Normal combustion (no knocking) Start of knocking AME 436 - Spring 2013 - Lecture 10 - Combustion in Engines

  7. Knock - how do different fuels compare? • Different fuels are compared by means of an octane number • Determine knock-limited compression ratio for your test fuel, using a variable compression ratio engine called a CFR engine (used only for research, not in any vehicle) at specified test conditions (RPM, spark timing, intake T & P, etc.) • Define n-heptane as having octane number = zero, 2-2-4 trimethylpentane = 100 • Blend these two reference fuels to get the same knock limited compression ratio as the fuel under test • The % 2-2-4 trimethylpentane in this blend is the knock rating • Two slightly different sets of test conditions used, called “Research” and “Motor” methods; what's displayed at the gas pump is the average of the two methods (R+M)/2 n-heptane 2, 2, 4 trimethyl pentane (iso-octane) CFR engine AME 436 - Spring 2013 - Lecture 10 - Combustion in Engines

  8. Diesel fuel characterization • For non-premixed-charge engines (i.e. Diesels), you want rapid ignition once the fuel is injected, so fuel requirements are opposite premixed-charge engines • The relevant scale is called the cetanescale, with cetane (16 carbon atoms in a straight line) = 100, heptamethylnonane (9 carbon atoms in a row, with the inner 7 each having a methyl group attached) = 15 (not zero!) n-cetane 2, 2, 4, 4, 6, 8, 8 heptamethylnonane (iso-cetane) AME 436 - Spring 2013 - Lecture 10 - Combustion in Engines

  9. What does octane number measure? • Heating value? Nope - all hydrocarbon fuels have very similar heating values as previous discussed (lecture 2) • Laminar burning velocity (SL)? Nope; SL is practically the same for all stoichiometric hydrocarbon-air mixtures (≈ 40 cm/s) since • As discussed in Lecture 4, SL ~ (w)1/2 • All such mixtures are mostly air, so thermal diffusivity () ≈ same for all • Overall reaction rate (w) is controlled by its value at adiabatic flame temperatures (Tad) • All such mixtures have nearly equal Tad • At these temperatures, controlling reactions are H + O2 OH + O (breaking of O=O double bond, accelerates reaction) H + O2 + M  HO2 + M (competing for H atoms, decelerates reaction) CO + OH  CO2 + H (only way to oxidize CO; regenerates H) and none of these reactions depend on the fuel molecule; fuel decomposition is very fast by comparison at these temperatures • Tendency for mixture to exhibit homogeneous reaction at the typical T & P of end gases (typically 30 atm, 900K)? YES!! • To understand this, need to look at what reactions occur at these T's and P's … AME 436 - Spring 2013 - Lecture 10 - Combustion in Engines

  10. What reactions occur during knock? • Start with fuel molecule RH, where R is an “organic radical”, e.g. propane without an H • Remove an H atom from RH RH + O2 R + HOO • Add an O2 to R R + O2 ROO • Produce peroxides with O-O single bond (half as strong as O=O double bond (120 kcal/mole vs. 60 kcal/mole), much easier to break) ROO + RH  R + ROOH or HOO + RH  R + HOOH • Break O-O single bond, create “chain branching” process ROOH + M RO + OH or HOOH + M HO + OH • Newly created radicals generate more organic radicals RH + OH R + HOH or RH + RO R + ROH • Note that rate of knocking reactions will be sensitive to rates of H atom removal from fuel molecule RH AME 436 - Spring 2013 - Lecture 10 - Combustion in Engines

  11. How does fuel structure affect knock? • Rate of H atom removal depends on strength of C-H bond, which in turn depends on how many other carbons are bonded to that C - stronger bond, slower reaction, less knock • Examples: n-heptane: 6 primary, 12 secondary C-H bonds 2, 2, 4 trimethy pentane: 15 primary, 2 secondary, 1 tertiary AME 436 - Spring 2013 - Lecture 10 - Combustion in Engines

