1 / 43

UAV Research International

UAV Research International. “Providing integrated consultation to MAV project engineers at Eglin AFB” Chris McGrath Neil Graham Alex von Oetinger John Dascomb Sponsor : Dr. Gregg Abate April 6, 2006. Overview. Problem Statement Design Specifications Design Solution

havily
Télécharger la présentation

UAV Research International

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. UAV Research International “Providing integrated consultation to MAV project engineers at Eglin AFB” Chris McGrath Neil Graham Alex von Oetinger John Dascomb Sponsor : Dr. Gregg Abate April 6, 2006

  2. Overview • Problem Statement • Design Specifications • Design Solution • Scale Model Design/Fabrication • Testing

  3. Problem Statement • To design a means of characterizing MAV handling during flight • Test must be repeatable • Data must be collected to characterize the MAV

  4. Project Specifications • Weight  100 – 200 grams (g) • Flight Speed  0 – 25 meters per second (m/s) • Exterior Material  Carbon Fiber Composite • Wing Tip Length  15 – 30 centimeters (cm) • MAV Flight Control  Both 2 and 3 axis • Type of Thrust  Pusher, Puller, None

  5. Design Selection:Free Flight Wind Tunnel • The free flight wind tunnel has been successfully created before • Design is a conventional wind tunnel with unobstructed test section • Relative velocity of MAV to the ground is zero

  6. MAV Handling: Initial Set-up

  7. MAV Handling:Reel and Restraint Set-up

  8. Wind Tunnel Design • In wind tunnel design Three properties are most important to consider: • Tunnel geometry • Flow quality • Fan Selection

  9. Wind Tunnel Design

  10. Wind Tunnel Geometry:Test section Dimensions • For the minimum analysis of the flight, the MAV needs to move laterally or vertically twice its wingspan • Minimum cross section for 12” wingspan is 4.5 ft x 4.5 ft • Allow ten feet for longitudinal motion

  11. Wind Tunnel Geometry

  12. Wind Tunnel Geometry:1st Diffuser • Expands the ducting from area of test section to the area of the fan • Diffuser angle < 5° for laminar flow

  13. Wind Tunnel Geometry

  14. Wind Tunnel Design:Turns 1 and 2 • Corner Vanes assist flow around the 4 90 degree turns • Corner Vanes improve efficiency by decreasing pressure loss • Even with vanes 61% of all pressure loss occurs at the 1st two turns

  15. Wind Tunnel Geometry

  16. Wind Tunnel Design:Fan Selection • Fan selection based on volume flow rate and static pressure loss in tunnel • Volume flow rate at maximum of 25 m/s is 100000 CFM • Total pressure loss in tunnel = 600 Pa

  17. Wind Tunnel Design:Fan Selection • Howden Buffalo 54-26 series fan • Fan has a 54 in diameter, and a 125 HP motor

  18. Wind Tunnel Design:Flow Quality • Motor housing • Anti-swirl vanes

  19. Wind Tunnel Geometry

  20. Wind Tunnel Geometry:2nd Diffuser, Turns 3 and 4 • Diffuser increases area final area ratio of 6 • Final area ratio is most important factor in tunnel • Turning vanes keep flow as laminar as possible

  21. Wind Tunnel Geometry

  22. Wind Tunnel Design:Flow Quality • Honeycombs - remove lateral components of turbulence • 3 Screens – remove axial components of turbulence

  23. Wind Tunnel Geometry:Contraction Cone • Contraction cone quickly increases flow velocity • When condensing, flow will not separate like diffuser

  24. Wind Tunnel Geometry :Tunnel Geometry – Constrained tunnel Total tunnel length is 36.6 ft

  25. Instrumentation • On-Board Measurement • Flow Quality Measurement • Traversing System • Data Collection Software • Data Acquisition System

  26. On-Board Measurement • Kestrel Autopilot • 16.65 grams (2” x 1.37” x .47”) • Three-axis rate gyros • Accelerometers • Air pressure sensors

  27. Data Collection Software • Virtual Cockpit • Labview

  28. Cost Analysis

  29. Scale Model • Too expensive to build the designed tunnel • Built a 1/12 scale model • Physically test flow quality of full scale design to determine if free flight is feasible

  30. Scale Effects • Scale model Reynolds number 1/12 that of full scale model • Use hot-wire Anemometer to measure velocity fluctuation though test section • Velocity is not dependent on Reynolds number, scaling effects can be ignored for our tests

  31. Scale Model

  32. Contraction Cone

  33. Contraction Cone Total Elapsed Time: 2 Hours 20 Hours

  34. Contraction Cone Total Elapsed Time: 41 Hours

  35. Contraction Cone

  36. Joining Method

  37. Turning Vanes

  38. Diffusers

  39. Settling Chamber

  40. Fan

  41. Model Results • Manufacturing Complete • Testing • Initial correction of flow through turning vanes • Inconclusive analysis of tunnel due to lack of testing • Potential Testing • Fine tune internal geometry • Correction of all Turning vanes • Measuring Pressure fluctuations through test section

  42. Problems Encountered • Wait time on ordered parts • MSC acrylic sheets • McMaster-Carr fan order • Fabrication of contraction cone • Testing Time Constraints

  43. Questions?

More Related