HF Mobile Installation and Operation

1. HF Mobile Installation and Operation

2. Why HF Mobile? • HF Bands are used for Long and Medium haul communications. VHF & UHF for short range or local communications.

3. Why HF Mobile? • With today’s modern compact transceivers it is possible to have portable HF communication in our vehicles.

4. Components Of A Mobile Station • Transceiver • Antenna System (radiator + matching network) • Power Source

5. Transceivers There are many HF transceivers on the market made specifically for mobile or portable use.

6. Transceivers • Units designed for mobile work usually have easy to read displays. • They should be mounted so that they do not affect the driver’s ability to safely operate the vehicle.

7. Yaesu offers many models for mobile operating

8. ICOM has its IC-706 and IC-703 (QRP) models

9. Kenwood’s TS-480 is available in a 200 watt version

10. Alinco DX-70 THHF+6m All Modes

11. Antenna Systems • Mobile antenna Systems are comprised of a radiator and a matching network. • Mobile antennas have a low impedance, therefore, a matching network is required.

12. Antenna Systems • Systems can be mono-band or multi-band. • Multi band systems can be tuned from inside the vehicle while in motion or from outside the vehicle when stopped.

13. Antenna Systems:Good, Bad and Ugly • All systems have some sort of loading. • Center loading is best. • Base loading is least effective • Because of their skinny coils, helically wound antennas are a compromise of the other two designs.

14. SWR • A good SWR is not an indicator of an effective antenna system. • Click your heels and say this three times. • Think of a dummy load; it has a good SWR but is not an effective antenna.

15. BIG NOTE * *An entire program can be had just on the discussion of antennas. All mobile antennas are a compromise of some sort and much consideration should be given to safety and the type of operating that is being done, as well as spouse appeal. End of Big Note.

16. Multi Band Antennas • Motorized • Automatically tuned • Manually tuned

17. Center Loaded Antennas Whether motorized or manually tuned, these are by far the most effective type of mobile antenna.

18. Motorized Antennas • Commonly called “screwdriver” antennas because the first designs used cordless screwdriver to drive the screw that adjust the coil. • Uses a motor to move a large coil up and down to obtain resonance. • System consist of the large coil, whip radiator, shunt coil at feed point and a control unit

19. Motorized AntennasAdvantages • Multi band. • Can be tuned from inside the vehicle. • Hi “Q” Very effective antenna. • Computerized control units can be added for quick band changes.

20. Motorized AntennasDisadvantages • Large and heavy; requires strong mounting and support brackets. • Hi “Q” make tuning on low bands very touchy.

21. High Sierra motorized antennas

22. Lil Tar heel motorized antenna

23. The Yaesu ATAS-100 Active Tuning Antenna System provides HF/VHF/UHF coverage with automatic motorized tuning. Utilizing control signals from the transceivers microprocessor received via the coaxial cable, the ATAS-100's internal motor adjusts the radiator length for best SWR.

24. Manually Tuned Center LoadedMulti Band Antennas • Some types use taps to tap the coil at a resonant point. • Other designs use multiple resonators or change resonators on a single mast.

25. Bug CatchersAdvantages • Very effective center loaded antennas. • Large coils results in Hi “Q”. • Can be tapped to use on multiple bands

26. Bug CatchersDisadvantages • Large and heavy requires strong mounting and support. • Band changes have to done while parked.

27. Large coil and center loading make the Bugcatcher an excellent performer. This unit is shown with a capacitance hat.

28. Capacitance Hats • Loss resistance is lowered by removing turns in an inductor coil. • This is then compensated for by adding capacitance above the coil. • The more capacitance that is added the less inductance is needed for a given frequency.

29. CPU Controlled Automatically Tuned Multi Band Antennas • Uses a CPU controlled matching network and a whip antenna. • Can match almost any frequency. • Some models are capable of matching over a million LC combinations in less than a second.

30. CPU Controlled Automatically Tuned Multi Band Antennas • System can be made low profile. • Internal memories save settings an allow quick band changes.

31. CPU Controlled Automatically Tuned Multi Band Antennas • When used with a loaded whip designed for the tuner these systems can be extremely effective. • When used with a 8 ft. whip the system is less effective than loaded whip or center loaded systems.

32. Interior view of YAESU FC-40 CPU controlled remote tuner for FT-897 & FT-857 radios

33. ICOM AH-4 CPU controlled auto-tuner for use with many ICOM radios

34. ALINCO EDX-2for USE exclusively with ALINCO DX-70T, DX-70TH, DX-77EQ, DX--77T, DX-701 and DX-707

35. SGC makes an entire line of reliable CPU controlled auto-tuners that will match almost any radiator with any radio.

36. SGC’s QMS system is rugged, mounts on any vehicle and includes the CPU tuner and loaded whip antenna.

37. Mono-Band Antennas • Operate on a single band. • Can be effective. • Can be made low profile. • Can be easily mounted. • Inexpensive way to enter into HF mobile.

38. Good results can be had with mono band antennas. These “sticks” can be easily mounted and are lower profile.

39. Antenna Mounting • Which ever antenna is used the mount has to be solid, strong and safe. • No sharp edges or protrusions that could cause injury. • Anything flying off a moving vehicle can be deadly. Safety first. • Obey DOT laws.

40. Custom Heavy Duty Mount

41. Notice the heavy braided ground strap added to this custom mount ensuring a good bond to frame.

42. Custom Heavy Duty Mount

43. Don’t Be Afraid To Drill A Hole

44. Mounting Alternatives

45. Mounting Alternatives

46. Grounding • A good solid ground connection to the vehicle frame is necessary for good antenna performance. • Make ground connections as short as possible and to bare metal. • Ground connections can be weatherproofed with undercoating spray.

47. Bonding • Bonding is connecting together loose or moving metal parts of the vehicle with grounding braid. • These areas are doors, trunk and hood lids, mufflers and exhaust parts, and any other areas where metal parts may rub. • Rubbing metal parts can cause excessive noise in the receiver.

48. Power • Power should be taken directly from the vehicle’s battery. • Both positive and negative leads should be fused at the battery. If there is a fault anywhere after the fuse the fuse will do it’s job and break the circuit.

49. Both leads should be fused at the battery to prevent fire.

50. Power • Drawing power directly from the battery helps eliminate noise. • All leads should be 10 ga. or larger stranded wire and be kept as short as necessary. • Protect wires with rubber grommets where they pass through the firewall or any metal.