  12. How does fuel structure affect knock? • Does this small difference in bond strength matter? YES because activation energy is high • If we use bond strength as a measure of activation energy (dangerous in general, but ok here…) then at a typical 900K methane : primary : secondary : tertiary exp(-Emethane/T) : exp(-Eprimary/T) : exp(-Esecondary/T) : exp(-Etertiary/T) ≈ exp(-105,000 cal/mole/(1.987 cal/mole-K)(900K)) : exp(-98000/1.987*900) : exp(-95000/1.987*900) : exp(-93000/1.987*900) ≈ 1 : 50 : 268 : 820 • Comparison of fuels • Methane (RON=120, MON=120) - highest of any common fuel • Larger n-alkanes lower, e.g. propane RON=112, MON=97 • Alkenes (C=C double bonds, e.g. ethylene, C2H4) lower • Benzene - very high knock resistance - 113 kcal/mole C-H bond strength - MON=115 • Alcohols good too - methanol: RON=106, MON=92; ethanol RON=106, MON=89 • See chart on page 472 of Heywood AME 436 - Spring 2013 - Lecture 10 - Combustion in Engines

  13. How does fuel structure affect knock? Ghosh et al., Ind. Eng. Chem. Res., Vol. 45, p. 337 (2006) AME 436 - Spring 2013 - Lecture 10 - Combustion in Engines

  14. Anti-knock additives • Any successful additive must inhibit knock reactions without inhibiting flame propagation reactions! • Midgley, Boyd, Kettering (GM research laboratories, Dec. 9, 1921) after trying 1000's of different compounds stumbled onto tetraethyl lead - (C2H5)4Pb • Introduced into gasoline in 1923 - immediately doubled knock-limited compression ratio from 4 to 8, power & efficiency increased (by 40%, from 20.8% to 29.2% according to AirCycles4recips.xls) • Last nail in the coffin for steam and electric vehicles in early 1900's • Mechanism not understood until 1970's - production of fine PbO particle “fog” that acts as a “scavenger” of HOO and HOOH - takes them out of system before they lead to chain branching • … but PbO poisons catalytic converters for exhaust emissions introduced in 1975 - needed to switch to unleaded gasolines (also Pb not exactly environmentally friendly, so not a bad idea to stop using it anyway) - trend was to increase concentration of aromatics (benzene-like molecules) but leads to more soot formation, also carcinogenic AME 436 - Spring 2013 - Lecture 10 - Combustion in Engines

  15. Other anti-knock additives • Methylcyclopentadienyl manganese tricarbonyl (C9H7MnO3, MMT) • Methyl tert-butyl ether (MTBE) (looked good for a while, but now prohibited - water soluble, can be smelled and tasted in water at the parts per billion level • Now: ethanol from corn - very desirable to powerful senators from farm states Ethanol MTBE AME 436 - Spring 2013 - Lecture 10 - Combustion in Engines

  16. How do operating conditions affect knock? • Key points in all this knock stuff • Whether knock occurs is a horse race between flame propagation and homogeneous reaction of the end gas • The chemical reactions that affect flame propagation are different from those that affect knock • Homogeneous reaction rates depend primarily on the initial T & P, whereas flame propagation depends primarily on the final T & P • Thus, operation conditions that affect knock and flame propagation are different!!! • Since knock occurs in end gas, need to see how operating conditions affect end gas T & P AME 436 - Spring 2013 - Lecture 10 - Combustion in Engines

  17. How do operating conditions affect knock? • Simple estimate of maximum T & P of end gas in terms of intake conditions T2, P2 and compression ratio r - assume adiabatic compression, constant-v combustion, reversible adiabatic compression of end gas to (maximum) pressure P4 AME 436 - Spring 2013 - Lecture 10 - Combustion in Engines

  18. How do operating conditions affect knock? • AirCycles4recips.xls end gas calculation • Assumes a small portion of the total mixture has no heat added to it but undergoes reversible compression/expansion according due to the pressure increase/decrease of the rest of the gas in the cylinder that DOES have heat input due to combustion • End gas undergoes heat loss according to the usual formula • The following plot shows effects of compression ratio, spark advance, mixture strength, Tintake and Pintake on the P-T history of end gas AME 436 - Spring 2013 - Lecture 10 - Combustion in Engines

  19. P-T trajectory of end gas (combustion process only) For lean mixture case: f = 0.051, BurnDuration = 0.3, BurnStart = 0.084 (best efficiency timing) Baseline: r = 8,  = 1.3, f = 0.068, QR = 4.5 x 107 J/kg, Tin = 300K, Pin = 1 atm, Pexh = 1 atm BurnStart = 0.045, BurnDuration= 0.105, BurnRateProfile = 0, h = 0.01, Twall = 400K comp = exp = 0.9 AME 436 - Spring 2013 - Lecture 10 - Combustion in Engines

