Download
1 / 107
1.35k likes | 2.52k Vues
The Evolution of the Spinal Needles. Joseph Eldor, MD. An Inguinal Hernia operation in 1382…Without Spinal needles.
E N D
The Evolution of the Spinal Needles Joseph Eldor, MD
Valsalva, in 1682, was the first to remark on the CSF when he cut open the spine of a dog and noticed the liquid "which in all its aspects resembles that which is found in the joints".
In 1764, Cotugno described the presence of a collection of water around the brain and inside the spinal column.
In 1825, Magendie was credited with appreciating that this fluid circulated around the brain and the spinal column.
By 1841, Zophar Jayne of Illinois had designed a syringe attached to a small, sharp, hollow beak with an opening on the side near the tip.
Subsequently, in 1853, Daniel Ferguson developed a syringe and hollow platinum trochar with an oblique opening on one side encased in an outer tubing, also with an oblique opening. Ferguson is credited by some as being the first to use a hollow needle with a sharpened extremity, allowing skin penetration and attachment to a syringe.
Alexander Wood of Edinburgh is credited with developing the first hollow hypodermic needle in 1853.
The birthdate of regional anesthesia was September 15, 1884, the date on which Carl Koller , an intern at the Allgemeines Krankenhaus in Vienna, conclusively demonstrated the topical anesthetic properties of cocaine applied to the conjunctiva of the eye.
The first application of the principle of nerve blocking for surgical anesthesia was carried out early in November 1884, when Halsted removed a supraorbital lipoma following cocainization of the supraorbital nerve at the supraorbital notch.
The first spinal anesthetic was administered accidentally by J. Leonard Corning, a Neurologist from New York in 1885.
Corning was experimenting with the action of cocaine on the spinal nerves of a dog when he accidentally breached the dura between two lumbar vertebra, causing paralysis of the hindquarters, and hence inadvertently performed the first spinal anesthesia.
Corning developed his own spinal needle and introducer. The needle was made of gold or platina. The needle tip was based on the hypodermic needle developed by Wood in 1853. It was sharp,with a short cutting bevel.
In 1891, Quincke published a paper describing a standardised technique of lumbar puncture for the release of CSF for diseases associated with increased intracranial pressure. He used a needle of which it is difficult to find a description, except that it was a sharp, bevelled, hollow needle.
August Bier, on August 24, 1898, asked his assistant, Dr. Hilderbrandt, "to perform a lumbar puncture on me", 8 days after he first performed it on a 34-year-old patient for excision of a tuberculous capsule at the ankle joint. Bier wrote that he did not feel any discomfort "except for a quick flash of pain in one leg at the moment that the needle penetrated the meninges". Unfortunately, the experiment was not successful because of an error (the syringe did not fit the needle tightly... and consequently some CSF ran out and most of the cocaine was lost). No sensory loss ensued.
Dr. Hilderbrandt immediately offered to submit himself to the experiment, which was successful.
Both of them "went to eat after the experiments were performed on our bodies. We had no physical discomfort, we ate, drank wine, and smoked several cigars". However, next morning, after a one hour morning stroll Bier felt slight headache which increased in intensity during the course of the day. Nine days after the puncture, all the symptoms disappeared. After 3 more days, "I was able to go on a train trip without discomfort and was fit enough to participate in a strenuous 8 day hunting trip in the mountains".
In 1899, Bier published six case reports of surgery to the lower limbs under spinal anesthesia with cocaine. The needle used was described as a Quincke needle.
Bier also designed a larger bore needle that needed no introducer. The Bier spinal needle was 15G or 17G, with a long, cutting bevel and a sharp point.
Bainbridge described a needle in 1900 that was attached to a metal syringe. It had a small circular hub, a short, sharp cutting bevel and a stylet with a matching bevel.
Barker designed in 1907 a needle which had a sharp, medium-length bevel and a stylet with a matching bevel. Barker advised that needles be made of hard nickel.
As early as 1898 Sicard realised that the cause of PDPH (Post Dural Puncture Headache) was the loss of CSF through the dural tears.
In 1914, Ravaut advised the use of finer needles to limit the size of the dural tear.
In 1914, Babcock described a needle that was closer in design to the original Corning needle but with a finer cannula to limit the incidence of PDPH. It had a sharp, medium-length bevel with a matching stylet. It was made of iridised platinum or gold and was 20G in diameter. Referred to as the Quincke-Babcock needle.
Gaston Labat designed a spinal needle that was made of unbreakable nickel. It was a medium-gauge cannula with a short, sharp bevel and matching stylet, with the tip ground to match the bevel of the cannula.
In 1922, Hoyt published his theory that the large bore needles were, because of their rigidity, resulting in large holes in the dura and an increased loss of CSF. He proposed the use of a two-needle technique with a larger bore outer needle being used for penetration of the outer tissues and a finer inner needle for penetration of the dura and arachnoid.
In the 1920s, heat-tempered stainless steel was developed in England. Towards the end of World War I, Germany was manufacturing a hard steel alloy that was rustproof, very resistant to breaking and could be worked to a sharp point that was resistant to deformation. The rustproof products became the mainstay of needle production.
The Greene needle was sized between 20G and 26G. The point was a rounded, non-cutting bevel of medium length with a matching, bevelled, fitted stylet.
There is some disagreement as to the actual date of the introduction of the Greene needle: Herbert Morton Greene presented his work in 1923 and 1926. However, the design should perhaps be attributed to Barnett A Greene who, in 1950, published on the use of a 26G needle passed through a 21g introducer.
George Praha Pitkin devised in 1927 a 20G or 22G needle made of relatively flexible rustproof steel with a collar to mark the depth of insertion. The tip of the needle had a short, sharp bevel ground off to a taper of 45º, resulting in a rounded, blunted bevel heel.
Kirschner,in 1931, described a needle for spinal anesthesia with an opening in the shaft just proximal to the beveled closed end. He claimed that the lateral orifice allowed unilateral, cephalad or caudal anesthesia to be administered.
Rovenstine took up the design idea of the closed-end needle and in 1944 published a paper describing his spinal needle. Rovenstine’s needle was 19G or 20G. It had a closed, short-bevelled point with a lateral orifice 2 mm from the distal end of the needle.
