1 / 9

Tritium Permeation Issue, Plan and Progress

Tritium Permeation Issue, Plan and Progress. ITER. Dai-Kai Sze. University of California, San Diego Presented at the ITER TBM Project Meeting UCLA, Feb. 23-25, 2004. Statement of Problem. ITER. Fusion blankets have high tritium partial pressure.

adelio
Télécharger la présentation

Tritium Permeation Issue, Plan and Progress

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Tritium Permeation Issue, Plan and Progress ITER Dai-Kai Sze University of California, San Diego Presented at the ITER TBM Project Meeting UCLA, Feb. 23-25, 2004

  2. Statement of Problem ITER • Fusion blankets have high tritium partial pressure. • The temperature of the blanket is high. • The surface area of the heat exchanger is large, with thin wall. • Those are the perfect conditions for tritium permeation. • The allowable tritium loss rate is very low.

  3. Typical tritium partial pressure ITER For LiPb 0.014 Paa For flibe 380 Paa For Li 2.6X10-8 Pab For solid breeder 0.6 Pac • The tritium partial pressure increase per coolant path. • Assuming tritium concentration of 1 ppm . • With a purge gas flow rate of 104 liter/s.

  4. Tritium Permeation ITER Typical parameters of heat exchangers are: Temperature 500C Surface area 2.5X104 m2 Wall thickness 1 mm Tritium permeability in FS = 0.46 mol T2-mm/d-m2-atm0.5 If the tritium partial pressure is 1 Pa, the tritium permeation rate will be 218 g

  5. ITER Methods to reduce Tritium Permeation • Develop efficient tritium recovery system from the breeding material. • Develop high performance tritium diffusion barrier. • Convert tritium from elementary form to oxide form. • Secondary tritium clean up from the intermediate coolant. • Tritium clean up from the power conversion medium.

  6. Canada Experience ITER • CANDU loss about 10 Kg/hr coolant water, and 2-5 Kg/hr of moderator water • About 95% of the water is recovered. • About 50% of the tritium emission is from the water loss. • Only about 5-10% of the emission is caused by tritium permeation.

  7. Tritium loss from fusion ITER • Permeation is a much important path for tritium loss for fusion than for CANDU, because tritium is in elementary form. • Tritium loss caused by coolant loss, either water or He, has to be included. • CANDU losses about 200 Ci/d, and it has a much smaller tritium throughput than fusion. • Is it reasonable to expect fusion can achieve a loss rate close to 1 Ci/D?

  8. Where are we? ITER • Tritium recovery processes from breeder materials are in good shape. • Tritium diffusion barrier development did not obtain the required performance. • Tritium oxidation kinetics has been studied, but results vary. • Some efforts, mainly for safety concerns, have been spent to develop an intermediate heat exchanger.

  9. Where are we? (Cont.) ITER • The leakage of the coolant, especially water and He, needs to be carefully assessed. • The economy of the tritium clean up system depends strongly on the coolant leakage rate. • Loss coolant recovery rate, was 95% of the CANDU system, will have major impact on the tritium loss rate. • SR tritium loss rate is about 4 g/y (100Ci/d), while the CANDU reactor loss about 200 Ci/d, is it reasonable to limit the tritium loss rate to a fusion power plant to between 1 to 30 Ci/D? • It will be useful for us to get back the last VG for further discussion.

More Related