1 / 29

Pulp and Paper Making in South Africa

Pulp and Paper Making in South Africa. Raw Materials Derived from Renewable Resources . Pulping Processes. Chemical Pulping Mechanical Pulping Chemo-Mechanical or Semi Chemical Waste Repulping. Mechanical Pulping. Mechanical action breaks the ML which is more brittle than the fibre wall.

aquarius
Télécharger la présentation

Pulp and Paper Making in South Africa

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Pulp and Paper Makingin South Africa

  2. Raw Materials Derived from Renewable Resources

  3. Pulping Processes • Chemical Pulping • Mechanical Pulping • Chemo-Mechanical or Semi Chemical • Waste Repulping

  4. Mechanical Pulping • Mechanical action breaks the ML which is more • brittle than the fibre wall. • The fibre wall is left intact, but substantial fibre cutting occurs • Chemical composition is not altered very much.

  5. Mechanical Pulping • Wood physically taken apart – recovery high • Dense species not usually used due to short thick walled fibres and high % of vessels • Resinous species can also present problems • Yield - high but pulp unsuitable for many uses due to lignin content which stiffens fibres • Lignin also results in yellowing of pulp with time

  6. Mechanical Pulping -SWG Mechanical Pulping – SWG Pulp produced by pressing logs against rotating grindstone 􀂾 Fibres are compressed, and loosened 􀂾 Friction creates heat to soften the lignin

  7. Mechanical Pulping -Refiner Mechanical Pulp (RMP) Wood chips are broken down into fibres by bars on two rotating or one rotating and one stationary discs

  8. Chemi-thermomechanicalPulps (CTMP) To decrease energy cost or to improve pulp quality, chemical treatments (alkaline sulphite, sodium sulphite) are often added to mechanical pulping 􀂾Pretreatment of chips (to lower energy) 􀂾Inter-stage treatment (lower energy, increase fibre flexiblity) 􀂾Post-treatment (fibre flexiblity)

  9. Chemical Pulping Chemicals degrade & dissolve the lignin. 􀂾 Hemicellulose also removed. 􀂾 Mainly secondary wall material remains

  10. Chemical Pulping • Soda • Soda Anthra Quinone • Kraft = Caustic Soda + Sodium Sulphide (High strength; efficient recovery of chemicals; handles a variety of species; tolerates bark) • Neutral Sulphite Semi Chemical = Sodium Carbonate + Sodium Sulphite • Sulphite – H2SO3 + bisulfite; bright pulp & easy to bleach; higher yield; easier to refine

  11. Kraft Recovery Cycle • Black Liquor is Concentrated in Multiple Effect Evaporators to about 65 – 70% Solids • This Heavy Black Liquor is fired in a Soda Recovery Furnace • The Smelt is dissolved in water to form Green Liquor – Sodium Carbonate and Sodium Suphide • Green Liquor is causticised with un-slaked lime, filtered and polished to form white liquor • The Calcium Carbonate sludge is burnt in Kilns

  12. Soda Recovery • Soda or Soda/AQ Liquor is concentrated to 55-60% Solids in Multiple Effect Evaporators • Strong Liquor is sprayed to form droplets in a Fluidized Bed Reactor • Further evaporation takes place as droplets fall • Organics burn in the fluidized bed • Inorganics recovered in the form of Sodium Carbonate

  13. Washing 􀂾 Aim is to: • minimize black liquor carryover • recover dissolved solids 􀂾 Solution contains • Lignin (30-45 %) • Hemicellulose (28-36 %) • Extractives (2-5 %) • Na2O (25-40 %)

  14. Beating andRefining 􀂾 Purpose 􀂾 To flatten fibres to ensure maximum surface area for hydrogen bonding in paper 􀂾 Beating also unravels fibres 􀂾 Beating is done in refiners 􀂾 Fluted plug rotates inside similar shaped housing with ribs

  15. Beating andRefining Freeness 􀂾 Freeness is term used to describe pulp potential 􀂾 Measured by rate of water passing through set amount of fibre formed on wire mesh 􀂾 Well beaten fibre does not allow water to pass, so Freeness is low 􀂾 Burst and tensile strength increased by beating time – increases inter-fibre bonding

  16. Chemical vs. Mechanical Pulping

  17. Chemical vs. Mechanical Pulping

  18. Bleaching ProcessesConventional • Chlorination – Elemental Chlorine (aromatic substitution of H and addition reactions over the C=C) • Alkali Extraction – Sodium Hydroxide • Chlorine Dioxide or Sodium Hypochlorite • Alkali Extraction

  19. Bleaching ProcessesModern Trends • Sulpher Dioxide • Oxygen (radical mechanism) or Ozone (addition over the C=C) • Chlorine Dioxide • Alkali Extraction • Chlorine Dioxide • Hydrogen Peroxide • Exotics

  20. Paper Making Chemicals • Cellulose Fibers – the bulk • Fillers – Clay, Calcium Carbonate – 0 to 25% • Strength Additives – Starch, CMC – 0 to 10% • Sizing Agents – Rosin + Alum, AKD, ASA • Wet Strength Additives – 0 to 2% • Dyes • Retention Agents

  21. Major Grades of Paper

  22. South African Pulp and paper Industry • Number of Paper & Board Mills – 17 • Number of Pulp Mills – 9 • Paper & Board Capacity = 2.421 Mt – Local Consumption = 75% • Pulp Capacity = 2.472 Mt – Local consumption = 60% • The Industry is a very important foreign exchange earner

  23. Per Capita Paper Consumption kg

  24. Pulp and Paper Makingin South Africa

More Related