1. Intelligent Control Panel SLC

2. Branch Line Resistor from End of Line to FACP Shall Not Over 50 ohms per Branch M M M M M M M M M FACP NFPA Style 4 SLC Twisted Unshielded Pair 12 to 18 AWG SLC Distance 12 AWG 3180 M 16 AWG 1486 M 14 AWG 2438 M 18 AWG 986 M

3. M M M M M M M M M FACP Style 4 with Isolators

4. M M M M M M M M M NFPA Style 6 SLC Loop Resistor from End of Line to FACP Shall Not Over 50 ohms

5. M M M M M M M M M Style 6 with Isolators • SLC address capacity of loop is reduced by 2 addresses for every isolator device in excess of 200.

6. SLC address capacity of loop is reduced by 2 addresses for every isolator device in excess of 200. ISO ISO ISO ISO M ISO ISO C ISO ISO M ISO ISO ISO ISO ISO ISO Style 7

7. SLC Performance

8. (+) SLC Channel A no connection (-) SLC Channel A NFS-640 Floating Shield

9. SLC Data Formats FlashScan is an algorithm that greatly enhances the speed of communication between the Analog intelligent devices. If one of the devices within a single group has new information, The panel CPU stops the group poll and concentrates on single points. The net effect is a response speed greater than five times that of earlier designs.

12. LED Operation

13. 9 0 8 7 9 6 10 5 11 8 4 1 12 3 13 2 7 1 14 2 0 15 TENS 8 7 9 6 5 6 3 4 3 2 5 4 1 0 ONES ADDRESS LOOP FlashScan Modules Break-off address stop for panels with FlashScan Mode.

14. FZM-1 接點3、4需接可復歸( Resettable) DC 24電源接線採用Class B時，終端電阻為3.9KΩ

15. FZM-1 接線採用Class A時，終端電阻為3.9KΩ

16. FMM-1 接線採用Class B時，終端電阻為47 KΩ、1/2W

17. FMM-1 接線採用Class A 時，無需終端電阻

18. FMM-101 終端電阻為47 KΩ、1/2W

19. FCM-1 輸出接線採用Class B時 接點6、7之終端電阻為47KΩ、1/2W

20. FCM-1 採用Class A 時，無需終端電阻

21. FRM-1 外接負載應小於模組之接點容量 接 點 容 量 電阻性元件 30VDC @ 2A 電感性元件 30VDC @ 1A交流元件 125VAC @ 0.5A

22. 1 2 3 4 Devices - Modules • Isolator Module (ISO-X) • Supervises loop wiring for short circuit conditions • Allows critical component functions • Required for Style 7 operation • Supported by FlashScan and CLIP systems

23. 9 0 8 1 7 2 8 7 9 6 8 10 6 5 6 3 11 4 4 12 3 2 5 13 4 2 0 1 14 ONES 0 15 TENS ADDRESS LOOP FDM-1 Wiring Class B The circuit connected to terminals 6 & 7 are assigned the base address. The circuit connected to terminals 8 & 9 are assigned the base address plus 1. RED LED lights for either circuit 1 or circuit 2 alarm.

24. Control Module FCM-1 Class A or B NAC, Speaker or Telephone 2A @ 30VDC 43.75W @ 25 Vrms 43.75W @ 70.7 Vrms 40 Ohm telephone riser Relay Module FRM-1 Dual Form-C operation (DPDT) 8 7 9 6 10 5 11 4 12 3 13 2 1 14 0 15 TENS 8 7 9 6 5 4 3 2 1 0 ONES 9 0 8 1 7 2 6 3 5 4 ADDRESS LOOP FCM-1 Control Modules

25. FRM-1 Contact Rating

26. 1 2 3 4 Devices - Modules • Isolator Module (ISO-X) • Supervises loop wiring for short circuit conditions • Allows critical component functions • Required for Style 7 operation • Supported by FlashScan and CLIP systems

27. Wiring the B224BI Isolator Base Twisted Pair Recommended Listed FACP Isolator bases prevent an entire communication loop from being disabled when a short circuit occurs, by isolating that part from the remainder of the circuits. OTHER INTELLIGENT DEVICES

28. Wiring the B710HD Base AUX POWER SUPPLY SLC

29. Wiring an NBG-12LX Pull Station + SLC - + SLC -

30. Building 2 Building 1 P P P = Primary S= Secondary S P S P Wiring Surge Suppressor

31. Any Questions?