1 / 89

Chapter 11

Chapter 11. Logic Gate Circuitry. Basic Logic Families. TTL – transistor-transistor logic based on bipolar transistors. CMOS – complementary metal-oxide semiconductor logic based on metal-oxide-semiconductor field effect transistors (MOSFETs).

alaura
Télécharger la présentation

Chapter 11

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Chapter 11 Logic Gate Circuitry

  2. Basic Logic Families • TTL – transistor-transistor logic based on bipolar transistors. • CMOS – complementary metal-oxide semiconductor logic based on metal-oxide-semiconductor field effect transistors (MOSFETs). • ECL – emitter coupled logic based on bipolar transistors.

  3. General Characteristics of Basic Logic Families • CMOS consumes very little power, has excellent noise immunity, and is used with a wide range of voltages. • TTL can drive more current and uses more power than CMOS. • ECL is fast, with poor noise immunity and high power consumption.

  4. Logic Subfamilies • Both TTL and CMOS are available in a wide range of subfamilies. • In subfamilies, the part designations for identical logic functions remain the same, but the electrical characteristics are different.

  5. Examples of TTL Subfamilies

  6. Examples of CMOS Subfamilies

  7. Input/Output Voltage and Current Definitions • Values for any gate are designated with two subscripts: • The first subscript indicates an input or output value • The second subscript indicates the logic level

  8. Input/Output Voltage Designations • VOL – the logic LOW output voltage. • VOH – the logic HIGH output voltage. • VIL – the logic LOW input voltage. • VIH – the logic HIGH input voltage.

  9. Input/Output Voltage Designations

  10. Input/Output Current Designations • IOL – the logic LOW output current. • IOH – the logic HIGH output current. • IIL – the logic LOW input current. • IIH – the logic HIGH input current.

  11. Input/Output Current Designations

  12. Part Designation • Typically 54XXYY or 74XXYY. • 54 series is manufactured to military specifications. • 74 series is manufactured to commercial specifications. • XX is the subfamily designation. • YY is the part designation.

  13. Data Sheets • Use the appropriate maximum or minimum parameters in design. • Typical values should be considered “information only.” • Refer to Figure 11.3 in the textbook.

  14. Propagation Delay • The time required for the output of a digital circuit to change states after a change at one or more of its inputs. • Largely due to charging and discharging of capacitances inherent in the gate or flip-flop switching transistors.

  15. Propagation Delay Definitions • tpHL is the propagation delay when the device output changes from HIGH to LOW. • tpLH is the propagation delay when the device output changes from LOW to HIGH.

  16. Propagation Delay Definitions

  17. Propagation Delay Definitions

  18. Propagation Delay Factors • Varies with operating conditions. • Particularly affected by temperature and the power supply voltage.

  19. Propagation Delay of 74XX00 Gates

  20. Propagation Delay in Logic Circuits • Sum of the delays in the input-to-output paths. • Delays that do not affect the circuit output are ignored.

  21. Propagation Delay in Logic Circuits

  22. Input Data to Clock Timing • Setup time (tsu) – the time required for the synchronous inputs of a flip-flop to be stable before the clock active edge. • Hold time (th) – the time that the synchronous inputs of a flip-flop must remain stable after the clock active edge.

  23. Input Data to Clock Timing

  24. Clock Timing Requirement – 1 • Pulse width (tw) is the minimum time required for an active-level pulse applied to a input. • Values are measured from the midpoint of the leading edge of the pulse to the midpoint of the trailing edge.

  25. Clock Timing Requirement – 1

  26. Clock Timing Requirement – 2 • Recovery time (trec) is the time from the midpoint of the trailing edge of a pulse to the midpoint of an active edge CLK edge (See Table 11.4 in the textbook). • For a flip-flop, the propagation delay due to the clock is defined as the delay measured from the active edge of the clock to a corresponding change in Q.

  27. Clock Timing Requirement – 3

  28. Fanout • The number of gates that a logic gate is capable of driving without possible logic error. • Limited by the maximum current a gate can supply in a given logic state versus the current requirements of the load.

  29. Fanout Definitions • Driving gate is the gate whose output supplies current to the inputs of other gates. • Load gate is a gate whose input current is supplied by the output of another gate.

  30. Fanout Definitions

  31. Current Output Definitions • Sourcing means that the current flows out of the terminal. • Sinking means that the current flows into the terminal.

  32. Current Output Definitions

  33. Driving Gate Fanout • May be different for sourcing and sinking.

  34. Fanout Example for 74LS00 • IOL = 8 mAIIL = –0.4 mAnL = 20 • IOH = –0.4 mAIIH = 20 μAnH = 20

  35. Current Designations • Sourcing currents are designated as negative. • Sinking currents are designated as positive. • Sign is disregarded in fanout calculations.

  36. Exceeding Fanout • Output voltage VOL increases with increasing sink current. • Output voltage VOH decreases with increasing source current. • A greater load in either state takes the output voltage further away from its nominal value.

  37. Power Dissipation • The measure of energy used over time by electronic logic gates. • The product of the voltage and current required for the operation of the circuit.

  38. Power Dissipation in TTL Devices • PD = VCCICC. • VCC = power supply voltage. • ICC = current used. • In general, ICC = (ICCH + ICCL)/2.

  39. Power Dissipation in TTL Devices

  40. ICCL and ICCH • ICCL is the current drawn from the supply when all outputs are LOW. • ICCH the current drawn form from the supply when all outputs are HIGH.

  41. Power Dissipation in CMOS Devices • PD = VCCIT. • VCC = power supply voltage. • IT = quiescent + dynamic supply current.

  42. CMOS Quiescent vs. Dynamic Current • Quiescent current flows when the gate is in a steady state and is usually small. • Dynamic current flows when the gate is changing state. • The faster a CMOS gate switches, the more current (and the more power) it requires.

  43. Power Dissipation of TTL vs. CMOS • Power dissipation in TTL is independent of frequency. • Power dissipation in CMOS is dependent on frequency. • In slow circuits (< 1 MHz), CMOS is generally superior.

  44. Noise • Unwanted electrical signals. • Induced by electromagnetic fields by such sources as motors, fluorescent lights, high-frequency circuits, and cosmic rays. • Can cause erroneous operation of a digital circuit.

  45. Noise Margin • A certain amount of tolerance is built into digital devices to tolerate noise. • Noise margin is required for both LOW and HIGH inputs (See Figure 11.15 in the textbook).

  46. Noise Margin for 74LS04 • HIGH state:VNH = VOH – VIH = 3.0 V – 2.0 VVNH = 1.0 V. • LOW state:VNL = VIL – VOL = 0.8 V – 0.5 VVNL = 0.3 V.

  47. Noise Margin for 74HC00A • HIGH state:VNH = VOH – VIH = 3.98 V – 3.15 VVNH = 0.63 V. • LOW state:VNL = VIL – VOL = 1.35 V – 0.26 VVNL = 1.09 V.

  48. Interfacing TTL and CMOS • An extension of fanout and noise margin calculations. • Requires knowledge of input and output voltages and currents for the gates in question. • Refer to Table 11.5 in the textbook.

  49. High-Speed CMOS Driving 74LS • In general, the 74HC family satisfies the input voltage requirements of the 74LS family. • In general, the 74HC family can drive the 74LS family directly, with a fanout of 10.

  50. 74LS Driving 74HC • In general, the 74LS family satisfies the LOW-state criterion, but cannot guarantee sufficient output voltage in the HIGH state. • Requires a pull-up resistor on the output to ensure sufficient HIGH-state voltage at the 74HC input.

More Related