1 / 16

Magnetic Measurements At SLAC

Magnetic Measurements At SLAC. Zack Wolf, Scott Anderson, Ralph Colon, Brendan Dix, Scott Jansson, Dave Jensen, Luis Juarez, Seva Kaplounenko, Yurii Levashov, Wei Wang, Achim Weidemann. Magnetic Measurements Outlook. PEP II, ceases operation by 2009, magnetic measurements nearly complete

alandis
Télécharger la présentation

Magnetic Measurements At SLAC

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Magnetic Measurements At SLAC Zack Wolf, Scott Anderson, Ralph Colon, Brendan Dix, Scott Jansson, Dave Jensen, Luis Juarez, Seva Kaplounenko, Yurii Levashov, Wei Wang, Achim Weidemann

  2. Magnetic Measurements Outlook • PEP II, ceases operation by 2009, magnetic measurements nearly complete • SPEAR III, running, magnetic measurements nearly complete • ILC, SLAC proposed warm design, not chosen, now what???, getting superconducting magnet to study center shifts during BBA • LCLS, SLAC’s next big project, many undulators to measure, many conventional magnets also

  3. New Undulator Measurement Lab • Floor plan divided into three functional areas • Magnetic Measurements (± 0.1º C) • Fiducialization and Assembly (± 1º C) • Storage (± 2.5º C) • Test stand lay-out is driven by requirement to match the Earth Magnetic Field conditions in lab to Undulator Hall, i.e. azimuth and gap orientation need to be identical

  4. LCLS Undulator (At ANL) Probe Air Bearing Undulator Belt Drive Cam Mover Bench

  5. Purchasing Measurement Bench (Similar to ANL bench Shown) X, Y Stage Hall Probe Carriage On Air Bearings Undulator Granite Bench Steel Belt Linear Scale

  6. Undulator Bench Construction Requirements

  7. Initial Placement Of Undulator • Probes at nominal height • Cam movers move undulator to probes

  8. By By By y x Place Undulator (cont.) Capacitive Sensors, Mechanical Alignment Magnetic Alignment

  9. Probe Construction (and Hall probe) Preamp (very low offset drift) Use SENIS Hall probe. Hall Probe (need 10-4 acc → good calibration System) Coil (6000 turns 1 mil wire, 4x6x12 mm, 0.2 m2)

  10. Hall Probe Calibration System Under construction Flowing water NMR: 1 probe Small chiller for probe temperature

  11. Undulator Field Integrals Long Coil 150 Turns I1 I2

  12. Undulator Fiducialization Magnets Need to relate magnetic field to tooling balls. Attach to undulator ends, measure offsets See Yurii Levashov’s talk

  13. Temperature Measurements Desired Measurement Accuracy 0.01 C

  14. Quadrupole Fiducialization

  15. Quadrupole Strength And Harmonics Use Rotating Coil Systems Examples Of Rotating Coil Systems

  16. Conclusion Our next big magnetic measurement project is the LCLS. A new magnetic measurements lab is being built. We will use Hall probes and coils to tune the undulators. Long coils will check the first and second field integrals. High gradient magnets with well defined centers will be used to fiducialize the undulators. The quadrupoles will be measured for strength and harmonics with a rotating coil. The quadrupoles will be fiducialized using the vibrating wire technique.

More Related