1 / 23

Protection in Virtual Mode

Protection in Virtual Mode. All VM Tasks execute at a privilege level 3 . Virtual 8086 mode are subject to all protection checks defined in protection mode An attempt to execute privileged instruction will cause an exemption. Structure of a V86 Task. A V-86 task consists

alyssaj
Télécharger la présentation

Protection in Virtual Mode

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Protection in Virtual Mode • All VM Tasks execute at a privilege level 3. • Virtual 8086 mode are subject to all protection checks defined in protection mode • An attempt to execute privileged instruction will cause an exemption

  2. Structure of a V86 Task • A V-86 task consists • Partly of 8086 program • Partly of 80386 code that serves as the VM (Virtual Machine)monitor (80386 protected mode code (PL=0) with initialization and exception handling procedures) • To run in V86 mode, 8086 program needs: • A V-86 monitor • Operating System Services

  3. Entering and Leaving V86 Mode • The processor can enter V86 by two means: • Case 1: • A task switch to an 80386 task loads the image of EFLAGS from the new TSS. • The TSS of the new task contains the VM flag • VM = 1 of the new EFLAGS indicates that the new task is executing 8086 instructions and therefore the segment registers from the TSS forms base addresses as 8086 would.

  4. Entering and Leaving V86 Mode • Case 2: • An IRET from a procedure of an 80386 task loads the image of EFLAGS from the stack • VM = 1 indicates that the procedure to which control is being returned is an 8086 procedure • CPL at the time IRET is executed must be zero, else the processor does not change VM.

  5. Entering and Leaving V86 Mode • The processor leaves V86 mode when an interrupt or exception occurs. • Case 1: • The interrupt or exception causes a task switch which loads EFLAGS from the TSS of the new task. • If the new TSS is an 80386 TSS and VM bit is 0 in the EFLAGS, then the processor • clears the VM bit of EFLAGS • loads the segment registers from the new TSS and • begins executing the instructions of the new task according to 80386 protected-mode semantics.

  6. Entering and Leaving V86 Mode • Case 2: • The interrupt or exception vectors to a privilege-level zero procedure. • The processor stores the current setting of EFLAGS on the stack, then clears the VM bit. • The interrupt or exception handler, therefore, executes as 80386 protected-mode code

  7. Chapter 3 P5 Micro architecture : Intel’s Fifth generation

  8. Features of Pentium • Introduced in 1993 with clock frequency ranging from 60 to 66 MHz • The primary changes in Pentium Processor were: • Superscalar Architecture • Dynamic Branch Prediction • Pipelined Floating-Point Unit • Separate 8K Code and Data Caches • Writeback MESI Protocol in the Data Cache • 64-Bit Data Bus • Bus Cycle Pipelining

  9. Pentium Architecture UQ: Explain with block diagram how superscalar operation is carried out in Pentium Processor UQ:Draw and explain Pentium Processor architecture . Highlight architectural features

  10. Pentium Architecture • It has data bus of 64 bit and address bus of 32-bit • There are two separate 8kB caches – one for code and one for data. • Each cache has a separate address translation TLB which translates linear addresses to physical. • Code Cache: • 2 way set associative cache • 256 lines b/w code cache and prefetch buffer, permitting prefetching of 32 bytes (256/8) of instructions

  11. Pentium Architecture • Prefetch Buffers: • Four prefetch buffers within the processor works as two independent pairs. • When instructions are prefetched from cache, they are placed into one set of prefetch buffers. • The other set is used as when a branch operation is predicted. • Prefetch buffer sends a pair of instructions to instruction decoder

  12. Pentium Architecture • Instruction Decode Unit: • It occurs in two stages – Decode1 (D1) and Decode2(D2) • D1 checks whether instructions can be paired • D2calculates the address of memory resident operands

  13. Pentium Architecture • Control Unit : • This unit interprets the instruction word and microcode entry point fed to it by Instruction Decode Unit • It handles exceptions, breakpoints and interrupts. • It controls the integer pipelines and floating point sequences • Microcode ROM : • Stores microcode sequences

  14. Pentium Architecture • Arithmetic/Logic Units (ALUs) : • There are two parallel integer instruction pipelines: u-pipeline and v-pipeline • The u-pipeline has a barrel shifter • The two ALUs perform the arithmetic and logical operations specified by their instructions in their respective pipeline

More Related