  20. How do operating conditions affect knock? • Compression ratio • As r , Tend gas  and Pend gas , thus knock tendency  • Recall d[fuel]/dt ~ Pnexp(-E/T), (n = order of reaction, E = activation energy) thus both P and T affect knock • P increases more than T, but reaction rate is more sensitive to T than P • Tintake - increasing Tintake increases Tend gas, thus knock tendency  (that's why your car knocks more on a hot day) (though Pend gas isn't affected much by increasing Tintake) • Pintake - increasing Pintake increases Pend gas, thus knock tendency  (that's why your car knocks when you put your foot to the floor) (though Tend gas isn't affected) AME 436 - Spring 2013 - Lecture 10 - Combustion in Engines

  21. How do operating conditions affect knock? • Spark timing • As mentioned in Lecture 9, page 23, as spark timing is advanced, there is more “burn then compress” compared to “compress then burn” which leads to higher T • This also leads to higher P, thus higher Tend gas • Also, igniting earlier means more time for knock to occur • Fundamental tradeoff between increasing spark advance to obtain best thermal efficiency, and decreasing spark advance to minimize knock and NOx • Spark advance up to ≈ 0.05 increases thermal efficiency (see next page), but there's a penalty to pay in terms of knock (Tend gas increasing) and NOx (Tmax increasing) • Tmax and Tend gasdon't increase much as advance increases, but both knock and NOx are high activation energy processes so a little increase in T matters • Note knock and NOx are controlled by very different reactions AME 436 - Spring 2013 - Lecture 10 - Combustion in Engines

  22. Spark advance AME 436 - Spring 2013 - Lecture 10 - Combustion in Engines

  23. How do operating conditions affect knock? • Mixture strength • Many experiments show less knock with leaner mixtures • Leaner mixtures burn slower, so need more spark advance, but even when spark timing adjusted for best efficiency, still less knock that stoichiometric mixtures • Less heat release, thus lower peak P, thus lower Tend gas Ronney, et al., J. Auto. Eng., (Proc. Instit. Mech. Eng., Part D), Vol. 208, pp. 13-24 (1994). AME 436 - Spring 2013 - Lecture 10 - Combustion in Engines

  24. How do operating conditions affect knock? • Engine RPM - generally most important effect is less time for knock to occur - at higher RPM, more turbulence, ST increases, time needed for flame propagation to occur decreases, but turbulence has no effect on time for homogeneous reaction of end gas AME 436 - Spring 2013 - Lecture 10 - Combustion in Engines

  25. HCCI engines • Actually, burning rapidly at minimum volume yields the best possible thermal efficiency, but damage due to knocking means we want to burn “fast but not too fast” • HCCI - Homogeneous Charge Compression Ignition engines take advantages of this - “controlled knocking” Video courtesy Prof. Yuji Ikeda, Kobe University AME 436 - Spring 2013 - Lecture 10 - Combustion in Engines

  26. HCCI engines • By using homogeneous reaction instead of flame propagation, conventional flammability/misfire limits don't exist - recall for homogeneous reaction, burn time is nearly independent of equivalence ratio () • As a result, one can burn very lean mixtures, low Tad, low peak temperature, low NOx formation • Lean mixtures - can obtain part-load operation without throttling and its losses • Since we're asking for knock, use high compression ratios, thus high th • Much more difficult to control the rate and timing of homogeneous reaction than a propagating spark-ignited flame; various control schemes being studied • Variable intake temperature • Variable exhaust gas recirculation • Variable compression ratio and valve timing • Cycle-to-cycle control probably needed • As a result, not in commercial use yet AME 436 - Spring 2013 - Lecture 10 - Combustion in Engines

  27. Comparison of gasoline, diesel & HCCI AME 436 - Spring 2013 - Lecture 10 - Combustion in Engines

  28. Comparison of gasoline, diesel & HCCI J. Dec., Proc. Combust. Instit., Vol. 32, p. 2727 (2009). AME 436 - Spring 2013 - Lecture 10 - Combustion in Engines

  29. HCCI experiments in a single-cylinder engine http://www-cdr.stanford.edu/dynamic/hcci_control/MODELING_talk.pdf AME 436 - Spring 2013 - Lecture 10 - Combustion in Engines

