1 / 15

Comparative Study: EN 13445 – ASME VIII

Comparative Study: EN 13445 – ASME VIII. Workshop on the Pressure Equipment Directive Warsaw, June, 2004 Dr. Reinhard Preiss TÜV Austria Krugerstrasse 16 A-1015 Vienna, Austria Tel. +43 1 51407 6136 e-mail: prr@tuev.or.at http://www.tuev.at. Introduction.

thomaswatson
Télécharger la présentation

Comparative Study: EN 13445 – ASME VIII

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Comparative Study: EN 13445 – ASME VIII Workshop on the Pressure Equipment Directive Warsaw, June, 2004 Dr. Reinhard Preiss TÜV Austria Krugerstrasse 16 A-1015 Vienna, Austria Tel. +43 1 51407 6136 e-mail: prr@tuev.or.at http://www.tuev.at

  2. Introduction • This study compares the economic and non-economic implications arising from the application of (a) EN 13445 and, (b) the internationally used ASME Boiler & Pressure Vessel Code plus major related codes when appropriate (TEMA, WRC Bulletins), for the design, manufacture, inspection and acceptance testing of 9 benchmark examples of unfired pressure vessels.

  3. Introduction • The consortium which carried out the study, based on a contact with the EC / DG Enterprise, consists of TUV Austria - a Notified Body acc. to the PED in Austria -, and of Consorzio Europeo di Certificazione (CEC) - a Notified Body acc. to the PED in Italy. • The detailed design of the benchmark examples was performed by the consortium. To evaluate the economic factors concerning individual and/or serial production of the benchmark vessels, pressure equipment manufacturers from Italy, France, Germany and Austria took part as subcontractors.

  4. Benchmark Examples - Overview

  5. Benchmark Examples - Overview

  6. Benchmark Examples - Overview

  7. Benchmark Examples – CNG Storage Tank

  8. Benchmark Examples – Stirring Vessel

  9. Benchmark Examples - Aircooler

  10. Conformity Assessment For estimation of the costs the following combinations of codes and conformity assessment routes were considered: • EN 13445 and conformity assessment according to the PED (CE-marking).· • ASME Section VIII (Division 1, Division 2 if applied) and conformity assessment according to ASME (U-stamp, or U2-stamp). • ASME Section VIII (Division 1, Division 2 if applied) and conformity assessment according to the PED (CE-marking).

  11. Conformity Assessment • The exercise is based on compliance with the corresponding requirements in a situation where there are no pre-existing qualifications or supplementary data which could be used from other similar equipment. • In the case of application ASME Section VIII (Division 1, Division 2 if applied) and conformity assessment according to the PED additional requirements were made (these are based on an agreement between the members of the consortium on the general approach within their organisations to such matters, but they cannot be taken as generally valid for PED conformity assessment for vessels designed according to the ASME code) for • Materials • Hydrostatic test Pressure • Permanent joining and NDT • Fatigue design

  12. Overall Summary

  13. Overall Summary • Material costs are frequently greater using the ASME code. In some cases, savings attributable to lower material costs with EN 13445 are partly offset by additional costs of weld testing and NDT when compared with ASME requirements. • For standard refinery heat exchangers no notable costs differences are reported (if TEMA requirements are considered). • In some cases the reported costs differences for different manufacturers are larger than the cost differences resulting from the application of the various code routes. • PWHT costs are frequently higher for ASME design, since the PWHT requirements depend on the wall thicknesses.

  14. Overall Summary • Material costs using EN 13445 Design-by-Analysis techniques are lower in some cases (e.g. special and/or advanced design or materials), but design costs are higher as for DBF since a finite-element-analysis is required. • According to the cost estimations of the manufacturers, the extra costs for ASME designs to meet the PED requirements are in general small for the approach used in the study.

  15. Overall Summary • Based upon the design results, fatigue design according to ASME Div. VIII Sec. 2 Appendix 5 for welded regions is considered to be non-conservative in comparison with fatigue analysis procedures in major European pressure vessel codes (e.g. EN 13445, AD-Merkblatt, PD 5500) and the underlying experimental results. Thus, ASME fatigue design for these regions is not considered to meet the requirements of PED Annex I. Concerning the necessity for improvement of the present ASME fatigue rules see the current proposal for revision of ASME VIII Div. 2.

More Related