  30. HCCI experiments in 6 cyl. engine (1 cyl. HCCI) http://www.orau.gov/deer/DEER2002/Session9/dec.pdf AME 436 - Spring 2013 - Lecture 10 - Combustion in Engines

  31. HCCI - disadvantages (opportunities?) • Difficult to control timing and rate of combustion • If misfire occurs, gas mixture during the next cycle will be too cold for auto-ignition to occur (unless intake air heating is used), the engine will stop • Cold starting? • Operating window for HCCI operation (load and engine speed) is small - most HCCI concepts use conventional spark-ignited operation at higher loads (less lean mixtures) • Additional components for control system - increased cost • Relatively high friction losses due to low IMEP, thus FMEP is a higher % of BMEP AME 436 - Spring 2013 - Lecture 10 - Combustion in Engines

  32. Misfire / ignition limits • If an engine operates too lean or too rich, the engine will start to run roughly, misfire and may quit altogether • The limit is usually defined by a percentage of misfires (cycles with negative MEP) or a certain percent standard deviation in IMEP • With conventional spark ignition premixed-charge engines, the limit is at equivalence ratio () ≈ 0.65 - 0.75, whereas in a laboratory experiment (e.g. on a bunsen burner) ≈ 0.5 will burn • Why the difference? In the laboratory, the mixture can take as long as it wants to burn, whereas in the engine, there is only a limited time ~ 1/N available for burning - minimum turbulent burning velocity (ST) requirement • To avoid misfire • Increase burning velocity • Increase time available for burning • Decrease time needed for burning AME 436 - Spring 2013 - Lecture 10 - Combustion in Engines

  33. Misfire effects of operating conditions • Inlet temperature • As T∞ with  fixed, Tad, SL , thus ST  (slightly) • Since SL depends more on Tad than any other property, limit criterion is basically a minimum Tad criterion • Recall Tad = T∞ + fQR/Cv - can get a given Tad with a high f (thus high ) and low T∞ or vice versa • “Brilliant” experiments show this - limit Tad 2000K - 2100K Ronney, et al., J. Auto. Eng., (Proc. Instit. Mech. Eng., Part D), Vol. 208, pp. 13-24 (1994). AME 436 - Spring 2013 - Lecture 10 - Combustion in Engines

  34. Misfire - effects of operating conditions • Intake pressure • Recall SL ~ P(n-2)/2, with n typically slightly less than 2, not much effect • But as Pintake decreases, more exhaust gas (at 1 atm) relative to fresh mixture (at P < 1 atm), so more dilution of mixture with exhaust gas, thus lower Tad, lower SL • Thus more problems with misfire at throttled conditions (for fixed N) • Turbulence - more turbulence, higher ST - helps limit problem, but remember too much turbulence will extinguish the flame! • Engine RPM (N) • Time available for burning ~ 1/N • But u'~ upiston ~ N and ST ~ u' • So (time available for burning)/(time needed) ≈ constant • But actually ST ~ u'(1-), so you have more problems with misfire at higher N AME 436 - Spring 2013 - Lecture 10 - Combustion in Engines

  35. Misfire - effects of operating conditions • Multiple spark plugs - reduces distance each evolving flame needs to propagate, less chance of misfire, so less misfire problem • Knock additives (e.g. (C2H5)4Pb) - no effect (affects knock reactions, not flame propagation reactions) AME 436 - Spring 2013 - Lecture 10 - Combustion in Engines

  36. Lean mixtures - effect on temperatures • Frequently I hear the comment from non-thermodynamicists who know engines that “engine temperature increases as you go leaner - if you go too lean you'llburn up the engine” • Thermodynamically this makes no sense - leaner mixtures have lower Tad = T∞ + fQR/Cv (constant volume) • BUT - leaner mixtures burn slower - more heat release after some expansion already completed - less expansion, higher T • Since chemical reactions have high activation energy, a small decrease in Tad (leaner mixture) causes a large decrease in SL, thus much slower burn, higher exhaust T AME 436 - Spring 2013 - Lecture 10 - Combustion in Engines

  37. Lean mixtures - effect on temperatures • Slow-burn effect > lower-Tad effect r = 3,  = 1.3, f = 0.068 or 0.0612, QR = 4.5 x 107 J/kg, Tin = 300K, Pin = 1 atm, Pexh = 1 atm, BurnStart = 0.0841, BurnDuration = 0.15, 0.3 or 0.45, ExhRes = FALSE, Const-v comb, ComplExp = FALSE, h = 0.01, Twall = 400K, comp = exp = 0.9 AME 436 - Spring 2013 - Lecture 10 - Combustion in Engines

  38. Lean mixtures - effect on temperatures AME 436 - Spring 2013 - Lecture 10 - Combustion in Engines

  39. Lean mixtures - effect on temperatures After expansion After blowdown Const. v After exhaust stroke Const. P AME 436 - Spring 2013 - Lecture 10 - Combustion in Engines

  40. Incomplete combustion (review from Lecture 4) • Most fuel is burned in engines - very little unburned fuel under normal operating conditions unless mixture is too lean, too rich or otherwise “disabled” • Flame quenching may occur in the “crevice volumes” where gap < quenching distance - main source of hydrocarbon emissions from engines • Before we get to the point that raw fuel is emitted, some fuel reacts only partially - sequence of events: Fuel + O2 CO + H2 CO + H2 CO + H2O CO + H2O  CO2 + H2O so CO emissions are the first sign of trouble! AME 436 - Spring 2013 - Lecture 10 - Combustion in Engines

  41. Example #1 For the Otto cycle example in Lecture 9 with r = 9,  = 1.3, M = 0.029 kg/mole, f = 0.062, QR = 4.3 x 107 J/kg, T2 = 300K, P2 = Pin = 0.5 atm, P6 = Pex = 1 atm, h = 0, comp = exp = 0.9, determine the end gas temperature and pressure If this were an ideal cycle we could use the formula on page 16, i.e. But since this is not an ideal cycle we compress the end gas isentropically from its pressure (9.165 atm) and temperature (611K) after compression to the pressure after combustion (51.02 atm) , i.e. which is not much different. AME 436 - Spring 2013 - Lecture 10 - Combustion in Engines

  42. Example #2 During WWII, fighter aircraft engines were equipped with systems to inject water into the cylinders during compression. How would water injection affect • Knock tendency: The water would cool the intake charge and increase its , thus reducing the end-gas temperature substantially. Also, while the compression ratio could not be changed, the intake pressure could be increased (these were turbocharged engines) without knocking, thus allowing more air to be ingested • Misfire tendency: The greater mass of un-burnable water vapor and its higher Cp (compared to air) led to lower Tad, thus more tendency to misfire. This limited the amount of water that could be injected. • Power: This was the main reason for water injection. The liquid water requires much less Work/mass to compress than air (Work = ∫PdV thus Work/m = ∫Pd(V/m) = ∫Pd(1/ρ), and ρwater >> ρair), yet when the liquid water vaporizes, its volume increases tremendously, generating more expansion work / compression work (this is why steam cycles are more efficient that gas cycles!) Also as mentioned above, the intake air pressure could be increased, thus allowing more fuel to be added and burned • Brake thermal efficiency: The slower burning would decrease efficiency, but the steam cycle has inherently higher efficiency, so it could go either way. • Work per unit mass of (fuel + water): This would definitely decrease, since the water provided no additional heat release but much additional mass. In actuality, these aircraft used a methanol/water mixture, not just water, to recover some energy release from the injected liquid (though note methanol has only 40% of QR of gasoline) AME 436 - Spring 2013 - Lecture 10 - Combustion in Engines

  43. Summary • Knock • A very rapid homogeneous reaction in the “end gas” ahead of the flame front • Horse race between knock (bad) and flame propagation (good) • Knock tendency depends on reaction rates at initial T, P & composition of reactants (end gas), flame propagation depends on final (burned gas) temperature, so factors affecting knock & flame propagation are very different • Knock tendency characterized by octane number - higher ON, more resistant to homogeneous reaction • Diesel fuels - opposite characteristics desired • Misfire / flammability limits • Due to insufficient ignition source or time to burn - roughly corresponds to fixed Tad • Depends on required propagation time (~ d/ST) vs. available time (~1/N) • Incomplete combustion • Due to insufficient time to burn - CO is first sign of trouble AME 436 - Spring 2013 - Lecture 10 - Combustion in Engines

More Related